QUINT-PS-3x400-500AC/24DC/10
3-Phase Primary-Switched Power Supply Unit
INTERFACE
Data Sheet
Description
QUINT POWER devices are 60...960 W DC power supply
units for universal use. This is ensured by the wide-range
input, single and three-phase versions, and an international
approval package.
QUINT POWER stands for guaranteed supply: powerful
capacitors ensure mains buffering of more than 20 ms at full
load.
All three-phase devices provide the full output power, even
in the event of a continuous phase failure.
The POWER BOOST power reserve starts loads with high
inrush currents and ensures that fuses are reliably tripped.
Preventive function monitoring diagnoses impermissible
operating states and minimizes downtimes in your system.
An active transistor output and a floating relay contact are
used for remote monitoring.
All QUINT POWER devices are idling-proof and short-
circuit proof, and are available with a regulated and
adjustable output voltage of 12, 24, and 48 V DC with output
currents of 2.5, 5, 10, 20, 30, and 40 A.
Power supply units for use in Ex Zone 2, uninterruptible
solutions, AS-i power supply units, and a QUINT diode
complete the product range.
QUINT POWER is a built-in device. Installation
and startup must only be carried out by
qualified personnel. The relevant country-
specific regulations (e.g., VDE, DIN) must also
be observed.
© PHOENIX CONTACT - 12/2005
Danger
The device contains dangerous live elements and high levels of stored energy.
Never carry out work when the power is turned on.
Risk of burns
The housing temperature can reach high values depending on the ambient temperature and the load of the
device.
Make sure you always use the latest documentation.
It can be downloaded at
www.download.phoenixcontact.com.
A conversion table is available on the Internet at
www.download.phoenixcontact.com/general/7000_en_00.pdf.
This data sheet is valid for all products listed on the following page:
100033_04_en
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany
Phone: +49 - 52 35 - 30 0 • Fax: +49 - 52 35 - 34 12 00 • www.phoenixcontact.com
www.phoenixcontact.com/salesnetwork
1
QUINT-PS-3x400-500AC/24DC/10
Ordering Data
Product
Description
3-phase primary-switched power supply unit
Type
QUINT-PS-3x400-500AC/24DC/10
Order No.
29 38 61 7
Pcs./Pkt.
1
Accessories
Description
Assembly adapter for QUINT POWER 10 A on S7 300 rails
Type
QUINT-PS-ADAPTERS7/2
Order No.
29 38 20 6
Pcs./Pkt.
1
Technical Data
Input Data
Nominal input voltage range
Input voltage range
Frequency range
Current consumption
Inrush current surge
Mains buffering (for nominal load)
Typical switch-on time
Protective circuit
Input fuse
Recommended backup fuse
Discharge current to PE
Connection method
Stripping length
3 x 400...500 V AC
320...575 V AC (for all three phases), 450...800 V DC
45...65 Hz (0 Hz at DC input)
0.63 A (for all three phases at 400 V AC (nominal load)), approximately
0.57 A (for all three phases at 480 V AC (nominal load)), approximately
< 15 A (typical), inrush current limiting/Ι
2
t (25°C): < 4 A²s
> 40 ms (at 3 x 400 V AC), > 40 ms (at 3 x 480 V AC)
<1s
Transient surge protection varistor
External via 3 circuit breakers 6 A, 10 A or 16 A, Characteristic B
3 x circuit breaker 6 A, 10 A or 16 A, Characteristic B
< 3.5 mA
Screw connection
7 mm
Output Data
Nominal output voltage
Setting range for the output voltage
Output current
Derating
Current limit
System deviation
24 V DC ±1%
22.5...28.5 V DC
10 A (-25...+60°C)
15 A (with POWER BOOST, -25...+40°C)
Above +60°C: 2.5% per Kelvin
I
BOOST
= 15 A (for short circuit), approximately
< 1% (static load change 10...90%)
< 2% (dynamic load change 10...90%)
< 0.1% (input voltage change ±10%)
28 W
4W
> 90% for 230 V AC and nominal values
< 2 ms (U
OUT
(10...90%))
< 100 mV
pp
(for nominal values)
Yes, to create redundant systems and increase efficiency
COMBICON screw/plug-in connection
7 mm
Power dissipation
Maximum nominal load
Maximum no load
Efficiency
Rise time
Residual ripple/switching peaks (20 MHz)
Parallel connection
Connection method
Stripping length
DC OK Signal Output, Active
Type of output
Continuous current
Output voltage
Transistor output, U
out
> 0.9 x U
N
: High signal
40 mA, maximum
+24 V DC (signal)
DC OK Signal Output, Floating
Type of output
Continuous current
Maximum switching voltage
Relay contact, U
out
> 0.9 x U
N
: Contact closed
1 A, maximum
30 V AC/DC, maximum
100033_04_en
PHOENIX CONTACT
2
QUINT-PS-3x400-500AC/24DC/10
General Data
Insulation voltage
Input/output
Input/PE
Insulation voltage output/PE
Mounting position
Degree of protection
Protection class
MTBF
Housing version
Weight
Dimensions (width x height x depth)
Dimensions (width x height x depth) for alternative assembly
4 kV AC (type test)/2 kV AC (routine test)
3.5 kV AC (type test)/2 kV AC (routine test)
500 V DC (routine test)
On horizontal NS 35 DIN rail according to EN 60715
IP20
Ι,
with PE connection
> 500,000 h according to IEC 61709 (SN 29500)
AluNox (AlMg1), closed
1.400 kg
85 mm x 130 mm x 125 mm
122 mm x 130 mm x 88 mm
Status Indicators
DC OK status indicator
Green LED (U
out
< 0.9 x U
N
: LED flashes)
Climatic Data
Ambient temperature (operation)
Ambient temperature (storage/transport)
Maximum permissible humidity (operation)
Vibration (operation)
Shock
Pollution degree
Climatic class
-25...+70°C (> 60°C derating)
-40...+85°C
95% (at +25°C, no condensation)
< 15 Hz, amplitude ±2.5 mm according to IEC 60068-2-6
15...150 Hz, 2.3g, 90 minutes
30g in all space directions, according to IEC 60068-2-27
2 according to EN 50178
3K3 according to EN 60721
Certification/Standards
Electrical equipment of machines
Safety transformers for switched-mode power supply units
Electrical safety (of IT equipment)
EN 60204 (Surge Voltage Category III)
EN 61558-2-17
EN 60950/VDE 0805 (SELV), EN 61558-2-17
CB Scheme
j
Industrial control equipment
Electrical equipment for potentially explosive areas
Shipbuilding
Electronic equipment for use in electrical power installations
Safety extra-low voltage
Safe isolation
Protection against electric shock
Protection against electric shock, basic requirements for safe isolation in
electrical equipment
Limitation of harmonic line currents
Device safety
UL/C-UL Recognized UL 60950
u
UL/C-UL Listed UL 508
U
LISTED
UL/C-UL Recognized UL 1604, Class
Ι,
Division 2, Groups A, B, C, D
Germanischer Lloyd
F
, ABS
EN 50178 (VDE 0160)
PELV (EN 60204), SELV (EN 60950)
DIN VDE 0100-410
DIN 57100-410
DIN VDE 0106-101
According to EN 61000-3-2
B
(tested safety)
100033_04_en
PHOENIX CONTACT
3
QUINT-PS-3x400-500AC/24DC/10
Conformance With EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC
Noise Immunity Test According to EN 61000-6-2
1
Electrostatic discharge (ESD)
EN 61000-4-2
Criterion B
2
Housing
Level 4
Air discharge 15 kV
Contact discharge 8 kV
Electromagnetic HF field
EN 61000-4-3
Criterion A
3
Housing Level 3
Frequency range 80...1000 MHz/1.4...2.0 GHz
Field strength 10 V/m
Fast transients (burst)
EN 61000-4-4
Criterion B
2
Input 4 kV (Inst. Class 4, asymmetrical: Cable to ground)
2 kV (Inst. Class 4, symmetrical: Cable to cable)
Output 0.5 kV (Level 1, asymmetrical: Cable to ground)
0.5 kV (Level 1, symmetrical: Cable to cable)
Signal 1 kV (Level 1, asymmetrical: Cable to ground)
Surge current load (surge)
EN 61000-4-5
Criterion B
2
Input 4 kV (Level 4, asymmetrical)
Output 2 kV (Level 3, asymmetrical)
Signal 1 kV (Level 2, asymmetrical)
Conducted interference
EN 61000-4-6
Criterion
A
3
Input/output/signal Level 3, asymmetrical
Frequency range 0.15...80 MHz
Voltage 10 V
Voltage dips
Noise emission of housing
1
2
3
4
EN 61000-4-11 Criterion B
EN 55011
(EN 55022)
4
Class B
Input Mains buffering > 20 ms
Industrial and domestic applications
Noise Emission Test According to EN 61000-6-3
EN 61000 corresponds to IEC 61000
Criterion B:
Criterion A:
Temporary adverse effects on the operating behavior, which the device corrects automatically.
Normal operating behavior within the specified limits.
EN 55011 corresponds to CISPR11/EN 55022 corresponds to CISPR22
Structure
7
1
2
13
13
14
DC
OK
Ou
K
tp
ut
14
D
C
O
DC
24
V
4
13
13
10
A
3
DC
2
L1
L2
OK
22 Ad
,5- ju
28 st
,5V
14
D
OK C
Inp
AC ut
4
L3
00 -
L3
50
0V
3
4
5
6
7
AC input
85...264 V AC input voltage,
45...65 Hz frequency
DC output
24 V DC output voltage (default),
can be set between 22.5 and 28.5 V DC
DC OK output active
DC OK output floating
Potentiometer (covered) 22.5...28.5 V DC
DC OK LED
Universal DIN rail adapter UTA 107
14
D
C
Ou
OK
QUINT POWER
tp
ut
DC
Block Diagram
6
5
L1 (+)
L2
L3 (-)
24
V
10
A
1
DC
OK
Figure 1
Operating elements
PE
DC OK
13
14
Figure 2
Block diagram
100033_04_en
PHOENIX CONTACT
4
QUINT-PS-3x400-500AC/24DC/10
Safety Notes and Warning Instructions
Danger
The device contains dangerous live elements
and high levels of stored energy.
Never carry out work when the power is turned
on.
Risk of burns
The housing temperature can reach high
values depending on the ambient temperature
and the load of the device.
To ensure that the device can be operated safely and all
functions can be used, please read these instructions
carefully.
QUINT POWER is a built-in device. Installation
and startup must only be carried out by
qualified personnel. The relevant country-
specific regulations (e.g., VDE, DIN) must also
be observed.
–
–
–
Before startup please ensure:
–
The mains has been connected correctly
and protection is provided against electric
shock.
The device can be switched off outside the
power supply according to EN 60950
regulations (e.g., by the line protection on
the primary side).
The protective conductor is connected.
All supply lines have sufficient fuse
protection and are the correct size.
All output cables are the correct size for
the maximum device output current or
have separate fuse protection.
Sufficient convection is ensured.
–
–
Installation
Risk of burns
The housing temperature can reach high
values depending on the ambient temperature
and the load of the device.
QUINT POWER
13
14
13
D
OK C
Ou
14
D
OC
K
tp
ut
DC
24
V
10
A
To ensure sufficient convection, the following
minimum spacing is required between other
modules:
5 cm above and below the device.
No minimum spacing to other modules at the
sides is required for proper operation of the
device.
The power supply unit can be snapped onto all DIN rails
according to EN 60715 and must be mounted horizontally
(connection terminal blocks facing downwards).
DC
OK
22 Ad
,5- ju
28 st
,5V
L1
L2
Inp
AC ut
4
L3
00 -
L3
50
0V
Figure 3
Convection
100033_04_en
PHOENIX CONTACT
5
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
