For more information, please visit the
product page.
CUI Inc
│
SERIES:
VIBLSD1-SIP
│
DESCRIPTION:
DC-DC CONVERTER
date
02/09/2015
│
page
2 of 5
PART NUMBER KEY
VIBLSD1 - SXX - SXX -SIP
Base Number
Input Voltage
Output Voltage
Packaging Style
INPUT
parameter
operating input voltage
conditions/description
5 Vdc models
12 Vdc models
15 Vdc models
24 Vdc models
min
4.75
11.4
14.25
22.8
typ
5
12
15
24
max
5.25
12.6
15.75
25.2
units
Vdc
Vdc
Vdc
Vdc
OUTPUT
parameter
line regulation
load regulation
voltage accuracy
switching frequency
temperature coefficient
100% load, input voltage range
120
±0.03
conditions/description
for Vin change of 5%
measured from 10% load to full load
min
typ
max
±0.25
±2
±3
300
units
%
%
%
kHz
%/°C
PROTECTIONS
parameter
short circuit protection
conditions/description
5 and 24 Vdc output models
all other models: continuous
min
typ
max
1
units
s
SAFETY AND COMPLIANCE
parameter
isolation voltage
isolation resistance
MTBF
RoHS
conditions/description
for 1 minute at 1 mA max.
at 500 Vdc
as per MIL-HDBK-217F @ 25°C
2011/65/EU
min
1,000
1,000
3,500,000
typ
max
units
Vdc
MΩ
hours
ENVIRONMENTAL
parameter
operating temperature
storage temperature
storage humidity
temperature rise
hand soldering
non-condensing
at full load
1.5 mm from case for 10 seconds
15
conditions/description
see derating curve
min
-40
-55
typ
max
85
125
95
25
300
units
°C
°C
%
°C
°C
cui.com
For more information, please visit the
product page.
CUI Inc
│
SERIES:
VIBLSD1-SIP
│
DESCRIPTION:
DC-DC CONVERTER
date
02/09/2015
│
page
4 of 5
APPLICATION NOTES
1.
Requirement on Output Load
In order to ensure the product operates efficiently and reliably, make sure the specified range of input voltage is not exceeded and the
minimum output load is not less than 10% load. If the actual load is less than the specified minimum load, the output ripple may
increase sharply while its efficiency and reliability will reduce greatly. If the actual output power is very small, please add an
appropriate resistor as extra loading.
Overload Protection
Under normal operating conditions, the output circuit of these products has no protection against over-current and short-circuits. The
simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit.
Filtering
In some circuits which are sensitive to noise and ripple, a filtering capacitor may be added to the DC/DC output end and input end to
reduce the noise and ripple. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a
startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest
capacitance of its filter capacitor sees the external capacitor table. To get an extremely low ripple, an “LC” filtering network may be
connected to the input and output ends of the DC/DC converter, which may produce a more significant filtering effect. It should also
be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid
mutual interference (Figure 1).
L
L
2.
3.
Figure 1
Vin
+Vo
C
GND
DC DC
C
0V
4.
Output Voltage Regulation and Over-voltage Protection Circuit
The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat
protection that is connected to the input or output end in series (Figure 2).
Figure 2
Vin
GND
REG
+Vout
DC DC
0V
5.
External Capacitor Table
It is not recommended to connect any external capacitor in the application field with less than 0.5 W output.
Vin
(Vdc)
Cin
(µF)
4.7
4.7
2.2
1
--
Vout
(Vdc)
5
9
12
15
24
Cout
(µF)
10
4.7
2.2
1
0.47
Table 1
5
12
15
24
--
Notes:
1. Operation under minimum load will not damage the converter; however, they may not meet all specifications listed.
2. Max. capacitive load tested at input voltage range and full load.
3. All specifications measured at: Ta=25°C, humidity<75%, nominal input voltage and rated output load, unless otherwise specified.
cui.com
For more information, please visit the
product page.
CUI Inc
│
SERIES:
VIBLSD1-SIP
│
DESCRIPTION:
DC-DC CONVERTER
date
02/09/2015
│
page
5 of 5
REVISION HISTORY
rev.
1.0
1.01
1.02
1.03
1.04
description
initial release
new template applied, V-Infinity branding removed,
0.75 watt, 15 V
dc
input & 24 V
dc
output models added
removed UL marking from datasheet
updated spec
updated spec
date
12/09/2005
09/06/2012
01/10/2013
07/11/2013
02/09/2015
The revision history provided is for informational purposes only and is believed to be accurate.
Headquarters
20050 SW 112th Ave.
Tualatin, OR 97062
800.275.4899
CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website.
Fax 503.612.2383
cui.com
techsupport@cui.com
CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is
assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use.
CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical
component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to
affect its safety or effectiveness.
DSP 与 ARM 处理器
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
