USER’S MANUAL
ISL281x8EVAL1Z
Evaluation Board
AN1350
Rev 0.00
Aug 14, 2007
and V- terminals connect to their respective power supply
terminals. De-coupling capacitors C
1
andC
2
connect to
ground through R
1
and R
21
0 resistors. Resistors R
20
and
R
24
are 0 but can be changed by the user to provide
additional power supply filtering, or to reduce the voltage
rate-of-rise to less than ±1V/µs. Two additional capacitors,
C
3
and C
4
are connected close to the part to filter out high
frequency noise. Anti-reverse diodes D
1
and D
2
protect the
circuit in the case of accidental polarity reversal.
J3
V-
J2
J1
R1
0
C1
+
D1 4.7µF
R24
0
C3
0.1µF
VM
VP
VOUT
RL
10k
V+
Introduction
The ISL281x8EVAL1Z evaluation board is a design platform
containing all the circuitry needed to characterize critical
performance parameters of the ISL281x8 operational
amplifiers, using a variety of user defined test circuits.
The ISL28138 and ISL28148 high-speed operational
amplifiers feature low power consumption, while the
ISL28158 and ISL28168 operational amplifiers feature
ultra-low power consumption. All op amps have rail-to-rail
output drive capability and are designed to operate with a
single lithium cell or two Ni_Cd batteries.
Reference Documents
R20
R21
C2
+
4.7µF D2 0
• ISL28138 Data Sheet, FN6336
• ISL28148 Data Sheet, FN6337
• ISL28158 Data Sheet, FN6377
• ISL28168 Data Sheet, FN6378
C4
0.1µF
Evaluation Board Key Features
The ISL281x8EVAL1Z is designed to enable the IC to
operate from a single supply, +2.4VDC to +5.5VDC or from
split supplies, ±1.2VDC to ±2.75V. The board is configured
for a single op amp connected for differential input with a
closed loop gain of 10. It also contains a single external
reference voltage (VREF) pin and provisions for a
user-selectable voltage divider (filter are included).
FIGURE 1. POWER SUPPLY CIRCUIT
Amplifier Configuration (
Figure
2)
The schematic of the op amp with the components supplied
is shown in Figure 2. The circuit implements a differential
input amp with a closed loop gain of 10. The circuit can
operate from a single supply or from dual supplies. The
VREF pin can be connected to ground to establish a ground
referenced input for split supply operation, or can be
externally set to any reference level for single supply
operation.
Power Supplies (
Figure 1
)
External power connections are made through the V+, V-
and Ground connections on the evaluation board. For single
supply operation, the V- and Ground pins are tied together to
the power supply negative terminal. For split supplies V+
RF
100k
RIN-
IN-
10k
IN+
IN+
VCM
VREF
0
RIN+
10k
RREF+
100k
IN+
IN-
0
ISL281x8
IN -
VP
0
-
V+
+
V-
VM
VREF
GND
10k
FIGURE 2.
BASIC AMPLIFIER CONFIGURATION
AN1350 Rev 0.00
Aug 14, 2007
Page 1 of 5
ISL281x8EVAL1Z
User-selectable Options (
Figures 3 and 4
)
Component pads are included to enable a variety of
user-selectable circuits to be added to the amplifier inputs,
the VREF input, outputs and the amplifier feedback loops.
A voltage divider and filter option (Figure 3) can be added to
establish a power supply-tracking common mode reference
at the VREF input. The inverting and non-inverting inputs
have additional resistor placements for adding input
attenuation, or to establish input DC offsets through the
VREF pin.
REF1
RINA-
R10
IN- J6
DNP
R2
R5
DNP
10k
RINA2-
R8
0
C6
R12
DNP
OPEN
RREFA-
R15
DNP
J4
The output (Figure 4) has a 10k load resistor to ground,
and has additional resistor and capacitor placements for
loading.
NOTE: Operational amplfiers are sensitive to output
capacitance and may oscilate. In the event of oscilation,
reduce output capacitance by using shorter cables, or add a
resistor in series with the output.
R17
R18
RREF
C5
+
4.7µF
R22
0
OPEN
R23
DNP
C8
R25
10k
R26
0
DNP
R27
10k
0
TO OUT
J5 OUT
IN1+ J7
C7
IN2+ J8
R3
RINA1+
R7
10k
R6
DNP
R9
RINA+
R11
0
RREFA+
R14
100k
C10
DNP
R13
OPEN
RGA+
TO IN-
TO IN+
OPEN
DNP
DNP
RINA2+
FIGURE 3. 1/2 INPUT STAGE
FIGURE 4. 1/2 OUTPUT STAGE
ISL281x8EVAL1Z Components Parts List
DEVICE NUMBER
C1, C2, C5
C3, C4
C6 to C10
D1, D2
U1 (ISL28138EVAL1Z)
U1 (ISL28148EVAL1Z)
U1 (ISL28158EVAL1Z)
U1 (ISL28168EVAL1Z)
DESCRIPTION
CAP-TANTALUM,S MD, D, 4.7µF, 50V, 10%, LOW ESR, ROHS
CAP, SMD, 0603, 0.1µF, 25V, 10%, X7R, ROHS
CAP, SMD, 0603, DNP-PLACE HOLDER, ROHS
DIODE-RECTIFIER, SMD, SOD-123, 2P, 40V, 0.5A, ROHS
ISL28138FHZ-T7, IC-RAIL-TO-RAIL OP AMP, SOT-23, ROHS
ISL28148FHZ-T7, IC-RAIL-TO-RAIL OP AMP, SOT-23, ROHS
ISL28158FHZ-T7, IC-RAIL-TO-RAIL OP AMP, SOT-23, ROHS
ISL28168FHZ-T7, IC-RAIL-TO-RAIL OP AMP, SOT-23, ROHS
User-selectable resistors - not
populated
0 user selectable resistors
Gain and other user selectable
resistors
Gain resistors
COMMENTS
Power Supply Decoupling
Power Supply Decoupling
User-selectable capacitors - not
populated
Reverse Power Protection
R2, R3, R6, R8, R9, R12, R13, RESISTOR, SMD, 0603, 0.1%, MF, DNP-PLACE HOLDER
R15, R16, R23, R25, R27
R1, R10, R11, R17, R20, R21, RES, SMD, 0603, 0, 1/10W, TF, ROHS
R24, R26, R22
R4, R5, R7, R18
R14, R19
RES, SMD, 0603, 10k, 1/10W, 1%, TF, ROHS
RES, SMD, 0603, 100k, 1/10W, 1%, TF, ROHS
AN1350 Rev 0.00
Aug 14, 2007
OPEN
C9
Page 2 of 5
Notice
1.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation or any other use of the circuits, software, and information in the design of your product or system. Renesas Electronics disclaims any and all liability for any losses and damages incurred by
you or third parties arising from the use of these circuits, software, or information.
2.
Renesas Electronics hereby expressly disclaims any warranties against and liability for infringement or any other claims involving patents, copyrights, or other intellectual property rights of third parties, by or
arising from the use of Renesas Electronics products or technical information described in this document, including but not limited to, the product data, drawings, charts, programs, algorithms, and application
examples.
3.
4.
No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others.
You shall not alter, modify, copy, or reverse engineer any Renesas Electronics product, whether in whole or in part. Renesas Electronics disclaims any and all liability for any losses or damages incurred by
you or third parties arising from such alteration, modification, copying or reverse engineering.
5.
Renesas Electronics products are classified according to the following two quality grades: “Standard” and “High Quality”. The intended applications for each Renesas Electronics product depends on the
product’s quality grade, as indicated below.
"Standard":
Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic
equipment; industrial robots; etc.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control (traffic lights); large-scale communication equipment; key financial terminal systems; safety control equipment; etc.
Unless expressly designated as a high reliability product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas Electronics document, Renesas Electronics products are
not intended or authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems; surgical implantations; etc.), or may cause
serious property damage (space system; undersea repeaters; nuclear power control systems; aircraft control systems; key plant systems; military equipment; etc.). Renesas Electronics disclaims any and all
liability for any damages or losses incurred by you or any third parties arising from the use of any Renesas Electronics product that is inconsistent with any Renesas Electronics data sheet, user’s manual or
other Renesas Electronics document.
6.
When using Renesas Electronics products, refer to the latest product information (data sheets, user’s manuals, application notes, “General Notes for Handling and Using Semiconductor Devices” in the
reliability handbook, etc.), and ensure that usage conditions are within the ranges specified by Renesas Electronics with respect to maximum ratings, operating power supply voltage range, heat dissipation
characteristics, installation, etc. Renesas Electronics disclaims any and all liability for any malfunctions, failure or accident arising out of the use of Renesas Electronics products outside of such specified
ranges.
7.
Although Renesas Electronics endeavors to improve the quality and reliability of Renesas Electronics products, semiconductor products have specific characteristics, such as the occurrence of failure at a
certain rate and malfunctions under certain use conditions. Unless designated as a high reliability product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas
Electronics document, Renesas Electronics products are not subject to radiation resistance design. You are responsible for implementing safety measures to guard against the possibility of bodily injury, injury
or damage caused by fire, and/or danger to the public in the event of a failure or malfunction of Renesas Electronics products, such as safety design for hardware and software, including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult
and impractical, you are responsible for evaluating the safety of the final products or systems manufactured by you.
8.
Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. You are responsible for carefully and
sufficiently investigating applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive, and using Renesas Electronics
products in compliance with all these applicable laws and regulations. Renesas Electronics disclaims any and all liability for damages or losses occurring as a result of your noncompliance with applicable
laws and regulations.
9.
Renesas Electronics products and technologies shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws
or regulations. You shall comply with any applicable export control laws and regulations promulgated and administered by the governments of any countries asserting jurisdiction over the parties or
transactions.
10. It is the responsibility of the buyer or distributor of Renesas Electronics products, or any other party who distributes, disposes of, or otherwise sells or transfers the product to a third party, to notify such third
party in advance of the contents and conditions set forth in this document.
11. This document shall not be reprinted, reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products.
(Note 1)
(Note 2)
“Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its directly or indirectly controlled subsidiaries.
“Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
(Rev.4.0-1 November 2017)
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
1001 Murphy Ranch Road, Milpitas, CA 95035, U.S.A.
Tel: +1-408-432-8888, Fax: +1-408-434-5351
Renesas Electronics Canada Limited
9251 Yonge Street, Suite 8309 Richmond Hill, Ontario Canada L4C 9T3
Tel: +1-905-237-2004
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-651-700, Fax: +44-1628-651-804
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-6503-0, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
Room 1709 Quantum Plaza, No.27 ZhichunLu, Haidian District, Beijing, 100191 P. R. China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 301, Tower A, Central Towers, 555 Langao Road, Putuo District, Shanghai, 200333 P. R. China
Tel: +86-21-2226-0888, Fax: +86-21-2226-0999
Renesas Electronics Hong Kong Limited
Unit 1601-1611, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2265-6688, Fax: +852 2886-9022
Renesas Electronics Taiwan Co., Ltd.
13F, No. 363, Fu Shing North Road, Taipei 10543, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre, Singapore 339949
Tel: +65-6213-0200, Fax: +65-6213-0300
Renesas Electronics Malaysia Sdn.Bhd.
Unit 1207, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics India Pvt. Ltd.
No.777C, 100 Feet Road, HAL 2nd Stage, Indiranagar, Bangalore 560 038, India
Tel: +91-80-67208700, Fax: +91-80-67208777
Renesas Electronics Korea Co., Ltd.
17F, KAMCO Yangjae Tower, 262, Gangnam-daero, Gangnam-gu, Seoul, 06265 Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5338
http://www.renesas.com
© 2018 Renesas Electronics Corporation. All rights reserved.
Colophon 7.0
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
