19-3393; Rev 0; 8/04
MAX8556 Evaluation Kit
General Description
The MAX8556 evaluation kit (EV kit) is a fully assembled
and tested surface-mount circuit board demonstrating
the MAX8556 low-dropout (LDO) regulator. The EV kit
comes assembled with a MAX8556ETE circuit that
steps down a 1.425V to 3.6V input voltage range to a
1.2V output capable of sourcing up to 4A (limited by
power dissipation). The MAX8556 features a POK out-
put that goes high impedance once the output is within
±10% of its regulation value. The device utilizes an
internal p-channel MOSFET for reduced dropout and
quiescent current. In addition, the p-channel MOSFET
eliminates the need for an external bias or noisy charge
pump. The MAX8556 EV kit can also be used to evalu-
ate the MAX8557 with no component changes.
♦
1.425V to 3.6V Input Voltage Range
♦
1.2V Output Voltage
♦
Up to 4A Output Current
♦
Low Dropout Voltage (200mV max at 4A)
♦
Internal p-Channel MOSFET Pass Transistor
♦
Power-OK (POK) Output
♦
Fully Assembled and Tested
Features
Evaluates: MAX8556/MAX8557
Component List
DESIGNATION
C1–C4
QTY
4
DESCRIPTION
10µF
±20%,
6.3V X5R ceramic
capacitors (0805)
Taiyo Yuden JMK212BJ106MG
3-pin header
Sullins PTC36SAAN
100kΩ
±5%
resistor (0603)
1.40kΩ
±0.1%
resistor (0603)
Vishay TNPW06031401BT9RT1
1kΩ
±0.1%
resistor (0603)
Panasonic ERA3YEB102V
MAX8556ETE (16-pin Thin QFN)
Shunt
MAX8556EVKIT PC board
PART
MAX8556EVKIT
Ordering Information
TEMP RANGE
0°C to +70°C
IC PACKAGE
16 Thin QFN 5mm x 5mm
Note:
To evaluate the MAX8557, request a MAX8557ETE free
sample with the MAX8556 EV kit.
JU1
R1
R2
R3
U1
None
None
1
1
1
1
1
1
1
Component Suppliers
SUPPLIER
Panasonic
Taiyo Yuden
Vishay
COMPONENT
Resistors
Capacitors
Resistors
PHONE
714-373-7366
408-573-4150
402-563-6866
WEBSITE
www.maco.panasonic.co.jp
www.t-yuden.com
www.vishay.com
Note:
Indicate that you are using the MAX8556/MAX8557 when contacting these component suppliers.
________________________________________________________________
Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
MAX8556 Evaluation Kit
Evaluates: MAX8556/MAX8557
Recommended Equipment
• One 4V, 5A variable-output power supply
• Dummy load capable of sinking 4A
• Digital multimeter (DMM)
Detailed Description
Adjusting the Output Voltage
R2 and R3 are used to adjust the output voltage for the
MAX8556. To adjust the output voltage, replace R2 with
a 0.1% resistor that is calculated as:
R2 = 1 x 10
3
x ((V
OUT
/ V
FB
) - 1)
where V
FB
is 0.5V and V
OUT
is the desired output voltage.
Quick Start
The MAX8556 EV kit is fully assembled and tested.
Follow these steps to verify board operation:
1) Preset the power supply to 1.425V and turn off the
power supply.
Do not turn on the power supply
until all connections are made.
2) Verify that the shunt is across pins 2 and 3 of JU1 to
enable the device.
3) Connect the positive lead of the power supply to the
VIN pad on the EV kit, and the negative lead of the
power supply to the GND pad on the EV kit.
4) Connect the positive input of the DMM to the VOUT
pad on the EV kit, and the negative input of the
DMM to the GND pad on the EV kit to measure the
output voltage.
5) Turn on the power supply and verify that the output
voltage is 1.2V ±1%.
6) Sweep the input voltage from +1.425V to +3.6V.
Verify that the output voltage is 1.2V ±1% over the
entire input range.
7) Set the power supply to 2V.
8) Connect the 4A load between the VOUT and GND
pads on the EV kit.
9) Verify that the output voltage is 1.2V ±1%.
POK Output
The MAX8556 has an open-drain POK output that goes
high impedance after the output is within ±10% of the
regulation voltage. On the EV kit, R1 pulls up POK to
V
IN
. The MAX8556 EV kit can also be used to evaluate
the MAX8557. In this case, the POK output becomes
the POR output.
Shutdown
The MAX8556 features a shutdown mode to power
down the output and reduce input current. To shut
down the device, place the shunt between positions 1
and 2 of JU1. To operate normally, place the shunt
between positions 2 and 3 of JU1.
Jumper Settings
Table 1. Jumper JU1 Functions (EN)
SHUNT
LOCATION
1 and 2
2 and 3
EN CONNECTION
Connected to GND
Connected to VIN
OPERATION
Output disabled
Output enabled
2
_______________________________________________________________________________________
MAX8556 Evaluation Kit
Evaluates: MAX8556/MAX8557
VIN
1.425V TO 3.6V
C1
10µF
C2
10µF
1, 2, 3, 4, 5, 6
IN
OUT
U1
7, 8, 9, 10, 11
R2
1.4kΩ
0.1%
R3
1.0kΩ
0.1%
GND
N.C.
15
14
C3
10µF
VOUT
1.2V AT 4A
C4
10µF
GND
GND
R1
100kΩ
MAX8556ETE
FB
13
POK
3
JU1 2
1
12
16
POK
EN
Figure 1. MAX8556 EV Kit Schematic
Figure 2. MAX8556 EV Kit Component Placement Guide—Top
Silkscreen
Figure 3. MAX8556 EV Kit PC Board Layout—Component Side
_______________________________________________________________________________________
3
MAX8556 Evaluation Kit
Evaluates: MAX8556/MAX8557
Figure 4. MAX8556 EV Kit PC Board Layout—Layer 2
Figure 5. MAX8556 EV Kit PC Board Layout—Layer 3
Figure 6. MAX8556 EV Kit PC Board Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
4
_____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2004 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
聊聊、笑笑、闹闹
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
