REVISIONS
LTR
A
DESCRIPTION
Add radiation hardness requirements. Add table IIB. Add case outline H to
1.2.4, change 1.3 and figure 1 to include case H. – lgt
DATE (YR-MO-DA)
00-08-24
APPROVED
R. MONNIN
B
Make changes to pin 3 on case H as specified in figure 1 and long term
stability test as specified in table I. - ro
01-11-26
R. MONNIN
C
Add case outlines P and 2. Make changes to 1.2.4, 1.3, and figure 1. –rrp
02-04-22
R. MONNIN
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
PREPARED BY
Rick C. Officer
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
C
10
C
11
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
Charles E. Besore
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
APPROVED BY
Michael A. Frye
DRAWING APPROVAL DATE
90-01-11
MICROCIRCUIT, LINEAR, POSITIVE 10-VOLT
ADJUSTABLE PRECISION VOLTAGE
REFERENCE, MONOLITHIC SILICON
AMSC N/A
REVISION LEVEL
C
SIZE
A
SHEET
CAGE CODE
67268
1 OF
11
5962-89479
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
5962-E313-02
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and
M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the
Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the
PIN.
1.2 PIN. The PIN is as shown in the following examples.
For device classes M and Q:
5962
Federal
stock class
designator
\
-
RHA
designator
(see 1.2.1)
\/
Drawing number
For device class V:
5962
Federal
stock class
designator
\
R
RHA
designator
(see 1.2.1)
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and
are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
Generic number
REF10A
REF10B
Circuit function
Precision reference +10 volt adjustable output,
with guaranteed long-term stability
Precision reference +10 volt adjustable output,
with guaranteed long-term stability
89479
01
Device
type
(see 1.2.2)
V
Device
class
designator
(see 1.2.3)
G
Case
outline
(see 1.2.4)
X
Lead
finish
(see 1.2.5)
89479
01
Device
type
(see 1.2.2)
/
G
Case
outline
(see 1.2.4)
X
Lead
finish
(see 1.2.5)
/
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed
below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q
designators will not be included in the PIN and will not be marked on the device.
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant,
non-JAN class level B microcircuits in accordance with MIL-PRF-38535,
appendix A
Certification and qualification to MIL-PRF-38535
Q or V
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89479
SHEET
C
2
1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
G
H
P
2
Descriptive designator
MACY1-X8
GDFP1-F10 or CDFP2-F10
GDIP1-T8 or CDIP2-T8
CQCC1-N20
Terminals
8
10
8
20
Package style
Can
Flat pack
Dual-in-line
Square leadless chip carrier
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
1.3 Absolute maximum ratings. 1/
Input voltage (V
IN
) ........................................................................................................ 40 V dc
Power dissipation (P
D
) ................................................................................................. 500 mW 2/
Output short circuit duration ......................................................................................... Indefinite
Storage temperature range .......................................................................................... -65°C to +150°C
Lead temperature (soldering, 10 seconds) .................................................................. +300°C
Junction temperature (T
J
) ............................................................................................ +150°C
Thermal resistance, junction-to-case (θ
JC
) .................................................................. See MIL-STD-1835
Thermal resistance, junction-to-ambient (θ
JA
):
Case G .................................................................................................................... 150°C/W 2/
Case H .................................................................................................................... 180°C/W 2/
Case P .................................................................................................................... 148°C/W
Case 2 ..................................................................................................................... 95°C/W
1.4 Recommended operating conditions.
Input voltage (V
IN
)......................................................................................................... +15V
Ambient operating temperature range (T
A
) ................................................................... -55°C to +125°C
1.5 Radiation features.
Maximum total dose available (dose rate = 50 – 300 rads(Si) / s) ................................ 100 Krads(Si) 3/
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in
the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the
solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
______
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ For case G, derate above +80°C, 6.8 mW/°C. For case H, derate above +85°C, 5.6 mW/°C. For case P, derate above
+75°C, 6.6 mW/°C. For case 2, derate above +72°C, 7.8 mW/°C.
3/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883,
method 1019, condition A.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89479
SHEET
C
3
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 -
MIL-STD-1835 -
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be as specified on figure 2.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space
limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the
RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535.
Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89479
SHEET
C
4
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/ 2/
-55°C
≤
T
A
≤
+125°C
V
IN
= 15 V
unless otherwise specified
Quiescent supply current
I
SY
No load
1
2,3
M,D,P,L,R
Output adjustment range
∆
V
TRIM
R
P
= 10 kΩ,
T
A
= 25°C
Output voltage
V
OUT
I
L
= 0 mA
1
01
02
2,3
01
02
M,D,P,L,R
Short circuit current
Sink current
Load regulation
I
OS
I
S
LD reg
V
O
= 0 V
3/
I
L
= 0 mA to 10 mA
4/ 5/
3/
1
1
1
1
01
All
All
01
02
M,D,P,L,R
I
L
= 0 mA to 8 mA
4/ 5/
1
2, 3
01
01
02
Line regulation
LN reg
V
IN
= 13 V to 33 V
4/
1
2, 3
M,D,P,L,R
Load current 7/
I
L
3/ 6/
1
1
2, 3
Output voltage noise
Output voltage
temperature coefficient
Long term stability
∆
V
OUT
/
∆t
See footnotes at end of table.
Lot qualification test 3/ 8/
e
np-p
TCV
O
0.1 Hz to 10 Hz
3/ 7/
3/
4
5, 6
All
01
02
All
All
All
01
All
10
8
30
+8.5
+25
50
µVp-p
ppm /
°C
ppm/
1k hr
9.97
9.95
9.955
9.905
9.94
+15
-0.3
0.008
0.010
0.015
0.012
0.015
0.01
0.015
0.03
mA
%/V
% / mA
10.03
10.05
10.045
10.095
10.06
+60
mA
V
3/
1
1
01
All
±3.0
All
Min
Max
1.4
2.0
1.4
%
mA
Group A
subgroups
Device
type
Limits
Unit
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89479
SHEET
C
5
模拟电子
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
