SCOPE:
CMOS VIDEO MULTIPLEXER/AMPLIFIER
Generic Number
MAX453M(x)/883B
MAX455M(x)/883B
MAX452M(x)/883B
MAX454M(x)/883B
Device Type
01
02
03
04
Case Outline(s).
The case outlines shall be designated in Mil-Std-1835 and as follows:
Case Outline
Package Code
Outline Letter
Mil-Std-1835
JA
GDIP1-T8 or CDIP2-T8
8 LEAD CERDIP
J8
JD
GDIP1-T14 or CDIP2-T14
14 LEAD CERDIP
J14
LP
CQCC1-N20
20 Leadless Chip Carrier L20
Absolute Maximum Ratings
Total Supply Voltage (V+ to V-) ............................................................................ 12V
Positive Supply Voltage, V+ (rel. GND) .............................................................. +12V
Negative Supply Voltage, V- (rel. GND) .............................................................. -12V
Analog Input Voltages: ..........................................................(V+) +0.3V to (V-) -0.3V
Digital Input Voltages: ................................................................. -0.3V to (V+) +0.3V
Duration of Output Short-Circuit to ground ................................................... Indefinite
Input Current, power on or off:
Digital Inputs .............................................................................................
±20mA
All other pins .............................................................................................
±50mA
Short-Circuit Duration, T
OUT
........................................................................ Continuous
Lead Temperature (soldering, 10 seconds) ..................................................................... +300°C
Storage Temperature ........................................................................................ -65°C to +160°C
Continuous Power Dissipation ............................................................................. T
A
=+70°C
8 pin CERDIP(derate 8.0mW/°C above +70°C) ....................................................... 640mW
14 pin CERDIP(derate 9.1mW/°C above +70°C) ..................................................... 727mW
20 pin CERDIP(derate 11.1mW/°C above +70°C) .................................................... 889mW
20 pin LCC(derate 9.1mW/°C above +70°C) ............................................................ 727mW
Junction Temperature T
J
..............................................................................…........ +150°C
Thermal Resistance, Junction to Case,
ΘJC
8 pin CERDIP..................................................................................................... 55°C/W
14 pin CERDIP................................................................................................... 55°C/W
20 pin CERDIP................................................................................................... 40°C/W
20 pin LCC ........................................................................................................ 20°C/W
Thermal Resistance, Junction to Ambient,
ΘJA:
8 pin CERDIP.................................................................................................... 125°C/W
14 pin CERDIP.................................................................................................. 110°C/W
20 pin CERDIP................................................................................................... 90°C/W
20 pin LCC ...................................................................................................... 110°C/W
Recommended Operating Conditions
Ambient Operating Range (T
A
) ............................................................ -55°C to
+125°C
Input Voltage Range ....................................................................................... -2V to +2V
Operating Supply Voltage ...............................................................
±4.5Vdc
to
±5.5V
dc
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
----------------------------
Electrical Characteristics of MAX452/453/454/455/883B
for /883B and SMD 5962-94512
19-0207
Page 2 of
Rev. D
6
TABLE 1. ELECTRICAL TESTS:
CONDITIONS
-55
°C
<=T
A
<= +125°C 1/
Unless otherwise specified
Group A
Subgroup
TEST
VIDEO AMPLIFIER
Input Voltage Range
Input Offset Voltage
Input Bias Current
Open-Loop Voltage Gain
Symbol
Device
type
Limits
Min
Limits
Max
Units
V
IN
V
OS
IB
A
VOL
NOTE 2
R
L
=1000Ω
R
L
=150Ω
R
L
=75Ω
-2V≤V
IN
≤+2V
±4.5V
to
±5.5V
NOTE 3
AV=0dB, RL=75Ω, NOTE 3
AV=6dB, RL=150Ω, NOTE 3
1,2,3
1
2,3
1
2,3
1
All
All
All
All
-2.0
2.0
5.0
10.0
10
500
V
mV
nA
V/V
Common-Mode Rejection
Ratio
Power Supply Rejection
Ratio
Slew Rate
VIDEO AMPLIFIER
-3dB Bandwidth
Full-Scale Output Current
Output Voltage Swing
Input noise, dc to 40 MHz
Operating Supply Voltage
Supply Current
MULTIPLEXER
Input Voltage Range
OFF Input Leakage
Current
Logic Low Threshold
Logic High Threshold
Input Pullup/down
Current
Turn-On Time
Turn-Off Time
Break-Before-Make
Delay
Channel “On”
Capacitance
Channel “Off”
Capacitance
Channel “Off” Isolation
Delay
NOTE 1:
NOTE 2:
NOTE 3:
NOTE 4:
CMRR
PSRR
SR
GBW1
GBW2
I
OUT
V
OUT
Vn
V+, V-
I
CC
1
1
2,3
1
1
1
1
1
1,2,3
1
2,3
1,2,3
1
2,3
1,2,3
1,2,3
1
9
9
9
9
9
All
All
All
All
All
All
All
All
All
180
45
25
60
54
48
150
30
25
±14
±2.1
±4.5
20
17
-2.0
0.5
±5.5
30
32
2.0
10
500
0.8
20
120
60
10
15
12
dB
dB
V/µs
MHz
mA
V
mVrms
V
mA
NOTE 3
V
IN
=0V
V
IN
I
OFF
V
IL
V
IH
I
IL
/I
IH
t
ON
t
OFF
t
D
C
ON
C
OFF
OIRR
NOTE 4
02,03,04
02,03,04
02,03,04
02,03,04
02,03,04
02,03,04
02,03,04
02,03,04
02,03,04
02,03,04
02,03,04
V
nA
V
V
µA
ns
ns
ns
pF
pF
2.4
NOTE 3
NOTE 3
NOTE 3
NOTE 3
NOTE 3
9
fIN=4MHz, RS=75Ω, NOTE 3,
Channel 2 to Channel 3
All other channels
V+=+5V, V-=-5V, -2V≤V
IN
≤+2V,
Output Load Resistor=150Ω.
Input bias includes the multiplexer’s On-state leakage current.
Guaranteed by design.
Guaranteed over the voltage range, V-≤V
IN
≤V+
45
60
dB
----------------------------
Electrical Characteristics of MAX452/453/454/455/883B
for /883B and SMD 5962-94512
19-0207
Page 3 of
Rev. D
6
QUALITY ASSURANCE
Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-
Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125°C minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,
C, and D inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883:
1. Test condition A, B, C, D.
2. TA = +125°C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2.
ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements
Subgroups
per Method 5005, Table 1
1
1*, 2, 3, 9**
1, 2, 3, 9**
1
Interim Electric Parameters
Method 5004
Final Electrical Parameters
Method 5005
Group A Test Requirements
Method 5005
Group C and D End-Point Electrical Parameters
Method 5005
*
**
PDA applies to Subgroup 1 only.
Guaranteed by design.
----------------------------
Electrical Characteristics of MAX452/453/454/455/883B
for /883B and SMD 5962-94512
19-0207
Page 5 of
Rev. D
6
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
