SW
-I
O
PM
M
IP series
Pushbutton switches for harsh environments •
bushing Ø 12 mm • momentary
DISTINCTIVE FEATURES
Illuminated or non-illuminated
Tactile feedback
Wide variety of configurations
Flat round actuator for optional marking
Sealed to IP67 and IP69K
ENVIRONMENTAL SPECIFICATIONS
• Front panel sealing: IP67 according to IEC 60529
IP69K according to DIN 40050-9 (non-illuminated) with cap U5125
• Shock resistance: 100 g according to IEC 512-4, test 6c
• Vibration resistance: 10-500Hz - 10 g according to IEC 512-4, test 6d
• Salt spray: IEC 512-6, test 11f
• Robustness (non-illuminated): IK06 according to EN 62262 (1 joule)
• Operating temperature: -40 °C to +85 °C (-40 °F to +185 °F)
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load (gold plated silver
contacts):
5 A 28 VDC, 70,000 cycles (only function 3)
For W terminals, current has
0.2 A 48 VDC, 500,000 cycles
to be limited to 400 mA.
0.5 A 48 VAC, 500,000 cycles
• Initial contact resistance: 100 mΩ max.
• Insulation resistance: 1 GΩ min. at 500 VDC
• Dielectric strength: 1,500 Vrms
• Contact bounce: 10 ms
LED COMPONENT SPECIFICATIONS
LED color
Super red (L0S)
Yellow (L0Y)
Green (L0G)
Blue (L0B)
White (L0W)
Red/green (LSG)
Yellow/green (LYG)
Forward current
20 mA
20 mA
20 mA
20 mA
20 mA
20 mA
20 mA
Typ. forward voltage
2.1 V
2.1 V
2.1 V
3.2 V
3.35 V
Red: 1.95 V / green: 2.1 V
Yellow: 2 V / green: 2.1 V
Max. forward voltage
2.3 V
2.3 V
2.3 V
3.8 V
4.25 V
2.5 V
2.5 V
A resistor must be series-connected by the user.
Resistor value = supply voltage - LED forward voltage
LED forward current
The company reserves the right to change specifications without notice.
1
PANEL SWITCHES
7
-1
09
PANEL SWITCHES
IP series
Pushbutton switches for harsh environments •
bushing Ø 12 mm • momentary
GENERAL SPECIFICATIONS
• Panel thickness: 1.5 mm (.059) min.
4 mm (.157 max.)
• Total travel:
Function 3: 1.7 mm (.067) ± 0.3 mm (0.012)
Function 5: 1.3 mm (.051) ± 0.3 mm (0.012)
• Typical operating force: 6 N ± 2 N
• Low level/mech. life: 1,000,000 cycles
• Torque: 1.5 Nm max. applied to nut
• Soldering: 320 °C (608 °F) max. for 3 sec.
2.40
(.094)
8.70
(.342)
5.20
(.204)
5.20
(.204)
4.55
(.179)
4.55
(.179)
8.70
(.342)
2.40
(.094)
TERMINALS
ILLUMINATED MODELS
LED
Cathode
(-)
LED
Cathode
(-)
Solder lug
S
Straight
P
NON-ILLUMINATED MODELS
1.00
1.00
(.039) (.039)
2.80
2.80
(.110) (.110)
1.20
1.20
(.047) (.047)
MATERIALS
• Case: thermoplastic UL94-V0
• Actuator: polyamide 6/6
• Bushing/bezel: zinc die-cast (zamak), black painted
• Contacts: - silver, gold plated (std)
- brass, gold plated (for option 104)
• Output wires (flying lead terminals):
F version:
AWG20, section 0.6 mm
2
W version:
AWG24, section 0.23 mm
2
• LED wires:
F version:
AWG26, section 0.12 mm
2
W version:
AWG24, section 0.23 mm
2
• Lens: polycarbonate
• Terminal seal: epoxy
Straight
P
Quick-connect
Z1
CIPCOSP
CIPCOSP
ELECTRICAL FUNCTIONS
NON-ILLUMINATED MODELS
CIPCOSZ1
CIPCOSZ1
ILLUMINATED MODELS
Function 3 (NO)
Function 3 (NO)
Function 5 (NC/NO)
MOUNTING
1.50min-4Max
(.059 min-.157max)
Ø13.50
(.531DIA)
17.50
(.688)
CIPCE1
PANEL CUT-OUT
12.90
(.507)
AGENCY APPROVAL
2 A 125 VAC/250 VAC
File E83438
See following pages.
Ø13.60
(.535DIA)
1
MATRIX MOUNTING - BACK OF PANEL SPACE REQUIREMENT
20.00
(.787)
20.00
(.787)
2
20.00
(.787)
IP series
Pushbutton switches for harsh environments •
bushing Ø 12 mm • momentary
BUILD YOUR PART NUMBER
BASIC PART NUMBER
IP
SERIES
ACTUATOR SHAPES
ELECTRICAL FUNCTIONS
TERMINALS
CONTACTS
B
C
R
P
Round, curved,
shiny
Square
Round, curved
Round, flat
3
5
Normally open
(NO)
NC/NO combined
(non-illuminated)
S
F
W
P
Z1
Solder lugs
Flying leads, standard
Flying leads, thin
Straight PC
Quick-connect
(non-ill., NO only )
AD
CD
Silver, gold
plated (standard)
Brass, gold
plated (option 104)
Actuator marking
available on round flat
models (symbol 10 mm
max.). On request.
OPTIONS
ACTUATOR COLORS
LED COLORS
OPTIONS
APPROVAL
1
B
2
3
4
5
6
7/1
8
9
Blue
Dark blue
Black
Green
Grey
Yellow
Red
White
Bright chrome
Orange
Blank
L0S
L0Y
L0G
L0B
L0W
LSG
LYG
Non-illuminated
Super red
Yellow
Green
Blue
White
Red/green
Yellow/green
100
101
104
Satin chrome
bezel
Bright chrome
bezel
High actuator
(non-illum. round
models only)
UL
Consult factory for
detail of approved
models.
Option 104
If combined with electrical
function 5 (NC/NO), this
option should be ordered
with CD contacts (brass, gold
plated). Current/voltage
rating: 100 mA 30 VDC
ABOUT THIS SERIES
On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart.
Notice:
please note that not all combinations of above numbers are available. Refer to the following pages for further information.
A sealing boot
is available to protect the switches against frost and sand. See "Sealing Boots" section of website.
Mounting accessories:
Standard hardware supplied: 1 hex nut 14 mm (.551) across flats and 1 O-ring. Hex nut part number U166.
3
PANEL SWITCHES
PANEL SWITCHES
IP series
Pushbutton switches for harsh environments •
bushing Ø 12 mm • momentary
SQUARE - ILLUMINATED
SOLDER LUG TERMINALS
FLAT
5.00
(.196)
1.50 Min
(.059 Min)
2.00
(.078)
12.00
(.472SQ)
17.50
(.688SQ)
6.40 6.80
(.251) (.267)
IPC3SAD
Normally Open
Ø12.00x0.75SI
(.472DIAx0.75IS)
6.10
(.240)
EPOXY
5.20
(.204)
2.00
(.078)
1.50
(.059)
1.20
(.047)
2.00
(.078)
0.40
(.015)
5.08
(.200)
Also available with straight PC terminals:
IPC3PAD
LED color is indicated by the bottom of the switch.
5.00
(.196)
SQUARE - ILLUMINATED
FLYING LEAD TERMINALS
FLAT
12.00
(.472SQ)
1.50 Min
(.059 Min)
17.50
(.688SQ)
6.80
(.267)
IPC3FAD
Normally Open
16.00 Max
(.629 Max)
Ø12.00x0.75SI
(.472DIAx0.75IS)
For THIN flying leads, replace F with W.
Wire colors:
black: NO contact, red: LED anode(+), blue: LED cathode(-)
Shown with standard flying lead terminals.
5.00
(.196)
1.50 Min
(.059 Min)
2.00
(.078)
SQUARE - NON ILLUMINATED
SOLDER LUG TERMINALS
Normally Open
FLAT
12.00
(.472SQ)
500±10
(19.68±.393)
17.50
(.688SQ)
6.40 6.80
(.251) (.267)
IPC3SAD
IPC5SAD
Ø12.00x0.75SI
(.472DIAx0.75IS)
6.10
(.240)
Normally Open
EPOXY
5.20
(.204)
2.00
(.078)
1.50
(.059)
1.20
(.047)
2.00
(.078)
0.40
(.015)
5.08
(.200)
Also available with straight PC terminals:
IPC3PAD
(NO) or
IPC5PAD
(NC/NO)
and quick-connect terminals:
IPC3Z1AD
(NO only)
5.00
(.196)
1.50 Min
(.059 Min)
SQUARE - NON ILLUMINATED
FLYING LEAD TERMINALS
Normally Open
FLAT
12.00
(.472SQ)
17.50
(.688SQ)
IPC3FAD
IPC5FAD
6.80
(.267)
NC/NO combined
16.00 Max
(.629 Max)
Ø12.00x0.75SI
(.472DIAx0.75IS)
For THIN flying leads, replace F with W.
Wire colors
(NC/NO): black: NO, blue: NC.
Shown with standard flying lead terminals.
4
NO
500±10
(19.68±.393)
NC/NO
IP series
Pushbutton switches for harsh environments •
bushing Ø 12 mm • momentary
ROUND - ILLUMINATED
SOLDER LUG TERMINALS
5.00
(.196)
FLAT
1.50 Min
(.059 Min)
2.00
(.078)
Ø12.00
(.472DIA)
Ø17.50
(.688DIA)
IPR3SAD
Normally Open
6.40 6.80
(.251) (.267)
Ø12.00x0.75SI
(.472DIAx0.75IS)
6.10
(.240)
EPOXY
5.20
(.204)
0.40
(.015)
5.08
(.200)
1.50
(.059)
1.20
(.047)
2.00
(.078)
Also available with straight PC terminals:
IPR3PAD
LED colour is indicated by the bottom of the switch.
5.00
(.196)
1.50 Min
(.059 Min)
ROUND - ILLUMINATED
FLYING LEAD TERMINALS
FLAT
2.00
(.078)
Ø12.00
(.472DIA)
Ø17.50
(.688DIA)
6.80
(.267)
IPR3FAD
16.00 Max
(.629 Max)
Normally Open
Ø12.00x0.75SI
(.472DIAx0.75IS)
For THIN flying leads, replace F with W.
Wire colors:
black: NO contact, red: LED anode(+), blue: LED cathode(-)
Shown with standard flying lead terminals.
5.00
(.196)
Curved actuator, NO
Curved actuator, NC/NO
Flat actuator, NO
Flat actuator, NC/NO
IPR3SAD
IPR5SAD
IPP3SAD
1.50
(.059)
6.40 6.80
(.251) (.267)
Ø12.00x0.75SI
(.472DIAx0.75IS)
NO
EPOXY
1.20
(.047)
2.00
(.078)
NO
NC
0.40
(.015)
5.08
(.200)
NO
1.50 Min
(.059 Min)
IPP5SAD
NC/NO
Also available with straight PC terminals:
IPC3PAD
(NO) or
IPC5PAD
(NC/NO)
and quick-connect terminals:
IPC3Z1AD
(NO only)
5.00
(.196)
6.80
(.267)
Curved actuator, NO
Curved actuator, NC/NO
Flat actuator, NO
Flat actuator, NC/NO
For THIN flying leads, replace F with W.
Wire colors
(NC/NO): black: NO, blue: NC
Shown with standard flying lead terminals.
IPR3FAD
IPR5FAD
IPP3FAD
IPP5FAD
Ø12.00x0.75SI
(.472DIAx0.75IS)
13.20
(.519)
NO
500±10
(19.68±.393)
1.50 Min
(.059 Min)
NC/NO
2.00
(.078)
ROUND - NON ILLUMINATED
FLYING LEAD TERMINALS
FLAT
Ø12.00
(.472DIA)
Ø17.50
(.688DIA)
5.20
(.204)
2.00
(.078)
ROUND - NON ILLUMINATED
SOLDER LUG TERMINALS
FLAT
Ø12.00
(.472DIA)
Ø17.50
(.688DIA)
500±10
(19.68±.393)
5
PANEL SWITCHES
B1
DIY/开源硬件专区
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
