IHS series
Hall effect pushbutton switches - bushing Ø 12 mm - momentary
Distinctive features and specifications
UG1410A
K
Momentary pushbutton (NO)
K
5 million cycles
K
Low behind-panel depth
K
Standard and high actuator
K
Sealed to IP67
B1
ENVIRONMENTAL SPECIFICATIONS
GENERAL SPECIFICATIONS
• Front panel sealing : IP67 according to IEC 60529
• Operating temperature : -40°C to +85°C
ELECTRICAL SPECIFICATIONS
• Panel thickness : 1,5 mm (.059) min.
4 mm (.157) max.
• Total travel : 1,80 mm (.070)
+/- 0,3 mm
• Supply voltage : 3,5VDC to 24VDC
• Supply current : VDC = 12V : 2,5mA Typ. to 5mA max.
(current consumption in OFF position)
• Max. output current : 50mA
• Max. output voltage : 24VDC
• Output type : NPN
• Typical operating force : 6N
+/- 2N
• Mechanical life : 5 million cycles
• Torque : 1,5 Nm max. applied to nut
MATERIALS
WIRING DIAGRAM
VDD
RED wire
+Vout
• Case : PBT, UL94-V0
• Actuator : polyamide 6/6
• Bushing/bezel : zinc die-cast
(zamac), black painted
• Multi-wire lead : AWG26, 150 mm
LOAD
OUTPUT
WHITE wire
GND
BLACK wire
MOUNTING
Panel cut-out
12.90
(.507)
O-ring
1.50min-4Max
(.059 min-.157max)
Matrix mounting
20.00
(.787)
20.00
(.787)
Back of panel space requirement
1
Ø13.60
(.535DIA)
Ø13.50
(.531DIA)
The company reserves the right to change specifications without notice.
APEM
www.apem.com
B1-29
20.00
(.787)
14.50
(.570)
IHS series
Hall effect pushbutton switches - bushing Ø 12 mm - momentary
Overview
IHS
SERIES
Actuator shapes
R
H
Round
Round, high
3
Electrical function
Normally open
(NO)
6
Operating force
6N
F
Terminals
Flying leads
B1
Actuator colours
1
2
3
4
5
6
7
9
B
Blue
Black
Green
Grey
Yellow
Red
White
Orange
Dark blue
Options
Blank
None
100
Satin chrome bezel
101
Bright chrome bezel
ABOUT THIS SERIES
On the following pages, you will find successively :
model structure of switches and options in the same order as in above chart
Dimensions :
first dimensions are in mm while inches are shown as bracketed numbers.
: please note that not all combinations of above numbers are available.
Refer to the following pages for further information.
NOTICE
A sealing boot
is available to protect the switches against frost and sand (P/N U5125). It is presented after the IA series
and in section H.
Mounting accessories
: Standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 O-ring.
Hex nut part number U166.
Packaging unit
: 25 pieces
B1-30
www.apem.com
APEM
IHS series
Hall effect pushbutton switches - bushing Ø 12 mm - momentary
Round - non-illuminated
• Standard or high actuator
Function 3 (NO)
MODEL
STRUCTURE
B1
©
Flat
5.00
(.196)
1.50 Min
(.059 Min)
2.00
(.078)
Ø12.00
(.472DIA)
Ø17.50
(.688DIA)
Standard actuator
IHSR36F
Normally Open
6.40 6.80
(.251) (.267)
Ø12.00x0.75SI
(.472DIAx0.75IS)
High actuator
©
Flat
5.00
(.196)
1.50 Min
(.059 Min)
4.70
(.185)
Ø12.00
(.472DIA)
Ø17.50
(.688DIA)
6.40 6.80
(.251) (.267)
IHSH36F
Normally Open
Ø12.00x0.75SI
(.472DIAx0.75IS)
ACTUATOR COLOURS
1
: blue -
2
: black -
3
: green -
4
: grey -
5
: yellow -
6
: red -
7
: white -
9
: orange -
B
: dark blue
OPTIONS
100
: Satin chrome bezel
101
: Bright chrome bezel
APEM
www.apem.com
150.00
(5.905)
150.00
(5.905)
B1-31
IHL series
Hall effect pushbutton switches - bushing Ø 12 mm - linear
Distinctive features and specifications
K
Linear output pushbutton
K
0,5 to 4,5 volt output
K
Different operating force
K
5 million cycles
K
Sealed to IP67
B1
ENVIRONMENTAL SPECIFICATIONS
GENERAL SPECIFICATIONS
• Front panel sealing : IP67 according to IEC 60529
• Operating temperature : -40°C to +85°C
• EMC testing : 10V per meter extend to radiated fields in freq. range of
80 Mhz to 1.000 MHz. 1KHz 80 % sine wave modulation according to
IEC/EN 61000-4-3
ELECTRICAL SPECIFICATIONS
• Panel thickness : 1,5 mm (.059) min.
10 mm (.393) max.
• Total travel : 4 mm (.160)
+/- 0,3 mm
• Mechanical life : 5 million cycles
• Torque : 1 Nm max. applied to nut
MATERIALS
• Supply voltage : 4,5VDC to 5,5VDC without regulator
6,5VDC to 24VDC with 5V regulator
• Supply current : 9mA max.
• Max. output current : 1,25mA
• Max. output voltage with or without regulator : see graph below.
• Case : PA46, UL94-V0
• Actuator : polyamide 6/6
• Bushing : polyamide 6/6
• Multi-wire lead : AWG26, 150 mm
LINEAR OUTPUT GRAPH (VDC = 5V@20°C)
WIRING DIAGRAM
VDD
RED wire
OUTPUT
WHITE wire
GND
BLACK wire
MOUNTING
Panel cut-out
12.90
(.507)
O-ring
0.40min-0.50Max
(.016MIN.-.020MAX.)
1.50min-10.00Max
(.059MIN.-.393MAX.)
Matrix mounting
17.50
(.689)
17.50
(.689)
Back of panel space requirement
Ø13.60
(.535DIA)
Ø15.60
(.614DIA)
Ø13.50
(.531DIA)
B1-32
www.apem.com
17.50
(.689)
17.50
(.689)
2
APEM
IHL series
Hall effect pushbutton switches - bushing Ø 12 mm - linear
Overview
IHL
SERIES
Actuator shape
R
Round
3
5
Operating force
Soft
Standard
(progressive from
1N to 3,5N)
Hard
F
Terminals
Flying leads
Output voltage
01
0,5 to 4,5 V
Other : on request.
7
Regulator
X
5
None
5V regulator
Other : on request
B1
Actuator colours
1
2
3
4
5
6
7
9
B
Blue
Black
Green
Grey
Yellow
Red
White
Orange
Dark blue
ABOUT THIS SERIES
On the following pages, you will find successively :
model structure of switches and options in the same order as in above chart
Dimensions :
first dimensions are in mm while inches are shown as bracketed numbers.
: please note that not all combinations of above numbers are available.
Refer to the following pages for further information.
NOTICE
Mounting accessories
: Standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 O-ring.
Hex nut part number U166.
Packaging unit
: 25 pieces
APEM
www.apem.com
B1-33