CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1.
θ
JA
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2.
θ
JA
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
3. For
θ
JC
, the “case temp” location is the center of the exposed metal pad on the package underside.
4. Jedec Class II pulse conditions and failure criterion used. Level B exceptions are: using a max positive pulse of 6.5V on the SHDN pin, and using
a max negative pulse of -0.8V for all pins.
Analog Specifications
SYMBOL
R
TOTAL
Over recommended operating conditions, unless otherwise stated.
TEST CONDITIONS
W option
U option
MIN
(Note 22)
TYP
(Note 5)
10
50
-20
±50
±80
0
70
10/10/25
Voltage at pin from GND to V
CC
0.1
1
V
CC
200
+20
MAX
(Note 22)
UNIT
kΩ
kΩ
%
ppm/°C
(Note 21)
ppm/°C
(Note 21)
V
Ω
pF
µA
PARAMETER
R
H
to R
L
Resistance
R
H
to R
L
Resistance Tolerance
End-to-End Temperature Coefficient
W and U option
W option
U option
V
RH
, V
RL
R
W
C
H
/C
L
/C
W
(Note 21)
I
LkgDCP
V
RH
and V
RL
Terminal Voltages
Wiper Resistance
Potentiometer Capacitance
Leakage on DCP Pins
V
RH
and V
RL
to GND
V
CC
= 3.3V, wiper current = V
CC
/R
TOTAL
VOLTAGE DIVIDER MODE
(0V @ R
L
i; V
CC
@ R
H
i; measured at R
W
i, unloaded; i = 0 or 1)
INL
(Note 10)
DNL
(Note 9)
ZSerror
(Note 7)
Integral Non-linearity
Differential Non-linearity
Zero-scale Error
Monotonic over all tap positions, W and U
options
Monotonic over all tap positions, W and U
options
W option
U option
FSerror
(Note 8)
Full-scale Error
W option
U option
-1
-0.5
0
0
-5
-2
1
0.5
-1
-1
1
0.5
5
2
0
0
LSB
(Note 6)
LSB
(Note 6)
LSB
(Note 6)
LSB
(Note 6)
LSB
(Note 6)
LSB
(Note 6)
3
FN6180.2
September 8, 2009
ISL22426
Analog Specifications
SYMBOL
V
MATCH
(Note 11)
TC
V
(Note 12)
Over recommended operating conditions, unless otherwise stated.
(Continued)
TEST CONDITIONS
Any two DCPs at same tap position, same
voltage at all R
H
terminals, and same voltage
at all R
L
terminals
DCP register set to 40 hex
MIN
(Note 22)
-2
TYP
(Note 5)
MAX
(Note 22)
2
UNIT
LSB
(Note 6)
ppm/°C
PARAMETER
DCP to DCP Matching
Ratiometric Temperature Coefficient
±4
RESISTOR MODE
(Measurements between R
W
i and R
L
i with R
H
i not connected, or between R
W
i and R
H
i with R
L
i not connected; i = 0 or 1)
RINL
(Note 16)
RDNL
(Note 15)
Integral Non-linearity
Differential Non-linearity
DCP register set between 10h and 7Fh;
monotonic over all tap positions
DCP register set between 10h and 7Fh;
monotonic over all tap positions, W option
DCP register set between 10h and 7Fh;
monotonic over all tap positions, U option
Roffset
(Note 14)
Offset
W option
U option
R
MATCH
(Note 17)
DCP to DCP Matching
Any two DCPs at the same tap position with
the same terminal voltages
-1
-1
-0.5
0
0
-2
1
0.5
1
1
0.5
7
2
2
MI
(Note 13)
MI
(Note 13)
MI
(Note 13)
MI
(Note 13)
MI
(Note 13)
MI
(Note 13)
Operating Specifications
Over the recommended operating conditions, unless otherwise specified.
SYMBOL
I
CC1
I
CC2
I
SB
PARAMETER
V
CC
Supply Current (Volatile
Write/Read)
V
CC
Supply Current (Non-volatile
Write/Read)
V
CC
Current (Standby)
TEST CONDITIONS
f
SCK
= 5MHz; (for SPI Active, Read and
Volatile Write states only)
f
SCK
= 5MHz; (for SPI Active, Read and
Non-volatile Write states only)
V
CC
= +5.5V @ +85°C, SPI interface in
standby state
V
CC
= +5.5V @ +125°C, SPI interface in
standby state
V
CC
= +3.6V @ +85°C, SPI interface in
standby state
V
CC
= +3.6V @ +125°C, SPI interface in
standby state
I
SD
V
CC
Current (Shutdown)
V
CC
= +5.5V @ +85°C, SPI interface in
standby state
V
CC
= +5.5V @ +125°C, SPI interface in
standby state
V
CC
= +3.6V @ +85°C, SPI interface in
standby state
V
CC
= +3.6V @ +125°C, SPI interface in
standby state
I
LkgDig
t
WRT
(Note 21)
Leakage Current, at Pins SHDN, SCK, Voltage at pin from GND to V
CC
SDI, SDO and CS
Wiper Response Time After SPI Write
to WR Register
-1
MIN
(Note 22)
TYP
(Note 5)
MAX
(Note 22)
0.5
UNIT
mA
3
mA
5
µA
7
µA
3
µA
5
µA
3
µA
5
µA
2
µA
4
µA
1
µA
1.5
µs
4
FN6180.2
September 8, 2009
ISL22426
Operating Specifications
Over the recommended operating conditions, unless otherwise specified.
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
