UTC TA31002A LINEAR INTEGRATED CIRCUIT
TELEPHONE TONE RINGER
DESCRIPTION
The UTC TA31002A is a bipolar integrated circuit
designed for telephone bell replacement. It can also be
used as alarms or other alerting devices.
FEATURES
*Designed for telephone bell replacement.
*Low current drain for multiple extension of lines.
*Adjustable 2-frequency tone.
*Adjustable warbling rate.
*Built-in hysteresis prevents false triggering and
rotary dial 'CHIRPS'.
*Programmable for initiation current by simple
external resistor
DIP-8
PIN CONFIGURATIONS
Vcc
1
2
3
4
8
7
6
5
Output
High Freq.
Time Constant
High Freq.
Time Constant
GND
RSL
Low Freq.
Time Constant
Low Freq.
Time Costant
ABSOLUTE MAXIMUM RATINGS
(Ta=25°C )
PARAMETER
Supply Voltage
Power Dissipation
Operating Temperature
Storage Temperature
SYMBOL
Vcc
Pd
Topr
Tstg
VALUE
30
400
-45 to 85
-65 to 150
UNIT
V
mW
°C
°C
UTC
UNISONIC TECHNOLOGIES CO., LTD.
1
UTC TA31002A LINEAR INTEGRATED CIRCUIT
BLOCK DIAGRAM
R2
C3
R3
4
7
6
3
C2
LOW
OSC
HIGH
OSC
AMP
8
OUTPUT
1
POWER SUPPLY (WITH HYSTERESIS)
5
2
Note:R2,R3,C2 and C3 are parts externally mounted
ELECTRICAL CHARACTERISTICS
( Ta=25°C, all voltage referenced to GND unless otherwise specified)
PARAMETER
Operating Supply Voltage
Initiation Supply Voltage (note 1)
Initiation Supply Current (note 1)
Sustaining Voltage (note 2)
Sustaining Current (note 2)
Output Voltage High
Output Voltage Low
I
IN
(Pin 3)
I
IN
(Pin 7)
High Frequency 1
High Frequency 2
Low Frequency
SYMBOL
Vcc
Vsi
Isi
Vsus
Isus
VOH
VOL
TEST CONDITIONS
See Fig.2
6.8K-Pin 2 to GND
See Fig.2
No Load Vcc=Vsus,See Fig.2
Vcc=21V, I8=-15mA
Pin6=6V, Pin7=GND
Vcc=21V, I8=15mA
Pin6=GND, Pin7=6V
Pin3=6V, Pin4=GND
Pin7=6V, Pin6=GND
R3=191K, C3=6800pF
R3=191K, C3=6800pF
R2=165K, C2=0.47µF
MIN
17
1.4
9.7
0.7
17.0
TYP
19
2.8
11.0
1.4
19.0
MAX
29.0
21
4.2
12.0
2.5
21.0
1.6
500
500
563
704
11.0
UNIT
V
V
mA
V
mA
V
V
nA
nA
Hz
Hz
Hz
FH1
FH2
FL
461
576
9.0
512
640
10
*NOTE (See electrical characteristics sheet)
1. Initiation supply voltage (Vsi) is the supply voltage required to start the tone ringer oscillating.
2. Sustaining voltage (Vsus) is the supply voltage required to maintain oscillation.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
2
UTC TA31002A LINEAR INTEGRATED CIRCUIT
APPLICATION NOTE
The application circuit illustrates the use of the
UTCTA31002A device in typical telephone tone ringer
application.
The AC ringer signal voltage appears
across the TIP and RING inputs of the circuit and
is attenua-
ted by capacitor C1 and resistor R1.
C1 also provides isolation from DC voltage (48V)
on the exchanged line.
After full wave rectification by the bridge
diode, the wave form is filtered by capacitor C4 to
provide a DC supply for the tone ringer chip.
As this voltage exceeds the initiation voltage (Vsi),
oscillation starts.
With the components shown , the output frequency
chops between 512Hz (F
H1
) and 640 Hz(F
H2
)
at a 10 Hz(F
L
) rate.
The loudspeaker load is coupled through a 1300Ω
to 8Ω transformer.
The output coupling capacitor C5 is required with
transformer coupled loads.
When driving a pizeo-ceramic transducer type load,
the coupling C5 and transformer (1300Ω:8Ω) are
not required.
However, a current limiting resistor is required.
The low frequency oscillator oscillates at a rate (F
L
)
controlled by an external resistor (R2) and capacitor
(C2).
The fequency can be determined using the relation
F
L
=1/1.289 R2* C2. The high frequency oscillates
at a FH1,F
H2
controlled by an external resistor (R3)
and capacitor (C3). The frequency can be determined
using the relation F
H1
=1/1.504 R3*C3 and F
H2
=
1/1.203 R3*C3.
Pin 2 of the UTC TA31002A allows connection of
external resistor RSL, which is used to program the
slope of the supply current vs. supply voltage
characteristics (see Fig.3), and hence the supply
current up to the initiation voltage (Vsi). This initiation
voltage remains constant independent of RSL.
The supply current drawn prior to triggering varies
inversely with RSL, decreasing for increasing value
of resistance. Thus, increasing the value of RSL, will
decrease the amount of AC ringing current required to
trigger the device. As such, longer sucribser loops are
possible since less voltage is dropped per unit length of
loop wire due to the lower current level. RSL can
also be used to compensated for smaller AC coupling
capacitors (C5 on Fig.4) (higher impedance) to the
line which can be used to alter the ringer
equivalence
number of a tone ringer circuit.
The graph in Fig.3 illustrates the variation of supply
current with supply voltage of the
UTC
TA31002A.
Three curves are drawn to show the variation of
initiation current with RSL. Curve B ( RSL=6.8K)
shows the I-V characteristic for UTC TA31002A
tone ringer. Curve A is a plot with RSL<6.8KΩ
and shows an increase in the current drawn up to the
initiation voltage Vsi. The I-V characteristic after
initiation remains unchanged. Curve C illustrates the
effect of increasing
RSL above 6.8K
initiation current decreases but again current
alter triggering is unchanged.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
3
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
