Easy to check the fillet after soldering is finished.
2) Small, light, rectangular 4-chip network
Area ratio is 65% smaller than that of MNR34, while weight ratio has been cut 75%.
3) High-density mounting
Can be mounted even more densely than four 0603 chips (MCR03), and mounting costs are lower.
4) Compatible with a wide range of mounting equipment.
Squared coners make it excellent for mounting using image recognition machines.
5) ROHM resistors have approved ISO-9001 certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with
the product before using or ordering it.
Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
POWER LOAD (%)
Specifications
0.063W (1 / 16W)
at 70°C
80
60
40
20
0
−55
0
70
100
125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the limiting element voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E=
P×R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
Operating temperature
See Table 1.
−55°C
to
+125°C
Limiting element voltage
50V
Jumper type
Resistance
Rated current
Max. 50mΩ
1A
Table 1
Resistance tolerance
J
(±
5%)
Resistance range
(Ω)
2.2≤R≤6.8 (E6)
10≤R≤1M (E24)
F
(±
1%)
10≤R≤1M (E24)
Resistance temperature coefficient
(ppm /
°C)
±500
±200
±100
Operating temperature
−55°C
to
+125°C
•Before
using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
Rev.C
1/4
MNR14
Resistors
Characteristics
Item
Resistance
Variation of resistance
with temperature
Overload
±
(2.0%+0.1Ω)
Guaranteed value
Resistor type
Jumper type
J :
±5%
F :
±1%
Max. 50mΩ
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
JIS C 5201-1 4.8
Measurement :
−55
/
+25
/
+125°C
JIS C 5201-1 4.13
Rated voltage (current)
×2.5,
2s.
Maximum Overload Voltage : 100V
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. :
−55°C
to
+125°C
5cyc
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON
−
0.5h : OFF
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.3
125°C
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
JIS C 5201-1 4.33
See Table.1
Max. 50mΩ
Solderability
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
±
(1.0%+0.05Ω)
Max. 50mΩ
No remarkable abnormality on the appearance.
±
(1.0%+0.05Ω)
±
(3.0%+0.1Ω)
Max. 50mΩ
Max. 100mΩ
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
±
(3.0%+0.1Ω)
Endurance at 70°C
±
(3.0%+0.1Ω)
Endurance
±
(1.0%+0.05Ω)
Resistance to solvent
Max. 100mΩ
Max. 100mΩ
Max. 50mΩ
Bend strength of
the end face plating
Max. 50mΩ
±
(1.0%+0.05Ω)
Without mechanical damage such as breaks.
Dimensions
(Unit : mm)
0.6±0.15
0.4±0.15
0.3±0.2
Material
1
0.25±0.15
0.3±0.2
0.3±0.2
103
0.8
3.2±0.1
0.5±0.1
1.6±0.1
Thick dielectric glaze of oxide metal
(only silver used for jumper)
Thick film of silver for electrode
Nickel-coated electrode
External electrode coated with Sn
Alumina substrate
Overcoating
2
3
4
5
6
2
3
4
Cross section A-A'
6
1
5
Cross section B-B'
6 1
∗
Marking may change to the one-character type.
∗∗
Pitch of the upper electrode.
5
Rev.C
2/4
MNR14
Resistors
Equivalent circuit
R1
R2
R3
R4
R1=R2=R3=R4
Packaging
Reel
Taping
P
0
P
2
P
1
φD
0
E
F
B
0
08
06
04
02
02
04
06
08
W
A
B
D
A
0
Heat crimp cover / Tape
Chip network
Thick paper (Underside paper tape) resistors
Square punchout hole
mount
T2
C
Label
EIAJ ET-7200B compliant
(Unit : mm)
W
8.0
±
0.3
D
0
F
3.5
±
0.05
P
0
4.0
±
0.1
E
1.75
±
0.1
P
1
4.0
±
0.1
A
0
1.8
±
0.1
P
2
2.0
±
0.05
B
0
3.4
±
0.1
T
2
Max. 1.1
(Unit : mm)
A
B
C
D
φ13±0.2
0
φ180 −3
φ60 +1
0
9
+1.0
0
φ1.5 +0.1
0
Part No. Explanation
M N R 1 4
Part No.
E 0 A P
J
Nominal resistance
Resistance code,3 digits,
000 denotes Jumper type.
Resistance tolerance
J
F
±
5%
±
1%
J is also used
for jumper
Packaging Specifications Code
Part No.
MNR14
Code
E0AP
Resistance tolerance
J(
±
5%)
J(
±
5%)
Packaging specifications
Paper tape (4mm Pitch)
Reel
φ180mm
(7in.)
Basic ordering unit (pcs)
5,000
Reel (
φ
180) : JEITA ET-7200B
: Standard product
Rev.C
3/4
MNR14
Resistors
Electrical characteristics
TEMPERATURE COEFICIENT (
ppm /
°C)
6.0
5.0
4.0
3.0
2.0
1.0
0
−1.0
−2.0
−3.0
−4.0
−5.0
−6.0
10
100
1k
10k
100k
1M
JIS C 5201-1 4.5
SAMPLE SIZE : n=40pcs
20°C 65%RH
400
300
200
∆R/R
(%)
JIS C 5201-1 4.8
SAMPLE SIZE : n=20pcs
25°C /
−55°C
25°C / 125°C
6.0
4.0
2.0
0
−2.0
−4.0
−6.0
JIS C 5201-1 4.13
SAMPLE SIZE : n=20pcs
RATED VOLTAGE×2.5TIMES 2s
MAXIMUM OVERLOAD VOLTAGE : 100V
DC RESISTANCE
(%)
100
0
−100
−200
−300
−400
10
100
1k
10k
100k
1M
10
100
1k
10k
100k
1M
RESISTANCE
(Ω)
RESISTANCE
(Ω)
RESISTANCE
(Ω)
Fig.2 Resistance
Fig.3 Variation resistance with
temperature
Fig.4 Overload
3.0
2.0
1.0
JIS C 5201-1 4.18
SAMPLE SIZE : n=20pcs
SOLDERING CONDITION
: 260°C 10S
∆R/R
(%)
3.0
2.0
1.0
0
−1.0
−2.0
−3.0
JIS C 5201-1 4.19
SAMPLE SIZE : n=20pcs
−55°C
/ 125°C 5cyc
6.0
4.0
2.0
JIS C 5201-1 4.24
SAMPLE SIZE : n=20pcs
40°C 93%RH WITH NO LOAD
1,000h
∆R/R
(%)
0
−1.0
−2.0
−3.0
∆R/R
(%)
10
100
1k
10k
100k
1M
0
−2.0
−4.0
−6.0
10
100
1k
10k
100k
1M
RESISTANCE
(Ω)
10
100
1k
10k
100k
1M
RESISTANCE
(Ω)
RESISTANCE
(Ω)
Fig.5 Resistance to soldering heat
Fig.6 Rapid change of
temperature
Fig.7 Damp heat, steady state
6.0
4.0
2.0
6.0
2.0
JIS C 5201-1 4.25.3
SAMPLE SIZE : n=20pcs
125°C WITH NO LOAD 1,000h
JIS C 5201-1 4.25.1
SAMPLE SIZE : n=20pcs
70°C 1,000h
OVERLOAD : THE RATED
VOLTAGE
4.0
2.0
1.5
1.0
JIS C 5201-1 4.29
SAMPLE SIZE : n=20pcs
IPA, 5min.
∆R/R
(%)
∆R/R
(%)
0
−2.0
−4.0
−6.0
0
−2.0
−4.0
−6.0
∆R/R
(%)
10
100
1k
10k
100k
1M
0.5
0
−0.5
−1.0
−1.5
−2.0
10
100
1k
10k
100k
1M
10
100
1k
10k
100k
1M
RESISTANCE
(Ω)
RESISTANCE
(Ω)
RESISTANCE
(Ω)
Fig.8 Endurance
at 70°C
Fig.9 Endurance
Fig.10 Resistance to solvents
Rev.C
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
