SPECIFICATION CONTROL DRAWING
TITLE
44A122X
Date
TWO CONDUCTOR CABLE, SHIELDED, JACKETED,
GENERAL PURPOSE, 1000 VOLT
1-9-06
Revision
D
This specification sheet forms a part of the latest issue of Raychem Specification 44.
SHIELD - COPPER, COATING SAME AS ON
CONDUCTOR EXCEPT TIN-COATED
SHIELD WITH SILVER-COATED HIGH
STRENGTH ALLOY CONDUCTOR
COMPONENT WIRE - 44A021X
JACKET - RADIATION-CROSSLINKED,
MODIFIED PVF
2
TABLE I. CABLE CONSTRUCTION DETAILS
CONDUCTOR
SIZE
(AWG)
26
24
22
20
18
16
14
12
10
8
6
4
SHIELD
SIZE
(AWG)
36
36
36
36
36
36
36
36
36
36
34
34
JACKET
THICKNESS
(in.)
MINIMUM
.006
.006
.006
.006
.007
.007
.007
.008
.008
.010
.010
.013
NOMINAL
.008
.008
.008
.008
.009
.009
.009
.010
.010
.012
.012
.015
OUTSIDE
DIAMETER
(in.)
NOMINAL
.118
.130
.146
.162
.186
.202
.236
.276
.334
.458
.558
.672
MAXIMUM
.124
.136
.152
.169
.193
.210
.244
.286
.351
.481
.586
.705
MAXIMUM
WEIGHT
(lb/1000 ft)
10.3
12.9
16.2
20.7
27.9
33.4
45.9
64.3
96.3
161.
247.
377.
PART NUMBER
1/
44A122X-26-*
44A122X-24-*
44A122X-22-*
44A122X-20-*
44A122X-18-*
44A122X-16-*
44A122X-14-*
44A122X-12-*
44A122X-10-*
44A122X- 8-*
44A122X- 6-*
44A122X- 4-*
PART NUMBER
1/
44A122X-26-*
44A122X-24-*
44A122X-22-*
44A122X-20-*
44A122X-18-*
44A122X-16-*
44A122X-14-*
44A122X-12-*
44A122X-10-*
44A122X- 8-*
44A122X- 6-*
44A122X- 4-*
TABLE II. CABLE PERFORMANCE DETAILS
BEND TESTING
MANDREL DIAMETER
(inch) (± 3%)
LIFE CYCLE, IMMERSION
AND ACCELERATED AGING
3.00
6.00
6.00
6.00
6.00
6.00
6.00
10.0
10.0
18.0
18.0
18.0
COLD
BEND
3.00
6.00
6.00
6.00
6.00
6.00
6.00
10.0
10.0
18.0
18.0
18.0
WEIGHT
(lb) (± 3%)
COLD
BEND
3.00
6.00
6.00
9.00
9.00
12.0
12.0
12.0
12.0
15.0
24.0
24.0
LIFE CYCLE, IMMERSION
AND ACCELERATED AGING
.375
.375
.375
.500
.500
1.00
1.00
1.50
2.00
3.00
3.00
3.00
NOTE: Nominal values are for information only.
Nominal values are not requirements.
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.
R
Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
Page 1 of 2
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
© 2006 Tyco Electronics Corporation. All rights reserved.
Revision
SCD Number
SPECIFICATION CONTROL DRAWING
Page 2 of 2
D
44A122X
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
VOLTAGE RATING: 1000 volts (rms) at sea level
ACCELERATED AGING: 300 ± 3°C for 6 hours
BLOCKING: 150 ± 3°C for 6 hours
DIELECTRIC WITHSTAND: 3000 volts (rms), 60 Hz, 1 minute
FLAMMABILITY: 30 seconds (maximum); 3 in. (maximum); no flaming of facial tissue
IMMERSION: Diameter increase 5% (maximum); no cracking, no dielectric breakdown
JACKET COLOR: White preferred
JACKET CONCENTRICITY: 70% (minimum)
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 200% (minimum)
Tensile Strength, 4000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1.5 kV (rms)
Impulse Dielectric Test, 6.0 kV (peak)
LIFE CYCLE: 200 ± 3°C for 168 hours
LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours
SHIELD COVERAGE: 85% (minimum)
VOLTAGE WITHSTAND TEST (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute
PART NUMBER:
The “X” in the part numbers on page 1 shall be replaced by the applicable
conductor material designator as follows:
1 tin-coated copper
2 silver-coated copper
3 nickel-coated copper
4 silver-coated high strength copper alloy (AWG's 26-16 only)
6 nickel-coated high strength copper alloy (AWG's 26-20 only)
The "*" in the part numbers on page 1 shall be replaced by color code designators
with a dash separating the component wire color from the jacket color.
1/ Example: AWG 20, tin-coated copper, black and brown component wires;
white jacket: 44A1221-20-0/1-9
1/ see footer section on page 1
Microchip MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
