STANDARD
Resistive Touch Panel Specification
FID-550 7-Wire Series
Input Panel
Panel Drive
change over
switch
Noise Filter
MCU
Control
Section
A/D con-
verter
Interface
n
FEATURES
•
Superior long life, using a unique construction method offering improved life over typical
technologies; by sensing data input only on the glass layer, typically a 10x improvement in
product life is achived.
•
Excellent specification and high quality
- Anti-Newton ring technology
- High reliability materials
•
Pen/Finger, Pen Only, Finger Only,
Light Touch types available
•
Transparency 80% - typical
n
PART NUMBERS
Touch Panels:
Part Number
N010-0510-T302
N010-0510-T211
N010-0550-T913
N010-0551-T242
N010-0550-T811
Siz e
17 "
15 "
13.3 "
Typ e
Pen/Finge r
Pen/Finge r
Pen/Finge r
Pen/Finge r
Pen/Finge r
P en o nl y
Pen/Finge r
Pen/Finge r
Pen/Finge r
n
PART NUMBERS
Interface Controller Chips:
Part Number
N010-0559-V022
NC41120-0015
Type
7-Wire, RS232
7-Wire, USB
n
PART NUMBERS
Controller Boards:
Part Number
N16B-0558-B240
N16B-0558-B720
Type
7-Wire, RS232
7-Wire, USB
N010-0550-T711 12.1 "
1 1. 3
12.1 " Pen/Finger (light touch type )
N010-0550-T601 10.4 "
N010-0550-T611 10.4 "
N010-0550-T511
N010-0550-T341
9.5 "
8.4 "
N010-0550-T621 10.4 " Pen/Finger (light touch type )
FID-550 SERIES
n
DIMENSION EXAMPLE (10.4” SHOWN)
(3.50)
(11.50)
(12.50)
(13.50)
(24.30)
3.50
11.50
12.5±0.5
13.50
23.20
243.80
236.80
217.10 (transparent area)
215.10
213.10 (input area)
123.75
48.80±1.0
Top
46.20±2.0
3.50±1.0
15.20±1.0
16.20
17.20
24.30±1.0
23.20±1.0
70.20±1.0
118.20±1.0
164.20±1.0
47.00
93.70
187.40
180.40
164.40 (transparent area)
162.40
160.40 (input area)
47.0 x 3=141.00
(8.00)
1
Right
Left
7
16.00
22.00
90.5±1.0
(3.50)
(11.50)
(12.50)
(13.50)
(23.20)
Bottom
Unit: mm
n
DETAILED SPECIFICATION
n
1.0 APPLICATION
This specification applies to the 10.4” (inch) standard Touch Panel (Pen/Finger type). P/N is N010-0550-T611.
n
2.0 ADDITIONAL APPLICATIONS
Control IC specifications and Control PCB, complete Touch Panel Specifications are also applicable.
n
3.0 DISCRIPTION AND BLOCK DIAGRAM
This panel in combination with a control IC chip is used to transfer the co-ordinates of the touched position to
the host system (see block diagram above).
n
4.0 DRAWING
(Please see the diagram above.)
Definitions of the major dimensions indicated on this diagram:
Effective Input Area (A)
Area guaranteed to meet all the
characteristics detailed in this specification
View / Transparent Area (B)
The area inside the adhesive zone
or electrode pattern.
Anti-input Area (C)
An insulating area allowed to protect
the touch panel from giving false
readings when an enclosure touches
the panel.
n
5.0 CHARACTERISTICS
n
5.1 MECHANICAL
Operating Force
0.05~0.49 N (5 ~ 50gF) Measured with
a Silicon Measurement Rod R 8
(Round type 8mm) Silicon Rubber
Hardness 60˚C
Hardness of Surface
Pencil hardness 3H minimum against
specification JIS K-5400
n
5.2 OPTICAL
Transparency
Haze
Silicon Rubber Rod
78% min measured in the effective input area to JIS K 7105 using a
MURAKAMI SHIKISAI KENKYUSHO type IIR 100 meter. Typically 80%.
5% measured in the effective input area using a MURAKAMI
SHIKISAI KENKYUSHO type IIR 100 meter with an Anti Glare treated
surface.
A
B
C
Force
FID-550 SERIES
n
5.3 ELECTRICAL
Location Accuracy:
Linearity:
Current Consumption:
Switch Bounce (Chattering):
Insulation resistance:
Dielectric Strength:
±2.5mm Measured over 9 points (See note 1)
1.5%
20mA max at DC 5V when applying 5VDC between pins 3 & 5
10ms min when using the silicon rubber measurement rod.
10MΩ minimum at 25KV DC applied between pins 3 & 7 or
between 5 and 7
25KV DC for 1 minute
Note 1:
Measurement condition of linearity is corrected within the
control IC. In general the location accuracy is specified
as follows:
Actual co-ordinate point - theoretical co-ordinate point
= location accuracy.
In general a 9 point co-ordinate calibration system is used
to adjust the micro controller accuracy. (20 point can be
used in combination with an EEPROM design).
Note 2:
Pins 3, 5 and 7 are the glass and film connection points.
n
5.4 ENVIRONMENTAL
Operating Temperature (*):
Storage Temperature:
Operating Humidity:
Storage Humidity:
Chemical Resistance:
Co-ordinate Point
Theoretical
Error
Actual
Distance
-5˚C to 60˚C
-30˚C to 70˚C
20% to 90% RH with a Maximum wet bulb temperature of 38˚C
10% ~ 90% RH with a Maximum wet bulb temperature of 38˚C
Coating with the following chemicals and storing at room temperature for
hours gives no problems. 10% NaCl-water solution, ethyl-acetate, ethyl-
alcohol, toluene, methyl-ethyl-ketone.
n
5.5 PEN LIFE
Character Writing life:
1,000,000 words minimum
Touch Input life :
10,000,000 times minimum
Note 1:
Words are written in the notes area and the size of the word is
7.5mm x 6.75mm. A word is any Alphabet / Number / Mark.
The pen is as shown below and applies a force of 250g.
A failure is judged to happen when the current consumption or
insulation resistance or dielectric strength are not met as
shown in 5.3. The location accuracy with 9 point calibration
must be ±4.4 mm max.
Effective input area
Notes
10 mm
9 mm
R
0.
8
Ø6.0
Ø.0
3.5
110.0±1.0
3.0
Ø
9.0
1.0
1.5
Ø 4.6
.0
3
FID-550 SERIES
n
5.6 FINGER LIFE
A finger is simulated by a silicon rubber plunger
R8 (Round type 8mm size) hardness 60˚C at 200g
at frequency 5Hz.
A failure is judged to happen when the current
consumption or insulation resistance or dielectric
strength are not met as shown in 5.3. The location
accuracy with 9 point calibration must be ±4.4 mm max.
Typical operating force is 150g max.
n
5.7 INFORMATION ON THE PANEL
The panel part number is visible from the film side
The production information is visible from the glass side.
Production year 99 00 etc.
1 2 3 4 5 6 7 8 9 X Y Z or 1 2 3 4 5 6 7 8 9 X Y Z
2 3 4 5 6 7 8 9 X Y Z or
23456789XYZ
January Production
February Production
December Production
Z or 1 2 3 4 5 6 7 8 9 Y Z
n
6 PACKAGING
n
6.1 PACKING SPECIFICATION
Vibration:
10~55 Hz at 1 Octave per minute 10G 20 cycles with one side 0.75mm
Drop test:
60cm Drop 1 corner, 3 crease lines and 6 faces. 1 each 1 time
After the test no glass: flaw or crack is seen, and no dent or scratch on the film.
Also glass and film must not separate.
n
6.1 PACKING DETAILS
Each touch panel is placed into a plastic bag and is
held in place by a slit cut into the side of the card-
board. A second insertion piece is placed into the
carton to again add stability. The qty is written on
the side of the box. For example the T611 has 26
pieces per box.
Insert
Touch panel with bag
Slit in cardboard
4
FID-550 SERIES
n
7.0 REJECT CRITERIA
Description
Film Dent
Reject Criteri a
Area ≥ 0.1mm
2
Area ≥ 0.05mm
2
& area < 0.1mm
2
Area < 0.05mm
2
Area > 0.1mm
2
Area ≥ 0.05mm
2
& area < 0.1mm
2
Area < 0.05mm
2
Area > 0.1mm
Area ≥ 0.03mm & width <0.1mm and length < 10mm
Area < 0.05mm
: to be zero
: to be max. 5 points
: none specified
: to be zero
: to be max. 5 points
: none specified
: to be zero
: to be max. 1 point
: none specified
Foreign
material
between
glass and film
Dot type
Line type
Scratch
Dot blur or hard coat
missing
Newton Ring
Glass flaw
Area ≥ 0.1mm
: to be zero
Area ≥ 0.03mm & width <0.1mm with length < 80mm : to be max. 1 point
Area < 0.03mm & width <0.1mm with length < 30mm : none specified
Area ≥ 0.5mm
2
Area ≥ 0.03mm
2
& area < 0.5mm
2
Area < 0.05mm
2
: to be zero
: to be max. 5 points
: none specified
These must not be seen from Panel film side under a fluorescent lamp (3
wavelength type lamp). Not to be verified form glass side.
To be no flaw which is bigger than that shown in the following diagram. The
number of flaws is not specified.
3mm
5mm
mm
mm
n
8.0 GENERAL POINTS OF CAUTION
Touch panels are made of glass, so care must be taken in handling them. Do not stress, pile, bend, lift by
the cable or put any stress on the film, for example moving by film face vacuum. In order to clean wring dry a
cloth which has been emersed in a natural detergent. DO NOT use any organic solvent, acid or alkali solu-
tion. Watch the edge of the panel when cleaning, again for safety reasons.
5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
