Switching spark gap
SSG with lead wires
B88069X6331****
SSG03X-1J
Features
Extremely long life time
Stable performance over life
Insensitive performance against variations in
temperature
Very low switching losses
Very short breakdown time
High reliability by robust design
RoHS-compatible
Application
Ignition of HID lamps
Electrical specifications
Nominal breakdown voltage V
N
Initial values
1) 2)
Static breakdown voltage V
S
First ignition value V
S, FTE
after 24 hours in darkness
Following ignition values V
S, FIV
Electrical life time
3)
Breakdown voltage V
B
First ignition value V
B, FTE
after 24 hours in darkness
Ignition time t
I
at V
0
during life
Following ignition values V
B, FIV
Switching operations
at + 25 °C
Test circuit parameters
Open circuit voltage V
0
Loading resistance R
Discharge capacitance C
Inductance L
Discharge peak current I
P
General technical data
Insulation resistance at 100 V
Early ignition values below 290 V
Breakdown time
Maximum switching frequency
Maximum loading current
Weight
Marking, red positive
350
WW
Y
O
At delivery AQL 0,65 level II, DIN ISO 2859
Fig. 1 and 2
3)
Fig. 3 and 4
PPD AB PD / PPD AB PM
2)
1)
350
V
420
290 ... 390
V
V
450
300
290 ... 390
50 000
450
10
680
0.5
~ 500
> 100
2
50
200
50
~2
350 WWY O
V
ms
V
Ignitions
V
k
nF
µH
A
M
%
ns
Hz
mA
g
- Nominal voltage
- Calendar week of production
- Year of production
- Non radioactive
Issue 02 / 2009-10-20
Page 2 of 5
Please read
Cautions and warnings
and
Important notes
at the end of this document.
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain
statements about the suitability of our products for
certain areas of application.
These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out
that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a
rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that
in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified.
In customer applications requiring a very high
level of operational safety and especially in customer applications in which the malfunction or
failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of the
customer application or other action taken by the customer (e.g. installation of protective circuitry
or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or
failure of an electronic component.
3.
The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements,
some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous).
Useful information on this will be found in our Material
Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed
questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently,
the products described in this
publication may change from time to time.
The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also
reserve the right to discontinue production and delivery of products.
Consequently,
we cannot guarantee that all products named in this publication will always be available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts,
all orders are subject to the current version of
the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap, DSSP,
MiniBlue, MiniCell, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap,
SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K,
ThermoFuse, WindCap are
trademarks registered or pending
in Europe and in other countries.
Further information will be found on the Internet at www.epcos.com/trademarks.
Page 5 of 5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
