NUMBER
TYPE
GS-12-577
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
1 of 17
B
DATE
MezzoStak™ 0.5 BTB Connector System
AUTHORIZED BY
S. Stoner
CLASSIFICATION
27 May 10
UNRESTRICTED
1.0
OBJECTIVE
This specification defines the performance, test, quality, and reliability requirements of the MezzoStak™ 0.5 BTB
Connector System as well as Lead Free product that meets the requirement of the European Union Directives of
Restriction for Hazardous Substances (Directive 2002/95/EC).
2.0
SCOPE
This specification is applicable to the termination characteristics of the MezzoStak™ 0.5 BTB connector system,
which provides for parallel interconnection of printed wiring boards in low power applications.
Copyright FCI
Form E-3334
Rev F
GS-01-001
PDM: Rev:B
STATUS:
Released
Printed: Nov 29, 2010
.
NUMBER
TYPE
GS-12-577
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
2 of 17
B
DATE
MezzoStak™ 0.5 BTB Connector System
AUTHORIZED BY
S. Stoner
CLASSIFICATION
27 May 10
UNRESTRICTED
3.0
GENERAL
PARAGRAPH
1.0
2.0
3.0
4.0
5.0
5.1
5.2
5.3
5.4
6.0
7.0
8.0
9.0
9.1
9.2
9.3
9.4
9.5
TITLE
Objective
Scope
General
Applicable Documents
Requirements
Qualification
Material
Finish
Design and Construction
Electrical Characteristics
Mechanical Characteristics
Environmental Conditions
Quality Assurance Provisions
Equipment Calibration
Inspection Conditions
Sample Quantities and Description
Qualification Testing
Requalification Testing
4.0
APPLICABLE DOCUMENTS
In the event of a conflict between the requirements outlined in this specification and the product drawing, the
product drawing shall take precedence. In the event of a conflict between the requirements outlined in this
specification and the referenced documents, this specification shall take precedence.
4.1
SPECIFICATIONS
4.1.1
4.2
Engineering Drawings 10088779, 10088780, 10088781, 10090516, & 10090504
MILITARY STANDARDS
4.2.1
4.2.2
4.2.3
MIL-STD-202F: Test Methods for Electronic Component Parts
EIA-364: Test Methods for Electrical Connectors
MIL-C-45662: Equipment Calibration
4.3
OTHER STANDARDS AND SPECIFICATIONS
4.4.1
4.4.2
4.4.3
4.4.3
4.4.4
UL-94:
Flammability
ASTM B-19: Brass
ASTM B-36: Brass
ASTM E-8; ASTM B422-90: Copper Tin
ISO 9000
Copyright FCI
Form E-3334
Rev F
GS-01-001
PDM: Rev:B
STATUS:
Released
Printed: Nov 29, 2010
.
NUMBER
TYPE
GS-12-577
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
3 of 17
B
DATE
MezzoStak™ 0.5 BTB Connector System
AUTHORIZED BY
S. Stoner
CLASSIFICATION
27 May 10
UNRESTRICTED
4.5
FCI SPECIFICATIONS
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
BUS-03-114:
BUS-03-404:
GS-19-037:
GS-19-036:
GS-19-039:
Capacitance Measurement
Normal Force Measurement
Solderability
Porosity
Plating Adhesion
4.6
FCI LAB REPORTS - SUPPORTING DATA
4.6.1
EL-2010-04-015: Qualification Testing
5.0
REQUIREMENTS
5.1
QUALIFICATION
Connectors furnished under this specification shall be products that are capable of meeting the
qualification test requirements specified herein.
5.2
MATERIAL
The material for each part shall be as specified herein, or equivalent. Substitute material shall meet
the performance requirements of this specification.
5.2.1
5.2.2
5.2.3
Hermaphroditic Terminal. The base material shall be copper alloy strip.
Hold-Down. The base material shall be full brass strip.
Insulator Housing. The insulators shall be molded of 40% mineral filled liquid crystal
polymer that is rated 94V-0 or better in accordance with UL-94.
Pick-Up Cap The Pick-Up Cap shall be molded of 30% glass fiber filled liquid crystal
polymer that is rated 94V-0 or better in accordance with UL-94...
5.2.4
5.3
FINISH
5.3.1
The header and receptacle terminals shall be plated in the contact area with 0.38
micrometers min. GXT™ over 2.54 micrometers Nickel. The terminal solder tail shall be
plated with 0.10 min. micrometers Au over 1.27 micrometers min. Nickel. The terminal
areas outside of the contact area and solder tail areas shall be plated with 1.27 min.
micrometers Nickel.
The hold-down shall be plated with 2.5 min micrometers min. Sn over 1.3 micrometers
min. Nickel.
5.3.2
Copyright FCI
Form E-3334
Rev F
GS-01-001
PDM: Rev:B
STATUS:
Released
Printed: Nov 29, 2010
.
NUMBER
TYPE
GS-12-577
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
4 of 17
B
DATE
MezzoStak™ 0.5 BTB Connector System
AUTHORIZED BY
S. Stoner
CLASSIFICATION
27 May 10
UNRESTRICTED
5.4
DESIGN AND CONSTRUCTION
The connector shall be a multi-piece assembly having two rows of contacts with surface mount
solder tail terminations and solderable surface mount retention devices for installation on surface
mount printed wiring boards or flexible circuits.
5.4.1
Mating. The connector shall be capable of mating and unmating manually without the
use of special tools.
Visual Examination of Product – Under 10x magnification, connectors shall be uniform in
quality and shall be free from burrs, scratches, cracks, voids, chips, blisters, pin holes,
sharp edges, and other defects that will adversely affect life or serviceability. Open knit
lines, which may appear as a crack, may be present in the housing as long as they do not
adversely affect the performance of the connector as per the requirements outlined in this
specification.
5.4.2
6.0
ELECTRICAL CHARACTERISTICS
6.1
CURRENT RATING
The maximum current rating based upon a 30 degree C temperature rise over ambient is 0.5 amps
DC per contact for a 40 position connector with all contacts carrying current. The maximum current
carrying capacity for an individual contact is 0.5 amps DC measured in accordance with EIA-364-70.
See Figure 5.0 for thermocouple location
6.2
LOW LEVEL CONTACT RESISTANCE
The low level contact resistance of the 4mm, 4.5mm, 5mm, 5.5mm, 6.0mm, 6.5mm and 7.0mm
mated height connectors shall not exceed a delta of 10 milliohms max. after environmental exposure
when measured in accordance with EIA-364 TP23. The following details shall apply:
A.
B.
6.3
Test Voltage: 20 millivolts DC max. open circuit
Test Current: Not to exceed 100 milliamperes.
INSULATION RESISTANCE
The insulation resistance of the mated connectors shall not be less than 500 megaohms after
environmental exposure when measured in accordance with EIA-364-21. The following details shall
apply:
A.
B.
C.
Test voltage: 150 volts DC
Preparation: The connectors shall be mated but not soldered to a P.C. board.
Measurement points: The insulation resistance shall be measured between a minimum
of 5 adjacent contacts per connector as per Figure 1.0.
Copyright FCI
Form E-3334
Rev F
GS-01-001
PDM: Rev:B
STATUS:
Released
Printed: Nov 29, 2010
.
NUMBER
TYPE
GS-12-577
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
5 of 17
B
DATE
MezzoStak™ 0.5 BTB Connector System
AUTHORIZED BY
S. Stoner
CLASSIFICATION
27 May 10
UNRESTRICTED
6.4
DIELECTRIC WITHSTANDING VOLTAGE
There shall be no evidence of arc-over, insulation breakdown or leakage current in excess of 1
milliampere when the unmated connector is tested in accordance with EIA-364-20. The following
details shall apply:
A.
B.
C.
D.
Test voltage: 500 volts rms at 60 hz.
Test duration: 60 seconds
Preparation: The connectors shall be mated but not soldered to a P.C. board.
Measurement points: The dielectric withstanding voltage shall be applied across a
minimum of 5 pair of adjacent contacts. See Figure 1.0
6.5
CAPACITANCE
The capacitance between adjacent and opposing contacts in a mated connector shall not exceed
2.0 picofarads when tested in accordance with Du Pont specification BUS-03-114. The following
details shall apply:
A.
B.
C.
Test frequency: 100 khz
Preparation: The connectors shall be mated but not soldered to a P.C. board.
Measurement points: The capacitance shall be measured across a minimum of 5 pair of
adjacent contacts. See Figure 1.0
7.0
MECHANICAL CHARACTERISTICS
7.1
CONTACT RETENTION
Individual contacts in the un-terminated portions of the connector shall withstand a load normal to
the solder tail of 50gms min. The force shall be measured on a minimum of 5 contacts per row of an
unmated connector. The crosshead speed shall be no greater than 0.2 inches per minute.
7.2
MATING FORCE
The force to mate the connectors that are mounted on a P.C. board shall not exceed 68gms per
mated pair of contacts. The crosshead speed shall be no greater than 1.0 inches per minute.
7.3
UNMATING FORCE
The force to un-mate the connectors that are mounted on a P.C. board shall be no less than 30gms
per mated pair of contacts. The crosshead speed shall be no greater than 1.0 inch per minute.
Copyright FCI
Form E-3334
Rev F
GS-01-001
PDM: Rev:B
STATUS:
Released
Printed: Nov 29, 2010
.
聊聊、笑笑、闹闹
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
