MIC5212
Micrel
MIC5212
Dual 500mA LDO Regulator
Final
General Description
The MIC5212 is a dual linear voltage regulator with very-low
dropout voltage (typically 10mV at light loads and 350mV at
500mA), very-low ground current (225µA at 10mA output),
and better than 1% initial accuracy.
Both regulator outputs can supply up to 500mA at the same
time as long as each regulator’s maximum junction tempera-
ture is not exceeded.
Key features include current limiting, overtemperature shut-
down, and protection against reversed battery.
The MIC5212 is available in a fixed 3.3V/2.5V output voltage
configuration. Other voltages are available; contact Micrel for
details.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Fused lead frame SOIC-8
Up to 500mA per regulator output
Low quiescent current
Low dropout voltage
Tight load and line regulation
Low temperature coefficient
Current and thermal limiting
Reversed input polarity protection
Hard disk drives
CD R/W
Bar code scanners
SMPS post regulator/DC-to-DC modules
High-efficiency linear power supplies
Applications
Ordering Information
Part Number
MIC5212-SJBM
Voltage
3.3V/2.5V
Accuracy
1.0%
Junction Temp. Range*
–40°C to +125°C
Package
8-lead SOIC
Other voltages available. Contact Micrel for details.
Typical Application
MIC5212-SJBM
IN = 5V
4.7µF
INA OUTA
INB
OUTB
GND
V
O2
= 2.5V
4.7µF 4.7µF
V
O1
= 3.3V
3.3V/2.5V Dual LDO
Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 944-0970 • http://www.micrel.com
April 2003
1
MIC5212
MIC5212
Micrel
Absolute Maximum Ratings
(Note 1)
Supply Input Voltage (V
IN
A or B) ................. –20V to +20V
Power Dissipation (P
D
) ............................ Internally Limited
Storage Temperature Range ................... –60°C to +150°C
Lead Temperature (soldering, 5 sec.) ....................... 260°C
Operating Ratings
(Note 2)
Supply Input Voltage (V
IN
) ............................... 2.5V to 16V
Junction Temperature (T
J
) ....................... –40°C to +125°C
Thermal Resistance
(θ
JA
).........................................
Note 3
Electrical Characteristics
Regulator A and B
V
IN
= V
OUT
+ 1V; I
L
= 100µA; C
L
= 4.7µF; T
J
= 25°C,
bold
values indicate –40°C
≤
T
J
≤
+125°C; unless noted.
Symbol
V
O
∆V
O
/∆T
∆V
O
/V
O
∆V
O
/V
O
V
IN
– V
O
Parameter
Output Voltage Accuracy
Output Voltage
Temperature Coefficient
Line Regulation
Load Regulation
Dropout Voltage,
Note 6
(per regulator)
Conditions
variation from specified V
OUT
Note 4
V
IN
= V
OUT
+ 1V to 16V
I
L
= 0.1mA to 500mA,
Note 5
I
L
= 150mA
I
L
= 500mA
I
GND
Ground Pin Current,
Note 7
(per regulator)
I
L
= 150mA
I
L
= 500mA
PSRR
I
LIMIT
Ripple Rejection
Current Limit
Spectral Noise Density
Note 1.
Note 2.
Note 3.
Min
–1
–2
Typical
Max
1
2
Units
%
%
ppm/°C
40
0.009
0.05
175
350
1.5
12
75
750
500
1000
0.05
0.1
0.7
1.0
275
350
500
600
2.5
3.0
20
25
%/V
%/V
%
%
mV
mV
mV
mV
mA
mA
mA
mA
dB5
mA
nV/√Hz
f = 120Hz, I
L
= 150mA
V
OUT
= 0V
V
OUT
= 2.5V, I
OUT
= 50mA, C
OUT
= 2.2µF
Exceeding the absolute maximum rating may damage the device.
The device is not guaranteed to function outside its operating rating.
Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when
operating the device outside of its operating ratings. The maximum allowable power dissipation is a function of the maximum junction
temperature, T
J(max)
, the junction-to-ambient thermal resistance,
θ
JA
, and the ambient temperature, T
A
. The maximum allowable power
dissipation at any ambient temperature is calculated using: P
D(max)
= (T
J(max)
– T
A
)
÷ θ
JA
. Exceeding the maximum allowable power dissipa-
tion will result in excessive die temperature, and the regulator will go into thermal shutdown. The
θ
JA
of the 8-lead SOIC (M) is 63°C/W
mounted on a PC board (see
“Thermal Considerations”
section for further details).
Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range.
Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load
range from 0.1mA to 500mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification.
Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V
differential.
Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of
the load current plus the ground pin current.
Note 4.
Note 5.
Note 6.
Note 7.
April 2003
3
MIC5212
Microchip MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
