austriamicrosystems AG
is now
ams AG
The technical content of this austriamicrosystems datasheet is still valid.
Contact information:
Headquarters:
ams AG
Tobelbaderstrasse 30
8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
e-Mail:
ams_sales@ams.com
Please visit our website at
www.ams.com
Datasheet
AS1364
1 A L o w D r o p o u t L i n e a r Vo l t a g e R e g u l a t o r
1 General Description
The AS1364 is a low-dropout linear regulator (LDO) designed to
operate from 2V to 5.5V input, that delivers a wide range of highly
accurate (±0.75%) factory-trimmed output voltages as well as
adjustable output voltages (using an external resistor-divider
network).
The ultra-low dropout device requires only 140mV dropout voltage
while delivering a guaranteed 1A load current and is therefore
perfectly suited for battery-operated portable applications.
Additionally the AS1364 offers extremely low 10µV
RMS
(100Hz to
100kHz) or 45µV
RMS
(10Hz to 1MHz) output voltage noise.
Table 1. Standard Products
Model
2 Key Features
Guaranteed Output Current: 1A
Low Dropout: 140mV @ 1A
Output Voltage Accuracy: Up to
2.0V to 5.5V Input Voltage
Fixed V
OUT
: 1.2V to 5.0V
Adjustable V
OUT
: 1.2V to 5.3V
Low Ground Current: 35µA
Low Shutdown Current: 10nA
±0.75%
AS1364-AD
AS1364-_ _
The device features an internal PMOS pass transistor (for a low
supply current of only 35µA), reset output, a low-power shutdown
mode, and protection from short-circuit and thermal-overload
conditions.
When in shutdown, a 5k (typ) discharge path is connected
between the output pin and ground. The AS1364 is available in a
8-pin TDFN 3x3mm package.
Figure 1. AS1364 - Typical Application Diagram
Te
c
www.austriamicrosystems.com
hn
ic a
al m
co s
A
nt G
en
ts
til
Output Type
Adjustable
Fixed
BYP
No
Yes
SET
Yes
No
Thermal Overload Protection
Output Current Limit
Output discharge path during shutdown
8-pin TDFN 3x3mm Package
Low Output Noise: 45µV
RMS
(from 10Hz to 1MHz)
3 Applications
The device is ideal for laptops, PDAs, portable audio devices, mobile
phones, cordless phones, and any other battery-operated portable
device.
3
6
V
IN
IN
4
OUT
5
1
7
C
IN
4.7µF
On
Off
IN
2
AS1364
OUT
POK
EN
8
Reset Output
C
BYP
10nF
GND
SET/BYP
Revision 1.8
lv
C
OUT
4.7µF
V
OUT
al
1 - 19
id
AS1364
Datasheet - P i n A s s i g n m e n t s
4 Pin Assignments
Figure 2. Pin Assignments (Top View)
POK 1
EN 2
8 GND
7 SET/BYP
IN 3
IN 4
6 OUT
5 OUT
4.1 Pin Descriptions
Table 2. Pin Descriptions
Pin Number
1
3, 4
5, 6
Te
c
Exposed pad
www.austriamicrosystems.com
hn
ic a
al m
co s
A
nt G
en
ts
til
Pin Name
POK
Description
2
EN
IN
OUT
7
SET/BYP
GND
8
Ground
Connect to
Substrate
Revision 1.8
Note:
Open-Drain POK Output.
POK remains low while V
OUT
is below the POK threshold.
Connect a 100k pull-up resistor from this pin to OUT to obtain an output voltage
(see Figure 1).
Active-Low Shutdown Input.
A logic low disables the output and reduces the supply current to
0.1µA. In shutdown, the POK output is low and OUT high impedance.
V
DD
: Normal operation.
GND: Shutdown.
2.0V to 5.5V Supply Voltage.
Bypass with a 4.7µF input capacitor to GND
(see Dropout Voltage on
page 11).
These inputs are internally connected, but they also must be externally connected for proper
operation.
Regulator Output.
Bypass with a 4.7µF low-ESR output capacitor to GND. Connect the OUT pins
together externally.
Voltage-Setting Input.
Connect to GND to select the factory-preset output voltage. Connect this pin to
an external resistor-divider for adjustable-output operation
(see Figure 1)
– (AS1364-AD only)
Bypass Pin.
Connect a 10nF capacitor from this pin to OUT to improve PSRR and noise performance.
(AS1364-AD does not offer this feature)
Connect to PCB metal area for heatsink purposes. May be left open or connected to common ground.
lv
2 - 19
AS1364
al
id
AS1364
Datasheet - A b s o l u t e M a x i m u m R a t i n g s
5 Absolute Maximum Ratings
Stresses beyond those listed in
Table 3
may cause permanent damage to the device. These are stress ratings only, and functional operation of
the device at these or any other conditions beyond those indicated in
Electrical Characteristics on page 4
is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Table 3. Absolute Maximum Ratings
Parameter
Electrical Parameters
IN, EN, POK to GND
OUT, SET/BYP to GND
Output Short-Circuit Duration
Latch-Up
Electrostatic Discharge
ESD
Temperature Ranges and Storage Conditions
Thermal Resistance
JA
Operating Temperature Range
Storage Temperature Range
Junction Temperature
2
36.3
+85
kV
ºC/W
ºC
ºC
-100
-0.3
-0.3
+7
V
IN
+ 0.3
Infinite
+100
mA
JEDEC 78
V
V
Min
Max
Units
Comments
HBM MIL-Std. 883E 3015.7
methods
on PCB
Te
c
www.austriamicrosystems.com
hn
ic a
al m
co s
A
nt G
en
ts
til
-40
-65
+150
+125
ºC
Package Body Temperature
+260
ºC
Revision 1.8
The reflow peak soldering temperature (body temperature)
specified is in accordance with
IPC/JEDEC J-STD-020
“Moisture/Reflow Sensitivity Classification for Non-
Hermetic Solid State Surface Mount Devices”.
The lead finish for Pb-free leaded packages is matte tin
(100% Sn).
lv
3 - 19
al
id
AS1364
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6 Electrical Characteristics
Note:
All limits are guaranteed. The parameters with min and max values are guaranteed by production tests or SQC (Statistical Quality
Control) methods.
V
IN
= V
OUT(NOM)
+ 500mV or V
IN
= +2.0V (whichever is greater),C
IN
= C
OUT
= 4.7µF, EN = IN, T
AMB
= -40°C to +85ºC (unless otherwise
specified). Typical values are at T
AMB
= +25ºC.
Table 4. Electrical Characteristics
Symbol
V
IN
V
POR
Parameter
Input Voltage
Power On Reset
Output Voltage Accuracy
(Preset Mode)
V
OUT
Adjustable Output Voltage Range
SET/BYP Voltage Threshold
(Adjustable Mode)
Short-Circuit Current Limit
SET/BYP Threshold
Falling, 100mV hysteresis
I
OUT
= 250mA, T
AMB
= +25ºC
I
OUT
= 250mA
I
OUT
= 1mA to 1A, V
IN
> (V
OUT
+ 0.5V)
V
IN
= 2.5V, I
OUT
= 250mA,
V
OUT
set to 2.0V
V
OUT
= 0
1
Condition
Min
2.0
1.79
-0.75
-1.5
-2
Typ
1.87
Max
5.5
1.95
+0.75
+1.5
+2
V
SET/BYP
I
OUT
hn
ic a
al m
co s
A
nt G
en
ts
til
1.17
1
1.20
Guaranteed Output Current (RMS)
In-Regulation Current Limit
1.1
50
1.5
2.3
V
OUT
> 96% of nominal value, V
IN
2.0V
V
SET/BYP
= 1.20V
I
OUT
= 100µA
I
OUT
= 1A
1.5
100
35
SET/BYP Input Bias Current
Ground-Pin Current
2
1.2
I
LIMIT
I
SET
I
Q
-100
V
IN
- V
OUT
V
LNR
V
LDR
Dropout Voltage
I
OUT
= 250mA, V
OUT
= 3.3V
I
OUT
= 1A, V
OUT
= 3.3V
Line Regulation
V
IN
from (V
OUT
+ 100mV) to 5.5V,
I
LOAD
= 5mA
I
OUT
= 1mA to 1A
-0.125
Load Regulation
f = 1kHz, I
OUT
= 10mA, C
BYP
= 10nF
f = 1kHz, I
OUT
= 10mA
PSRR
Ripple Rejection
f = 10kHz, I
OUT
= 10mA, C
BYP
= 10nF
f = 10kHz, I
OUT
= 10mA
f = 100kHz, I
OUT
= 10mA, C
BYP
= 10nF
f = 100kHz, I
OUT
= 10mA
100Hz to 100kHz, C
OUT
= 3.3µF,
C
BYP
= 10nF;
10Hz to 1MHz, C
OUT
= 3.3µF,
C
BYP
= 10nF;
10Hz to 1MHz, C
OUT
= 3.3µF;
Te
c
Output Voltage Noise
100Hz to 100kHz, C
OUT
= 3.3µF;
www.austriamicrosystems.com
Revision 1.8
lv
%
5.3
V
1.23
V
A
A
A
mV
nA
µA
mV
%/V
%/mA
150
150
85
+100
200
75
35
140
320
+0.125
0.001
78
72
75
65
dB
54
46
10
50
45
70
µV
RMS
4 - 19
al
V
id
Unit
V
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
