SMT Power Inductors
Shielded Drum Core - PF0560 NL Series
Mechanicals
PF0560.XXXNL
Schematic
Weight
.................1.4 grams
Tape & Reel
...........620 reel
Tray
.........................60/tray
Dimensions:
Inches
mm
Inductance vs Current Characteristics
Unless otherwise specified,
all tolerances are
±
.004
0,10
Notes:
1. Unless otherwise specified, all testing is made at 100kHz, 0.1VAC.
2. Optional Tape & Reel packaging can be ordered by adding a “T” suffix to the part
number (i.e P1166.102NL becomes P1166.102NLT). Pulse complies with industry
standard Tape and Tape & Reel specification EIA481.
3. The “NL” suffix indicates an RoHS-compliant part numer. Non-NL suffixed parts are
not necessarily RoHS compliant, but are electrically and mechanically equivalent to
NL versions. If a part number does not have the “NL” version, but an RoHS compliant
version is required, please contact Pulse for availability.
4. Temperature of the component (ambient plus temperature rise) must be within
specified operating temperature range.
5. The rated current (Irated) as listed is either the saturation current or the heating
current depending on which value is lower.
6. The saturation current, Isat, is the current at which the component inductance drops
by the indicated percentage (typical) at an ambient temperature of 25C. This current
is determined by placing the component in the specified ambient environment and
applying a short duration pulse current (to eliminate self-heating effects) to the
component.
7. The heating current, Idc, is the DC current required to raise the component tempera-
ture by the indicated delta (approximately). The heating current isdetermined by
mounting the component on a typical PCB and applying current for 30 minutes. The
temperature is measured by placing the thermocouple on top of the unit under test.
8.
In high volt*time (Et) or ripple current applications, additional heating in the
component can occur due to core losses in the inductor which may necessitate
derating the current in order to limit the temperature rise of the component. In order
to determine the approximate total loss (or temperature rise) for a given application,
both copper losses and core losses should be taken into account.
Estimated Temperature Rise:
Trise = [Total loss (mW) / K0]
.833
(°C)
Total Loss = Copper loss + Core loss (mW)
Copper loss = I
RMS2
x DCR (Typical) (mW)
Irms = [I
DC2
+
ΔI
2
/12]
1/2
(A)
Core loss = K1 x f (kHz)1
.23
x Bac (Ga)
2.38
(mW)
Bac (peak to peak flux density) = K2 x
ΔI
(Ga)
[= K2/L (µH) x Et (V-µSec) (Ga)]
where f varies between 25kHz and 1MHz, and Bac is less than 2500 Gauss.
K2 is a core size and winding dependent value and is given for each p/n in the
proceeding datasheets. K0 & K1 are platform and material dependant constants and
are given in the table below for each platform.
2
power.pulseelectronics.com
SPM2007_24(08/17)
http://www.power.pulseelectronics.com/contact
SMT Power Inductors
Shielded Drum Core - PF0560 NL Series
Part No.
PG0085/86
PG0087
PG0040/41
P1174
PF0601
PF0464
PF0465
P1166
P1167
PF0560NL
P1168/69
P1170/71
P1172/73
PF0552NL
PF0553NL
Trise Factor
(KO)
2.3
5.8
0.8
0.8
4.6
3.6
3.6
1.9
2.1
5.5
4.8
4.3
5.6
8.3
7.1
Core Loss Factor
(K1)
5.29E-10
15.2E-10
2.80E-10
6.47E-10
14.0E-10
24.7E-10
33.4E-10
29.6E-10
42.2E-10
136E-10
184E-10
201E-10
411E-10
201E-10
411E-10
Take note that the component’s temperature rise varies depending on the system condition. It is suggested that the component be tested at the system level, to verify
the temperature rise of the component during system operation.
For More Information
Pulse Worldwide
Pulse Europe
Headquarters
Pulse Electronics GmbH
15255 Innovation Drive Ste 100 Am Rottland 12
San Diego, CA 92128
58540 Meinerzhagen
U.S.A.
Germany
Pulse China Headquarters
Pulse Electronics (ShenZhen) CO., LTD
D708, Shenzhen Academy of
Aerospace Technology,
The 10th Keji South Road,
Nanshan District, Shenzhen, P.R.
China 518057
Tel: 86 755 33966678
Fax: 86 755 33966700
Pulse North China
Room 2704/2705
Super Ocean Finance Ctr.
2067 Yan An Road West
Shanghai 200336
China
Tel: 86 21 62787060
Fax: 86 2162786973
Pulse South Asia
135 Joo Seng Road
#03-02
PM Industrial Bldg.
Singapore 368363
Pulse North Asia
1F., No.111 Xiyuan Rd
Zhongli City
Taoyuan City 32057
Taiwan (R.O.C)
Tel: 858 674 8100
Fax: 858 674 8262
Tel: 49 2354 777 100
Fax: 49 2354 777 168
Tel: 65 6287 8998
Fax: 65 6280 0080
Tel: 886 3 4356768
Fax: 886 3 4356820
Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may
be trademarks or registered trademarks of their respective owners. © Copyright, 2017. Pulse Electronics, Inc. All rights reserved.
3
power.pulseelectronics.com
SPM2007_24 (08/17)
http://www.power.pulseelectronics.com/contact
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
