7850 E. Gelding Drive
Scottsdale, AZ 85260
USA
1-877-2BUYNKK (228-9655)
Phone
480.991.0942
Fax
480.998.1435
www.nkksmartswitch.com
06–07
Demonstration Kit
User Guide
CONTENTS
NOTES
Introduction . . . . . . . . . . . . . . . . . . 2
Shipping Contents . . . . . . . . . . . . . . 3
Hardware Installation . . . . . . . . . . . . 4
Software Installation . . . . . . . . . . . . . 5
Programming Bitmaps . . . . . . . . . . . 7
Demonstration Kit Specifications . . . . . 8
Battery Box Specifications . . . . . . . . 13
Precautions for Handling & Storage . .14
INTRODUCTION
This User Guide will assist you in using the IS Demonstration Kit (DEM KIT),
consisting of an IS switch or IS display module mounted on PC board. A sub-
miniature controller manages 64 bitmaps and backlight data.
Bitmap data is controlled by 6-bit parallel TTL level signal and is edited by
the “IS Easy Editor,” downloaded to the kit via USB Type A-mini B cable (re-
quired for connection to a PC).
“IS Easy Editor” is the software to create and edit graphics. A variety of tool
functions allows you to customize bitmap images as well as change the setting of
the backlight.
Transfer of graphic data is simple with IS Easy Display Controller. An as-
sortment of samples is available, allowing customization of graphic images with
ease for your applications.
2
15
PRECAUTIONS FOR HANDLING & STORAGE
Handling
1. The IS Series devices are electrostatic sensitive.
2. Avoid excessive force to protect the LCD.
3. Do not exceed 60°C at the LCD level.
4. If the LCD is accidentally broken, avoid contact with the liquid and wash
off any liquid spills to the skin or clothing.
5. Do not connect to PC via USB when IS Easy Disply Kit is mounted on
battery box.
6. Deviation of drive current and temperature may change LCD contrast.
Control contrast via contrast adjustment on backside of IS Controller.
7. The IS series devices are not process sealed.
8. Clean cap surface with dry cloth. If further cleaning is needed, wipe
with dampened cloth using neutral cleanser and dry with clean cloth.
Do not use organic solvent.
Storage
1. Store away from direct sunlight.
2. Keep away from static electricity.
3. Avoid extreme temperatures, high humidity, gaseous substances, and all
forms of chemical contamination.
SHIPPING CONTENTS
1. Demonstration Kit User Guide
2. CD for “IS Easy Editor” Software and Manual
3. SMARTDISPLAY
TM
Mounted on Controller Board
or
4. SMARTSWITCH
TM
Mounted on Controller Board
5. Connector Block
6. USB Type A-Mini B Cable
7. (Optional) Battery Box (Batteries not included)
ELECTROSTATIC
SENSITIVE DEVICES
ATTENTION
7
1
6
2
5
4
or
3
14
3
HARDWARE INSTALLATION
The Connector Block (A) is required to illuminate the backlight of the DEM
KIT while programming through the USB Type A-mini B cable.
Connect as
shown,
prior to
connecting to the
USB cable.
Note the orienta-
tion of the Connector
Block to that of the
DEM KIT.
The Connector
Block is used ONLY
during the program-
ming phase; it is not
used with the Battery
Box option.
(OPTIONAL) BATTERY BOX SPECIFICATIONS
The Battery Box provides portability to
demonstrate functionality without any
system connections.
• Power Switch activates power
• FWD/REV Switch directs sequences
of bitmaps for IS15 SMARTSWITCH
TM
• Knob for cycling bitmaps may also
simulate animation
• Socket to mount IS Easy Display Controller
• Battery holder accommodates four (4) AA
alkaline batteries (not included)
Pin 1
Note: Orientation of DEM
KIT–1 or DEM KIT–2
to Battery Box
(100.0)
3.937
Connector Block (A)
(70.0)
2.756
(35.0)
1.378
Power Switch
Knob to cycle
through bimaps for
both IS15 and IS01
Switch to direct the
sequence of bitmaps for
IS15 SMARTSWITCH
TM
Connector for IS
Easy Display Kit
4
13
TYPICAL DEM KIT DIMENSIONS
Dem Kit –1 Side View
Dem Kit –2 Side View
IMPORTANT!
READ BEFORE SOFTWARE INSTALLATION
1. Read installation manual on CD (See Figure A).
2.
Do not connect hardware (IS Easy Display Controller) until installation
of drivers.
3. Turn off all resident software (i.e., antivirus software) before beginning
installation.
4. Make sure you have administrative rights to install software on your computer.
5. Minimum system requirements:
• CPU
Pentium or compatible processor
Windows XP Professional, Windows XP Home Edition
Windows 2000 Professional (Service Pack 2 or later)
Windows 98 Second Edition
• RAM
• Disk Space
• Browser
128MB
60MB of available space
Internet Explorer 6.0 or later
(2.54)
.100
(2.54)
.100
• OS
(26.9)
1.059
(1.6)
.063
(10.1)
.398
(17.4)
.685
(1.6)
.063
(10.1)
.398
CN1
USB Mini-B
Connector
(3.0)
.118
(2.8) DiaTyp
.110
SOFTWARE INSTALLATION
(20.5)
.807
(16.5)
.650
(21.0)
.827
Application
(44.5)
1.752
16 15
(20.0)
.787
2
(7.0)
.276
1. Click on “Installation of ‘IS Easy
Editor’ Application” (see Figure
A). “End User License Agreement”
window appears. Click “Agree”
to continue.
2. Follow the onscreen instructions to
load your software and configure
the settings.
3. “Install Complete” window appears.
Click “Finish”.
5
1
Top View
(16.0)
.630
(24.5)
.965
Contrast Adjustment
Figure A
Bottom View
CN2
2.54mm 16-pin
Header Connector
12
电子竞赛
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
