REVISIONS
LTR
A
B
C
DESCRIPTION
Add device type 02. Make changes to table I, figure 1, and editorial changes
throughout.
Changes in accordance with NOR 5962-R079-94.
Drawing updated to reflect current requirements. - lgt
DATE (YR-MO-DA)
90-06-29
94-03-24
01-08-23
APPROVED
William J. Johnson
Michael A. Frye
Raymond Monnin
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
PREPARED BY
Rick C. Officer
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
C
10
C
11
C
12
C
13
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
Charles E. Besore
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
APPROVED BY
William J. Johnson
MICROCIRCUIT, LINEAR, CMOS 16-BIT ANALOG -
TO- DIGITAL CONVERTER, MONOLITHIC
SILICON
DRAWING APPROVAL DATE
15 August 1989
AMSC N/A
REVISION LEVEL
C
SIZE
A
SHEET
CAGE CODE
67268
1 OF
13
5962-89676
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
5962-E566-01
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-89676
01
Q
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
Generic number
CS5016-S
CS5016-T
Circuit function
16-bit CMOS analog-to-digital converter, 16.25
s
16-bit CMOS analog-to-digital converter, 16.25
s
INL test
5.0 LSB
1.0 LSB
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
Q
X
Descriptive designator
GDIP1-T40 or CDIP2-T40
CQCC1-N44
Terminals
40
44
Package style
Dual-in-line
Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings. 1/
Positive digital supply (+V
D
) voltage range........................................... -0.3 V dc to +6.0 V dc 2/
Negative digital supply (-V
D
) voltage range .......................................... +0.3 V dc to -6.0 V dc
Positive analog supply (+V
A
) voltage range ......................................... -0.3 V dc to +6.0 V dc
Negative analog supply (-V
A
) voltage range......................................... +0.3 V dc to -6.0 V dc
Analog ground (AGND) to digital ground (DGND)................................
0.5 V dc
Input current, any pin except supplies..................................................
10 mA
3/
Analog input voltage (AIN and V
REF
pins)............................................. -V
A
–0.3 V dc to +V
A
+0.3 V dc
Digital input voltage .............................................................................. –0.3 V dc to +V
D
+0.3 V dc
Storage temperature range .................................................................. -65
C to +150
C
Lead temperature (soldering, 10 seconds)........................................... +260
C
Junction temperature (T
J
)..................................................................... +195
C
Power dissipation
Case Q .......................................................................................... 1500 mW
Case X .......................................................................................... 1100 mW
Thermal resistance, junction to case (
JC
) ........................................... See MIL-STD-1835
Thermal resistance, junction to ambient (
JA
)
Case Q .......................................................................................... 45
C/W
Case X .......................................................................................... 60
C/W
1/
2/
3/
All voltages referenced to AGND and DGND tied together.
In addition +V
D
must not be greater than +V
A
+ 0.3 V dc.
Transient currents of up to 100 mA will not cause latch-up.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89676
SHEET
C
2
1.4 Recommended operating conditions. 1/
Ambient operating temperature range (T
A
) .......................................... -55
C to +125
C
Positive digital supply voltage (+V
D
)..................................................... +4.5 V dc to +V
A
2/
Negative digital supply voltage (-V
D
) .................................................... -4.5 V dc to –5.5 V dc
Positive analog supply voltage (+V
A
) ................................................... +4.5 V dc to +5.5 V dc
Negative analog supply voltage (-V
A
)................................................... -4.5 V dc to –5.5 V dc
Digital ground (DGND) ......................................................................... 0 V dc
Analog ground (AGND) ........................................................................ 0 V dc
Digital input low voltage (V
IL
)................................................................ -0.3 V dc to +0.8 V dc
Digital input high voltage (V
IH
) .............................................................. +2.0 V dc to +V
D
Analog reference input voltage (V
REF
) range........................................ +4.5 V dc
Analog input voltage range:
Unipolar mode .................................................................................. AGND to +V
REF
Bipolar mode..................................................................................... -V
REF
to +V
REF
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed
in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in
the solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 -- Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 -
MIL-STD-1835 -
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -- List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
1/
2/
All voltages referenced to AGND and DGND tied together.
In addition +V
D
must not be greater than +V
A
+ 0.3 V dc.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89676
SHEET
C
3
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.2 Truth table. The truth table shall be as specified on figure 2.
3.2.3 Block diagram. The block diagram shall be as specified on figure 3.
3.2.4 Case outline. The case outline shall be in accordance with 1.2.2 herein.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For
packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the
option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
appendix A.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89676
SHEET
C
4
TABLE I. Electrical performance characteristics.
Conditions
-55
C
T
A
+125
C
unless otherwise specified
1/
Test
Symbol
Group A
subgroups
1, 2, 3
Device
type
All
Limits
Min
16
Max
Unit
Resolution for which
no missing codes is
guaranteed
Integral linearity error
Full-scale error
Full-scale error drift
Unipolar offset error
Unipolar offset error
drift
Bipolar offset error
Bipolar offset error
drift
Bipolar negative full-
scale error
Bipolar negative full-
scale error drift
Peak harmonic or
spurious noise
RES
Bits
INL
FSE
dFSE/d
t
VOFF
dVOFF/d
t
BOFF
dBOFF/d
t
BNFSE
1/ 2/
1/ 2/
1/ 2/ 3/ 4/
1/ 2/
1/ 2/ 3/ 4/
1/ 2/
1/ 2/ 3/ 4/
1/ 2/
1, 2, 3
1, 2, 3
2, 3
1, 2, 3
2, 3
1, 2, 3
2, 3
1, 2, 3
01
02
01
02
All
01
02
All
01
02
All
01
02
5.0
1.0
4.0
3.0
4.0
4.0
3.0
2.0
4.0
2.0
3.0
5.0
3.0
3.0
92
100
82
85
84
90
375
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
dBNFSE/d
t
S/PN
1/ 2/ 3/ 4/
1 kHz input, full scale
amplitude, bipolar mode
1/ 2/
12 kHz input, full scale
amplitude, bipolar mode
1/ 2/
2, 3
4, 5, 6
All
01
02
01
02
LSB
dB
Signal to noise ratio
S/(N+D)
1 kHz input, full scale
amplitude, bipolar mode
1/ 2/
Unipolar mode, T
A
= +25
C
1/ 3/
Bipolar mode, T
A
= +25
C
1/ 3/
4, 5, 6
01
02
dB
Analog input
capacitance in fine
charge mode
C
IN
4
All
pF
220
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-89676
SHEET
C
5
FPGA/CPLD
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
