NUMBER
TYPE
GS-12-1326
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
1 of 9
MINITEK RECEPTACLE
AUTHORIZED BY
CLASSIFICATION
DATE
4
20/05/15
UNRESTRICTED
1.0
Objective
This specification defines the performance, test, quality and reliability requirements of the Minitek Receptacle
product.
2.0
Scope
This specification is applicable to the termination characteristics of the Minitek Receptacle family of products
when mated with FCI Minitek
TM
headers or other 0.51mm pin compatibles headers, 2mm centerline.
This product provides board to board in vertical/horizontal, single row/double row, SMT/TMT configurations.
3.0
Ratings
3.1
3.2
3.3
Operating Voltage Rating = 200 Volts
Operating Current Rating = 2A
Operating Temperature Range = -55°C to 125°C
(1)
Note 1: includes the terminal temperature rise when powered
4.0
Applicable Documents
4.1
FCI Specifications
4.1.1
4.1.2
4.1.3
4.1.4
Engineering drawings
Process drawings
Application specification(s)
Material specification(s)
List all referenced ELX division documents including the test and procedure specifications referenced in the selected 6.0, 7.0,
and 8.0 paragraphs
4.2
Industry or Trade Association standards
List any applicable specifications, such as Telcordia Technologies, USB, etc.
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
For information only. This is a preliminary customer document that is subject to change without notice.
NUMBER
TYPE
GS-12-1326
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
2 of 9
MINITEK RECEPTACLE
AUTHORIZED BY
CLASSIFICATION
DATE
4
20/05/15
UNRESTRICTED
4.3
National or International Standards
List applicable specifications that are referenced in the specification e.g.:
4.3.1 Flammability: UL94V-0 or similar applicable specification
4.3.2 EIA 364: Electrical Connector/Socket Test Procedures Including Environmental Classifications.
4.3.3 IEC 60512: Connectors for Electronic Equipment – Tests and Measurement
4.4
FCI Laboratory Reports - Supporting Data
List lab report numbers that contain the supporting qualification test data
4.5
Safety Agency Approvals
List the UL, CSA, TUV other product safety agency certification file numbers.
5.0
Requirements
5.1
Qualification
Connectors furnished under this specification shall be capable of meeting the qualification test
requirements specified herein.
5.2
Material
The material for each component shall be as specified herein or equivalent.
5.2.1 Housing : High temperature Glass-filled polymer with a flame retardant rating of UL-94-V0
5.2.2 Terminal : Copper Alloy
Refer to GS-01-029 section 5.5 for additional material content recommendations
5.3
Finish
The finish for applicable components shall be as specified herein or equivalent.
5.3.1 Solder tails: 2μm min. pure matte Tin over 1.27μm nickel MIN under plating.
5.3.2 Contact areas : defined on the product drawings
• 0.76μm Gold over 1.27μm nickel MIN under plating
• 0.38μm Gold over 1.27μm nickel MIN under plating
• 0.20μm Gold over 1.27μm nickel MIN under plating
• 2μm min full Tin over 1.27μm nickel MIN under plating
5.3.3 All other areas will be plated with 1.27μm min of nickel.
Refer to GS-01-029 section 5.5 for additional finish content recommendations
5.4
Design and Construction
Connectors shall be of the design, construction, and physical dimensions specified on the applicable
product drawing. There shall be no cracks, burrs, or other physical defects that may impair
performance.
Include any additional product information that would provide the reader with a better understanding of the design, construction,
and intended use or application of the product. Refer to GS-01-029 section 5.5 for additional information regarding design and
construction content
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
For information only. This is a preliminary customer document that is subject to change without notice.
NUMBER
TYPE
GS-12-1326
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
3 of 9
MINITEK RECEPTACLE
AUTHORIZED BY
CLASSIFICATION
DATE
4
20/05/15
UNRESTRICTED
6.0
Electrical Characteristics
6.1
Contact Resistance, Low Level (LLCR)
The low level contact resistance shall not exceed 15 milliohms initially. The low level contact
resistance shall also not exceed 20 milliohms in resistance after any treatment and/or environmental
exposure. Measurements shall be in accordance with EIA 364-23.
The following details shall apply:
a. Method of Connection - Attach current and voltage leads as shown in Figure 1.
b. Test Voltage - 20 milli-volts DC max open circuit.
c. Test Current - Not to exceed 100 milli-amperes.
Figure 1
6.2
Insulation Resistance
The insulation resistance of unmated connectors shall not be less than 1000 Mohms initially and after
environmental exposure.
Measurements shall be in accordance with EIA 364-21.
The following details shall apply:
a. Test Voltage - 500 volts DC.
b. Electrification Time - 2 minutes, unless otherwise specified.
c. Points of Measurement - Between adjacent contacts
(and between contacts and other conductive
surfaces, if applicable).
6.3
Dielectric Withstanding Voltage
There shall be no evidence of arc-over, insulation breakdown, or excessive leakage current >1mA
when unmated connectors are tested in accordance with EIA 364-20.
The following details shall apply:
a. Test Voltage - 650 volts (AC RMS, 60Hz).
b. Test Duration - 60 seconds.
c. Test Condition - 1 (760 Torr - sea level).
d. Points of Measurement - Between adjacent contacts
(and between contacts and other conductive
surfaces, if applicable).
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
For information only. This is a preliminary customer document that is subject to change without notice.
NUMBER
TYPE
GS-12-1326
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
4 of 9
MINITEK RECEPTACLE
AUTHORIZED BY
CLASSIFICATION
DATE
4
20/05/15
UNRESTRICTED
6.4
Current Rating
The temperature rise above ambient shall not exceed 30 deg C at any point in the system when all
contacts are powered at 1A or one contact is powered at 2A.
The following details shall apply:
a. Ambient Conditions – Still air at 25°C.
b. Test configuration
(specify wire gage, test board requirements, thermocouple placement, sample
orientation, etc.)
c. Reference - EIA 364-70
7.0
Mechanical Characteristics
7.1
Mating/Unmating Force
The force to mate a receptacle connector and compatible header shall not exceed 1.8N per contact.
The unmating force shall not be less than 0.2N per contact.
If total force per connector is to be reported, change wording accordingly and/or place in table form below for various connector
sizes
The following details shall apply:
a. Cross Head Speed - 25 mm per minute.
b. Utilize free floating fixtures.
c. Reference – EIA 364-13.
TABLE OF TOTAL MATING/UNMATING FORCE, IF APPLICABLE
7.2
Durability
The connector pairs shall be capable of withstanding 100 mating/unmating cycles. (Add table of total
durability cycles for various applications, if applicable).
When used for pre-conditioning treatment, 50 mating/unmating cycles shall be applied prior to
mechanical/environmental exposure and 50 mating/unmating cycles shall be applied after
mechanical/environmental exposure. Reference EIA-364-09.
Plating options
0.76µm Gold
0.38µm Gold
0.20µm Gold
Durability Cycles
100
50
30
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
For information only. This is a preliminary customer document that is subject to change without notice.
NUMBER
TYPE
GS-12-1326
TITLE
PRODUCT SPECIFICATION
PAGE
REVISION
5 of 9
MINITEK RECEPTACLE
AUTHORIZED BY
CLASSIFICATION
DATE
4
20/05/15
UNRESTRICTED
8.0
Environmental Conditions
After exposure to the following environmental conditions in accordance with the specified test procedure
and/or details, the product shall show no physical damage and shall meet the electrical and mechanical
requirements per paragraphs 6.0 and 7.0 as specified in the Table 1 test sequences. Unless specified
otherwise, assemblies shall be mated during exposure.
Use recommended details or select others as appropriate
8.1
Thermal Shock –EIA 364-32.
a. Number of Cycles – 5
b. Temperature Range - Between -55°C and +125°C
c. Time at Each Temperature - 30 minutes
d. Transfer Time - 5 minutes, maximum
8.2
Humidity –EIA 364-31 method II (steady state)
a. Relative Humidity - 90% (for cyclic humidity, specify for temperature ramps, if applicable, and
temperature dwells)
b. Temperature – 40°C
c. Duration – 96h (hours, days, # of cycles, etc.)
d. Omit step 7a (cold shock) & 7b (vibration) where applicable
8.3
High Temperature Life – EIA 364-17.
a. Test Temperature – 125 C°
b. Test Duration – 250h
Refer to GS-01-029 section 5.8 for assistance in selecting appropriate temperature and duration
8.4
Mixed Flowing Gas corrosion (MFG) – EIA 364-65
a. Class - IIA
b. Duration - 20 days
c. Receptacles only exposed unmated, remated with headers no exposed
Unmated for 2/3 the duration (13 days) and mated the remaining 1/3 duration (7days)
Select class and duration as appropriate for the expected operating environment. Refer to the industry application/standard,
customer specification, or GS-03-004.
8.5
Salt Spray – EIA-364-26
a. Test Condition - B (refer to specified test method for condition)
b. Duration – 48h / 5% by weight (hours if not specified by selected condition above)
c. Acceptance criteria – (visual examination requirements and/or LLCR criteria)
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
For information only. This is a preliminary customer document that is subject to change without notice.
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
