IDEC's original Spring-up Terminals and Cover
Provide IP20 Fingersafe Protection.
17.5 mm
35.0 mm
52.5 mm
78.8 mm
(1-pole)
(2-pole)
Auxiliary/alarm contact terminals are
supplied with fingersafe covers.
(3-pole)
Fingersafe, spring-up terminals reduce
wiring time.
Ring terminals can be installed as screws are captive.
Retractable Lever
The lever retracts when the circuit breaker is set. As a
result, accidental operation due to bumping the lever, is
prevented. Status of the circuit breaker can easily be
determined by observing the position of the lever.
Retractable
Lever
ON
OFF
Slim Design Saves Space
Main Circuit Terminals are Fingersafe
(IP20)
1-pole
2-pole
3-pole
17.5mm Wide
35.0mm Wide
52.5mm Wide
Spring-up, fingersafe terminals do not require a cover.
Auxiliary/Alarm Contact Terminals are
Equipped with Fingersafe Covers
2
Auxiliary/Alarm Contact, and Relay Trip Voltage Coil
Terminals are Equipped with Fingersafe Covers.
35mm-wide DIN Rail Mounting
or Direct Panel Mounting
Conforms to various international
standards
After tripping, the retractable lever is in
the middle position.
Circuit breaker must be turned off before it can be reset.
Distinguishing Characteristics
Wide variety of rated currents and tripping curves.
One and two pole models are AC/DC compatible
and allow for a reduction in inventory.
Rated Short-circuit Capacity 2500A
Available with Inertia Delay
Safe Trip-free Mechanism
Allows for use with large inrush currents such as
motors and lamps.
The circuit remains open even when the operator is turned
on after tripping (unit must be manually reset after
removing the cause of the tripping).
ON
OFF
Tripped
Available with Auxiliary or Alarm Contacts
Auxiliary or Alarm Contact
(Shown without terminal cover.)
3
IDEC’s spring-up, fingersafe terminals enhance reliability and safety.
• Superior protection for a wide range of devices from sensitive electronic
equipment to electrical control circuits. Applications include semi-
conductor manufacturing equipment, electronic controllers, computers,
microprocessors, communications equipment, power supplies, machine
tools, motors, office equipment, and more.
• Excellent tripping time curve performance
• Flat retractable lever for safety operations
• Slim housing design
• Spring-up terminals
• Fingersafe main circuit terminals
• Color (red/green) contact position indicator
• DIN rail or direct panel mounting (through-panel mounting brackets
available)
• One and two pole models have both AC and DC voltages in each device
• Auxiliary / alarm contacts
Applicable Standards
UL1077
CSA C22.2 No. 235
EN60934
GB17701-1999
Electrical Applicance and
Material Safety Law
Technical Standard
Series Trip
Relay Trip
Certification Mark
Certification Organization
(File No.)
E68029
LR83454
B07 09 13332 063
European Commission's
Low Voltage Directive
No. 2008010307265840
JET
NC1V Circuit Breakers
Note: TÜV, CE, and CCC marks are applicable for series trip type only.
Specifications
Operator Style
Internal Circuit
Protection Method
No. of Poles
Rated Voltage (AC/DC)
Note 1
Rated Short-circuit
Capacity
Series Trip
Rated Current
(Current Trip)
Operation Characteristics
Note 2
Relay Trip
(Voltage Trip)
Note 3
Auxiliary Contact/
Alarm Contact
Rated Current
Trip Voltage
Contact Rating
Minimum Applicable Load
Insulation Resistance
Dielectric Strength
Vibration Resistance
(with rated current applied)
Shock Resistance
(S time delay curve: 80% rated current,
A, M time delay curve: 100% rated current)
Electrical Life
Reference Temperature
Operating Temperature
Operating Humidity
Main Circuit Terminal
Terminal Style Auxiliary/Alarm Contacts,
Voltage Coil Terminal
Weight (approx.)
Series trip (current trip), Relay trip (voltage trip)
Hydraulic magnetic tripping system, Magnetic tripping system (voltage trip)
1-pole
2-pole
3-pole
250V AC 50/60Hz, 65V DC
250V AC 50/60Hz, 125V DC
250V AC, 50/60Hz
250V AC, 2500A
250V AC, 2500A
250V AC, 2500A
65V DC, 2500A
125V DC, 2500A
0.1A, 0.3A, 0.5A, 1A, 2A, 3A, 5A, 7A, 10A, 15A, 20A, 25A, 30A
Time delay curve curve M (slow), curve A (medium), S (instantaneous)
Curves M and A are also available with inertia delay option.
30A
24 to 48V DC (at 25°C)
Voltage application duration 10 sec maximum, tripping time 0.1 sec maximum (at rated voltage)
125V AC 3A (resistive load), 30V DC 2A (resistive load)
24V DC 1mA (resistive load, reference value)
100MΩ minimum (500V DC megger)
2,000V AC, 1 minute (between terminals when main contacts are open, between live parts of different
poles, between live and dead parts)
600V AC (between terminals when auxiliary circuits are open)
Damage limits:
147 m/s
2
(10 to 55 Hz) (1-pole, 2-pole), 78 m/s
2
(3-pole)
Operating extremes: 98 m/s
2
(1-pole, 2-pole), 78 m/s
2
(3-pole)
Damage limits:
490 m/s
2
(1-pole, 2-pole), 297 m/s
2
(3-pole)
Operating extremes: 196 m/s
2
(S, A, M types)
10,000 cyles minimum (at rated curent), 10 operations per minute
40°C
−10 to +60°C (no freezing)
Rated current is based on an ambient temperature of 40°C. When the operating temperature exceeds
40°C, derate the rated current by using the factors shown below.
45 to 85% RH (no condensation)
Spring-up, fingersafe terminal: M4 screw (up to 20A), M5 screw (25A and 30A)
M3.5 screw
1-pole: 90g, 2-pole: 170g, 3-pole: 260g
Operating Temp. Derating Factor
50°C
0.9
55°C
0.8
60°C
0.7
Retractable lever
Note 1: 3-pole type is for AC voltage only.
Note 2: For S (instantaneous) tripping curve, humming sound may occur when used in an AC sinusoidal-wave current circuit around 80% of the
rated current, however, the performance of the circuit breaker will not be affected.
To avoid unnecessary tripping, do not use in circuits where inrush currents may be present.
Note 3: Relay trip (voltage trip) type is not equipped with an overcurrent trip function.
•
Do not use the NC1V circuit breakers in environments where they are exposed to extreme temperature, humidity, dust, corrosive gases,
vibration, shock, or in a circuit where inrush current may be present, otherwise unnecessary operation and damage may occur.
4
NC1V Circuit Breakers
Part No. Configuration
NC1V - 2 1 00 F - 30A A DC24V
1
Type
NC1V: Lever style
DIN rail and panel mounting
2
No. of Poles
1: 1-pole
2: 2-pole
3: 3-pole
3
Internal Circuit
1: Series trip (current trip)
5: Relay trip (voltage trip)
•
Specify rated current, time delay curve, or voltage trip coil voltage in place of
6 7 8
when ordering.
Internal
Circuit
No. of
Poles
Inertia
Delay
Auxiliary Contact
Alarm Contact
—
–
1-pole
With
One Auxiliary Contact
One Alarm Contact
—
One Auxiliary Contact
One Alarm Contact
—
One Auxiliary Contact
—
Two Auxiliary Contacts
One Alarm Contact
2-pole
One Auxiliary Contact
and One Alarm Contact
—
One Auxiliary Contact
With
Series Trip
(Current Trip)
Two Auxiliary Contacts
One Alarm Contact
One Auxiliary Contact
and One Alarm Contact
—
One Auxiliary Contact
Two Auxiliary Contacts
—
Three Auxiliary Contacts
One Alarm Contact
One Auxiliary Contact
and One Alarm Contact
Two Auxiliary Contacts
and One Alarm Contact
—
One Auxiliary Contact
Two Auxiliary Contacts
With
Three Auxiliary Contacts
One Alarm Contact
One Auxiliary Contact
and One Alarm Contact
Two Auxiliary Contacts
and One Alarm Contact
Relay Trip
(Voltage Trip)
1-pole
2-pole
3-pole
—
—
Part No.
NC1V-1100-
6 7
NC1V-1111-
6 7
NC1V-1121
6 7
NC1V-1100F-
6 7
NC1V-1111F-
6 7
NC1V-1121F-
6 7
NC1V-2100-
6 7
NC1V-2111-
6 7
NC1V-2112-
6 7
NC1V-2121-
6 7
NC1V-2131-
6 7
NC1V-2100F-
6 7
NC1V-2111F-
6 7
NC1V-2112F-
6 7
NC1V-2121F-
6 7
NC1V-2131F-
6 7
NC1V-3100-
6 7
NC1V-3111-
6 7
NC1V-3112-
6 7
NC1V-3113-
6 7
NC1V-3121-
6 7
NC1V-3131-
6 7
NC1V-3132-
6 7
NC1V-3100F-
6 7
NC1V-3111F-
6 7
NC1V-3112F-
6 7
NC1V-3113F-
6 7
NC1V-3121F-
6 7
NC1V-3131F-
6 7
NC1V-3132F-
6 7
NC1V-1500-
8
NC1V-2500-
8
NC1V-3500-
8
—
—
DC24V
0.1A
0.3A
0.5A
1A
2A
3A
5A
7A
10A
15A
20A
25A
30A
Code
Models
4
Auxiliary/Alarm Contacts
00: None
11: With one auxiliary contact
12: With two auxiliary contacts
13: With three auxiliary contacts
21: With one alarm contact
31: With one auxiliary contact and one alarm contact
32: With two auxiliary contacts and one alarm contact
8
Voltage Trip Coil Voltage
DC24V: 24-48V DC
* Specified
for relay trip only.
7
Time Delay Curve
M: Slow
A: Medium
S: Instantaneous
*
For both AC/DC.
*
Specified for series trip only.
6
Rated Current
0.1A, 0.3A, 0.5A, 1A, 2A, 3A,
5A, 7A, 10A 15A, 20A, 25A, 30A
* Specified
for series trip only.
5
Inertia Delay
Blank: Without
F:
With
*
Inertia delay is for AC voltage only.
*
Available with medium and slow types
(not applicable with relay trip).
6
Rated
Current
7
Time Delay
Curve
8 Voltage Trip
Coil Voltage
M (slow)
A (medium)
S (instantaneous)
—
3-pole
Note: Inertia delay is for an AC circuit. Also, time delay curve of S (instantaneous) is not available with inertia delay.
5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
