REVISIONS
LTR
A
B
DESCRIPTION
Add device type 02. Inactivate device type 01 (no approved source of
supply).
Add device types 03 through 07. Add vendors CAGE 32116, 5Y243,
57363, and 88379. Changed to reflect MIL-H-38534 processing.
Editorial changes throughout.
Add device type 08. Add vendor CAGE 8K957. Editorial changes
throughout.
Corrections to table I and figure 3. Editorial changes throughout.
Changes in accordance with NOR 5962-R189-92.
Redrawn with changes. Add case outlines U and Z. Add device type
09. Editorial changes throughout.
Changes in accordance with NOR 5962-R110-94.
Changes in accordance with NOR 5962-R013-96.
Not used.
Not used.
Incorporated NOR's 5962-R110-94 and 5962-R013-96. Made
changes to table I for device type 07. Redraw entire document.
Inactivate device types 03, 04, and 07 for new design. Add device
type 10.
Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add T
C
.
Table I, Total current, I
CC1
-SB, I
CC1
-25, I
CC1
-50, I
CC1
-100 for device
type 05; change the maximum limit from 25 mA to 60 mA. (4 places)
-gz
DATE (YR-MO-DA)
88-09-20
89-12-04
APPROVED
M. A. Frye
W. Heckman
C
D
E
F
G
H
J
K
L
M
N
P
91-01-16
92-03-03
92-04-27
92-11-11
94-02-17
95-12-15
W. Heckman
Alan Barone
Gregory A. Lude
K. A. Cottongim
Kendall A. Cottongim
Kendall A. Cottongim
96-06-20
98-01-28
04-11-05
07-05-10
K. A. Cottongim
K. A. Cottongim
Raymond Monnin
Robert M. Heber
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
P
15
P
16
P
17
P
18
REV
SHEET
P
19
P
20
P
21
P
1
P
2
P
3
P
4
P
5
P
6
P
7
P
8
P
9
P
10
P
11
P
12
P
13
P
14
PREPARED BY
Donald R. Osborne
CHECKED BY
D. A. Di Cenzo
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
APPROVED BY
N. A. Hauck
MICROCIRCUIT, HYBRID, DIGITAL, DUAL
CHANNEL, 15 VOLT, DRIVER-RECEIVER,
RECEIVER IDLE NORMALLY LOW
DRAWING APPROVAL DATE
87-08-06
REVISION LEVEL
P
SIZE
A
SHEET
CAGE CODE
67268
1 OF
21
5962-87579
DSCC FORM 2233
APR 97
5962-E409-07
1. SCOPE
1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with
MIL-PRF-38534 and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying
Number (PIN).
1.2 PIN. The PIN shall be as shown in the following example:
5962-87579
⎮
⎮
⎮
Drawing number
01
⎮
⎮
⎮
Device type
(see 1.2.1)
X
⎮
⎮
⎮
Case outline
(see 1.2.2)
X
⎮
⎮
⎮
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows:
Device type
01
02
03
04
05
06
07
08
09
10
2/
3/
3/
4/
3/
Generic number
BUS-63125, BUS-63126
BUS-63125II, BUS-63126II
ARX2411
ARX3411
NHI-1500
FC 1553623
CT-1487-D
MR63125M
FC 1553621
ACT-4487-D
Circuit function 1/
Dual channel driver-receiver
Low power, dual channel driver-receiver
Dual channel driver-receiver
Low power, dual channel driver-receiver
Low power, dual channel driver-receiver
Low power, dual channel driver-receiver with thermal protection
Low power, dual channel driver-receiver
Low power, dual channel driver-receiver
Low power, dual channel driver-receiver
Low power, dual channel driver-receiver
1.2.2 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows:
1.2.3 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
U
X
Y
Z
Descriptive designator
See figure 1
See figure 1
See figure 1
See figure 1
Terminals
28
36
36
28
Package style
Dual-in-line
Dual-in-line
Flat package
Flat package
1.2.4 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1/
2/
3/
4/
Interfaces with Manchester encoder-decoder described in Standard Microcircuit Drawing 78029.
Inactive for new design as of revision A, dated 88 SEP 20.
Device types 03, 04, and 07 are inactive for new design. Device type 10 replaces device types 03, 04, and 07.
For device type 06 only, the thermal protection operation is as follows:
With the thermal override pins 4 and 13 disconnected transmission amplitude decreases as case temperature exceeds
approximately 175°C and is restored as case temperatures decreases. With pins 4 and 13 connected to 0 volts this feature
is effectively disabled.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
P
5962-87579
SHEET
2
DSCC FORM 2234
APR 97
1.3 Absolute maximum ratings. 1/
Supply voltage range:
V
CC
(devices 01, 03, 04, 05, 07, 08, and 10) ..........................
V
EE
(devices 01-04, 06, 07, 08, 09, and 10) ...........................
V
CC1
(all devices) ....................................................................
Logic input voltage .....................................................................
Receiver differential voltage.......................................................
Receiver common mode voltage range .....................................
Driver peak output current .........................................................
Power dissipation (P
D
) at T
C
= +125°C:
(devices 01 and 08) ................................................................
(device 02)..............................................................................
(device 03)..............................................................................
(devices 04 and 10) ................................................................
(device 05)..............................................................................
(devices 06 and 09 .................................................................
(device 07)..............................................................................
Storage temperature range........................................................
Lead temperature (soldering, 10 seconds).................................
Junction temperature (T
J
):
(devices 01-04, 06, 07, 08, 09, and 10) ..................................
(device 05)..............................................................................
Thermal resistance, junction-to-case (θ
JC
):
(devices 01 and 05) ................................................................
(devices 02, 08, and 10) .........................................................
(device 03)..............................................................................
(device 04)..............................................................................
(devices 06 and 09) ................................................................
(device 07)..............................................................................
Thermal resistance, junction-to-ambient (θ
JA
):
(devices 01 and 05) ................................................................
(devices 02, 08, and 10) .........................................................
(device 03)..............................................................................
(device 04)..............................................................................
(devices 06 and 09) ................................................................
(device 07)..............................................................................
1.4 Recommended operating conditions.
Supply voltage range:
V
CC
(devices 01, 03, 04, 05, 07, and 10) ................................
V
CC
(device 08).......................................................................
V
EE
(devices 01-04, 06, 07, 09, and 10) .................................
V
EE
(device 08) .......................................................................
V
CC1
(all devices) ....................................................................
Logic input voltage .....................................................................
Receiver differential voltage:
(devices 01, 02, 03, 06, and 09) .............................................
(devices 04, 05, 07, 08, and 10) .............................................
Receiver common mode voltage range:
(devices 01, 02, 03, 04, 06, and 09) .......................................
(devices 05, 07, 08, and 10) ...................................................
Driver peak output current (all devices) .....................................
Serial data rate ..........................................................................
Junction temperature (T
J
):
(devices 01, 02, 03, 05, 06, 08, 09, and 10 ............................
(devices 04 and 07) ................................................................
Case operating temperature range (T
C
) .....................................
+14.25 V dc to +15.75 V dc
+11.25 V dc to +15.75 V dc
-14.25 V dc to -15.75 V dc
-11.25 V dc to -15.75 V dc
+4.5 V dc to +5.5 V dc
0 V dc to +5 V dc
30 V
P-P
40 V
P-P
-5 V dc to +5 V dc
-10 V dc to +10 V dc
180 mA
1.0 MHz maximum
+150°C
+160°C
-55°C to +125°C
-0.3 V dc to +18 V dc
+0.3 V dc to -18 V dc
-0.3 V dc to +7 V dc
-0.3 V dc to V
CC1
40 V
P-P
-10 V dc to +10 V dc
200 mA
4W
3W
3.3 W
2/
2W
2/
0.96 W 2/
1.65 W 2/
3W
-65°C to +150°C
+300°C
+160°C
+150°C
8.8°C/W
7.0°C/W
47.2°C/W
88°C/W
18°C/W
60°C/W
28.8°C/W
27.0°C/W
67.2°C/W
108°C/W
35°C/W
80°C/W
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade the performance and affect reliability.
2/ One channel transmitting at 100 percent duty cycle and the second channel is at standby.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
P
5962-87579
SHEET
3
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
MIL-HDBK-1553 - Multiplex Applications Handbook.
(Copies of these documents are available online at
http://assist.daps.dla.mil/quicksearch/
or
http://assist.daps.dla.mil
or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device class H shall be in accordance with MIL-
PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device
manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may
eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-
38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or
function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38534 and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Timing waveforms. The timing waveforms shall be as specified on figure 3.
3.2.4 Typical bus connections. The typical bus connections shall be as specified on figure 4.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
P
5962-87579
SHEET
4
DSCC FORM 2234
APR 97
3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DSCC-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets
the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a.
Burn-in test, method 1015 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified
in method 1015 of MIL-STD-883.
T
A
or T
C
as specified in the approved manufacturer's QM plan.
(2)
b.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
P
5962-87579
SHEET
5
DSCC FORM 2234
APR 97
PCB设计
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
