REVISIONS
LTR
A
B
C
DESCRIPTION
Editorial changes throughout. All references to classes B and S have been
deleted or changed to reflect the QML flow of the source of supply.
Update the boilerplate to current requirements as specified in MIL-PRF-38535.
Editorial changes throughout. – jak
Update vendor cage code and approved source of supply information in
bulletin page. Update DC V
CC
or GND current (I
CC
, I
GND
) per pin to section 1.3.
Update boilerplate paragraphs to current requirements of MIL-PRF-38535. –
MAA
DATE (YR-MO-DA)
95-11-13
06-11-06
13-06-20
APPROVED
Monica L. Poelking
Thomas M. Hess
Thomas M. Hess
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
C
15
C
16
REV
SHEET
PREPARED BY
Wanda L. Meadows
CHECKED BY
Thomas J. Ricciuti
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
C
10
C
11
C
12
C
13
C
14
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
APPROVED BY
Monica L. Poelking
DRAWING APPROVAL DATE
93-02-23
MICROCIRCUIT, DIGITAL, ADVANCED CMOS,
OCTAL BUFFER/LINE DRIVER WITH
NONINVERTING THREE-STATE OUTPUTS,
MONOLITHIC SILICON
SIZE
CAGE CODE
REVISION LEVEL
AMSC N/A
C
A
67268
SHEET
5962-92176
1 OF 16
5962-E110-13
DSCC FORM 2233
APR 97
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and
M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part
or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN.
1.2 PIN. The PIN is as shown in the following example:
5962
-
92176
01
M
R
A
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
/
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
Generic number
54ACQ244
Circuit function
Octal buffer/line driver with noninverting
three-state outputs
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-
JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Certification and qualification to MIL-PRF-38535
Q or V
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
R
S
2
Descriptive designator
GDIP1-T20 or CDIP2-T20
GDFP2-F20 or CDFP3-F20
CQCC1-N20
Terminals
20
20
20
Package style
Dual-in-line
Flat pack
Square leadless chip carrier
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-92176
SHEET
C
2
1.3 Absolute maximum ratings. 1/ 2/ 3/
Supply voltage range (V
CC
) ...........................................................................
DC input voltage range (V
IN
) .........................................................................
DC output voltage range (V
OUT
) ....................................................................
DC input clamp current (I
IK
):
V
IN
= -0.5 V .................................................................................................
V
IN
= V
CC
+ 0.5 V.........................................................................................
DC output clamp current (I
OK
):
V
OUT
= -0.5 V...............................................................................................
V
OUT
= V
CC
+ 0.5 V ......................................................................................
DC output current (I
OUT
) (per output pin) .......................................................
DC V
CC
or GND current (I
CC
, I
GND
) (per pin) ..................................................
Storage temperature range (T
STG
) ................................................................
Lead temperature (soldering, 10 seconds) ...................................................
Thermal resistance, junction-to-case (Θ
JC
) ...................................................
Junction temperature (T
J
) .............................................................................
Maximum power dissipation (P
D
) ..................................................................
1.4 Recommended operating conditions. 2/ 3/
Supply voltage range (V
CC
) ...........................................................................
Input voltage range (V
IN
) ...............................................................................
Output voltage range (V
OUT
)..........................................................................
Minimum high level input voltage (V
IH
):
V
CC
= 3.0 V .................................................................................................
V
CC
= 4.5 V .................................................................................................
V
CC
= 5.5 V .................................................................................................
Maximum low level input voltage (V
IL
):
V
CC
= 3.0 V .................................................................................................
V
CC
= 4.5 V .................................................................................................
V
CC
= 5.5 V .................................................................................................
Case operating temperature range (T
C
) ........................................................
Minimum input edge rate (∆V/∆t):
(V
IN
from 0.3V
CC
to 0.7V
CC
or from 0.7V
CC
to 0.3V
CC
) ................................
Maximum high level output current (I
OH
):
V
CC
= 3.0 V .................................................................................................
V
CC
= 4.5 V .................................................................................................
Maximum low level output current (I
OL
):
V
CC
= 3.0 V .................................................................................................
V
CC
= 4.5 V .................................................................................................
+3.0 V dc to +5.5 V dc
0.0 V to V
CC
0.0 V to V
CC
2.1 V
3.15 V
3.85 V
0.9 V
1.35 V
1.65 V
-55°C to +125°C
125 mV/ns
-12 mA
-24 mA
+12 mA
+24 mA
-0.5 V dc to +7.0 V dc
-0.5 V dc to V
CC
+ 0.5 V dc
-0.5 V dc to V
CC
+ 0.5 V dc
-20 mA
+20 mA
-20 mA
+20 mA
±50
mA
±50
mA
-65°C to +150°C
+300°C
See MIL-STD-1835
+175°C
500 mW
1/ Stresses above the absolute maximum rating may cause permanent damage to the device, Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ Unless otherwise noted, all voltages are referenced to GND.
3/ The limits for the parameters specified herein shall apply over the full specified V
CC
range and case temperature
range of -55°C to +125°C.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-92176
SHEET
C
3
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
http://quicksearch.dla.mil/
or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein.
Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.
JEDEC – SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC)
JEDEC Standard JESD20 - Standard for Description of 54/74ACXXXX and 54/74ACTXXXX Advanced High-Speed
CMOS Devices.
(Copies of these documents are available online at
http://www.jedec.org
or from JEDEC – Solid State Technology Association,
3103 North 10th Street, Suite 240–S, Arlington, VA 22201.)
2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3.
3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specified on
figure 4.
3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-92176
SHEET
C
4
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of
supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-
PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of
product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing.
3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime's agent,
and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore
documentation shall be made available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 37 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-92176
SHEET
C
5
求职招聘
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
