Freescale Semiconductor
Technical Data
Document Number: MPC885EC
Rev. 7, 07/2010
MPC885/MPC880 PowerQUICC
Hardware Specifications
This hardware specification contains detailed information on
power considerations, DC/AC electrical characteristics, and
AC timing specifications for the MPC885/MPC880. The
MPC885 is the superset device of the MPC885/MPC880
family. The CPU on the MPC885/MPC880 is a 32-bit core
built on Power Architecture™ technology that incorporates
memory management units (MMUs) and instruction and
data caches. For functional characteristics of the
MPC885/MPC880, refer to the
MPC885 PowerQUICC
Family Reference Manual.
To locate published errata or updates for this document, refer
to the MPC875/MPC870 product summary page on our
website listed on the back cover of this document or, contact
your local Freescale sales office.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Maximum Tolerated Ratings . . . . . . . . . . . . . . . . . . . 9
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . 10
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Thermal Calculation and Measurement . . . . . . . . . . 12
Power Supply and Power Sequencing . . . . . . . . . . . 15
Layout Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Bus Signal Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 16
IEEE 1149.1 Electrical Specifications . . . . . . . . . . . 44
CPM Electrical Characteristics . . . . . . . . . . . . . . . . . 46
UTOPIA AC Electrical Specifications . . . . . . . . . . . 69
USB Electrical Characteristics . . . . . . . . . . . . . . . . . 71
FEC Electrical Characteristics . . . . . . . . . . . . . . . . . 71
Mechanical Data and Ordering Information . . . . . . . 75
Document Revision History . . . . . . . . . . . . . . . . . . . 85
© 2010 Freescale Semiconductor, Inc. All rights reserved.
Overview
1
Overview
The MPC885/MPC880 is a versatile single-chip integrated microprocessor and peripheral combination
that can be used in a variety of controller applications and communications and networking systems. The
MPC885/MPC880 provides enhanced ATM functionality, an additional fast Ethernet controller, a USB,
and an encryption block.
Table 1
shows the functionality supported by MPC885/MPC880.
Table 1. MPC885 Family
Cache (Kbytes)
Part
I Cache
MPC885
MPC880
8
8
D Cache
8
8
10BaseT
Up to 3
Up to 2
10/100
2
2
3
2
2
2
1
1
Serial ATM and
UTOPIA interface
Serial ATM and
UTOPIA interface
Ethernet
SCC
SMC
USB
ATM Support
Security
Engine
Yes
No
2
Features
The MPC885/MPC880 is comprised of three modules that each use the 32-bit internal bus: a MPC8xx
core, a system integration unit (SIU), and a communications processor module (CPM).
The following list summarizes the key MPC885/MPC880 features:
• Embedded MPC8xx core up to 133 MHz
• Maximum frequency operation of the external bus is 80 MHz (in 1:1 mode)
— The 133-MHz core frequency supports 2:1 mode only.
— The 66-/80-MHz core frequencies support both the 1:1 and 2:1 modes.
• Single-issue, 32-bit core (compatible with the Power Architecture definition) with thirty-two
32-bit general-purpose registers (GPRs)
— The core performs branch prediction with conditional prefetch and without conditional
execution.
— 8-Kbyte data cache and 8-Kbyte instruction cache (see
Table 1)
– Instruction cache is two-way, set-associative with 256 sets in 2 blocks
– Data cache is two-way, set-associative with 256 sets
– Cache coherency for both instruction and data caches is maintained on 128-bit (4-word)
cache blocks.
– Caches are physically addressed, implement a least recently used (LRU) replacement
algorithm, and are lockable on a cache block basis.
— MMUs with 32-entry TLB, fully associative instruction and data TLBs
— MMUs support multiple page sizes of 4, 16, and 512 Kbytes, and 8 Mbytes; 16 virtual address
spaces and 16 protection groups
— Advanced on-chip emulation debug mode
MPC885/MPC880 PowerQUICC Hardware Specifications, Rev. 7
2
Freescale Semiconductor
Features
•
•
•
•
•
•
•
Provides enhanced ATM functionality found on the MPC862 and MPC866 families and includes
the following:
— Improved operation, administration and maintenance (OAM) support
— OAM performance monitoring (PM) support
— Multiple APC priority levels available to support a range of traffic pace requirements
— Port-to-port switching capability without the need for RAM-based microcode
— Simultaneous MII (100BaseT) and UTOPIA (half- or full -duplex) capability
— Optional statistical cell counters per PHY
— UTOPIA L2-compliant interface with added FIFO buffering to reduce the total cell
transmission time and multi-PHY support. (The earlier UTOPIA L1 specification is also
supported.)
— Parameter RAM for both SPI and I
2
C can be relocated without RAM-based microcode
— Supports full-duplex UTOPIA master (ATM side) and slave (PHY side) operations using a split
bus
— AAL2/VBR functionality is ROM-resident
Up to 32-bit data bus (dynamic bus sizing for 8, 16, and 32 bits)
Thirty-two address lines
Memory controller (eight banks)
— Contains complete dynamic RAM (DRAM) controller
— Each bank can be a chip select or RAS to support a DRAM bank
— Up to 30 wait states programmable per memory bank
— Glueless interface to DRAM, SIMMS, SRAM, EPROMs, Flash EPROMs, and other memory
devices
— DRAM controller programmable to support most size and speed memory interfaces
— Four CAS lines, four WE lines, and one OE line
— Boot chip-select available at reset (options for 8-, 16-, or 32-bit memory)
— Variable block sizes (32 Kbytes–256 Mbytes)
— Selectable write protection
— On-chip bus arbitration logic
General-purpose timers
— Four 16-bit timers or two 32-bit timers
— Gate mode can enable/disable counting.
— Interrupt can be masked on reference match and event capture
Two fast Ethernet controllers (FEC)—Two 10/100 Mbps Ethernet/IEEE Std. 802.3™ CDMA/CS
that interface through MII and/or RMII interfaces
System integration unit (SIU)
— Bus monitor
— Software watchdog
MPC885/MPC880 PowerQUICC Hardware Specifications, Rev. 7
Freescale Semiconductor
3
Features
•
•
•
— Periodic interrupt timer (PIT)
— Clock synthesizer
— Decrementer and time base
— Reset controller
— IEEE Std 1149.1™ test access port (JTAG)
Security engine is optimized to handle all the algorithms associated with IPsec, SSL/TLS, SRTP,
IEEE Std 802.11i™, and iSCSI processing. Available on the MPC885, the security engine contains
a crypto-channel, a controller, and a set of crypto hardware accelerators (CHAs). The CHAs are:
— Data encryption standard execution unit (DEU)
– DES, 3DES
– Two key (K1, K2, K1) or three key (K1, K2, K3)
– ECB and CBC modes for both DES and 3DES
— Advanced encryption standard unit (AESU)
– Implements the Rijndael symmetric key cipher
– ECB, CBC, and counter modes
– 128-, 192-, and 256- bit key lengths
— Message digest execution unit (MDEU)
– SHA with 160- or 256-bit message digest
– MD5 with 128-bit message digest
– HMAC with either algorithm
— Crypto-channel supporting multi-command descriptor chains
— Integrated controller managing internal resources and bus mastering
— Buffer size of 256 bytes for the DEU, AESU, and MDEU, with flow control for large data sizes
Interrupts
— Six external interrupt request (IRQ) lines
— 12 port pins with interrupt capability
— 23 internal interrupt sources
— Programmable priority between SCCs
— Programmable highest priority request
Communications processor module (CPM)
— RISC controller
— Communication-specific commands (for example,
GRACEFUL STOP TRANSMIT
,
ENTER HUNT
MODE
, and
RESTART TRANSMIT
)
— Supports continuous mode transmission and reception on all serial channels
— 8-Kbytes of dual-port RAM
— Several serial DMA (SDMA) channels to support the CPM
— Three parallel I/O registers with open-drain capability
MPC885/MPC880 PowerQUICC Hardware Specifications, Rev. 7
4
Freescale Semiconductor
Features
•
•
•
•
•
On-chip 16
×
16 multiply accumulate controller (MAC)
— One operation per clock (two-clock latency, one-clock blockage)
— MAC operates concurrently with other instructions
— FIR loop—Four clocks per four multiplies
Four baud rate generators
— Independent (can be connected to any SCC or SMC)
— Allow changes during operation
— Autobaud support option
Up to three serial communication controllers (SCCs) supporting the following protocols:
— Serial ATM capability on SCCs
— Optional UTOPIA port on SCC4
— Ethernet/IEEE Std 802.3™ optional on the SCC(s) supporting full 10-Mbps operation
— HDLC/SDLC
— HDLC bus (implements an HDLC-based local area network (LAN))
— Asynchronous HDLC to support point-to-point protocol (PPP)
— AppleTalk
— Universal asynchronous receiver transmitter (UART)
— Synchronous UART
— Serial infrared (IrDA)
— Binary synchronous communication (BISYNC)
— Totally transparent (bit streams)
— Totally transparent (frame based with optional cyclic redundancy check (CRC))
Up to two serial management channels (SMCs) supporting the following protocols:
— UART (low-speed operation)
— Transparent
— General circuit interface (GCI) controller
— Provide management for BRI devices as GCI controller in time-division multiplexed (TDM)
channels
Universal serial bus (USB)—Supports operation as a USB function endpoint, a USB host
controller, or both for testing purposes (loop-back diagnostics)
— USB 2.0 full-/low-speed compatible
— The USB function mode has the following features:
– Four independent endpoints support control, bulk, interrupt, and isochronous data transfers.
– CRC16 generation and checking
– CRC5 checking
– NRZI encoding/decoding with bit stuffing
– 12- or 1.5-Mbps data rate
MPC885/MPC880 PowerQUICC Hardware Specifications, Rev. 7
Freescale Semiconductor
5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
