INCH-POUND
MIL-DTL-83723/73F
19 August 2009
SUPERSEDING
MIL-DTL-83723/73E
20 October 2000
DETAIL SPECIFICATION SHEET
CONNECTOR, ELECTRIC, (CIRCULAR, ENVIRONMENT RESISTING),
RECEPTACLE, (SINGLE HOLE MOUNT, BAYONET COUPLING, CRIMP SOCKET CONTACT)
(SERIES III, CLASSES A, G, M, R, T, W AND Z)
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein
shall consist of this specification sheet and MIL-DTL-83723.
FIGURE 1. Dimensions and configurations.
AMSC N/A
FSC 5935
MIL-DTL-83723/73F
Inches
.0025
.005
.008
.015
.018
.020
.022
.032
.042
.046
.052
.065
.069
.071
.072
.076
.084
.089
.090
.094
.097
.101
.106
.112
mm
0.06
0.13
0.20
0.38
0.46
0.51
0.56
0.81
1.07
1.17
1.32
1.65
1.75
1.80
1.83
1.93
2.13
2.26
2.29
2.39
2.46
2.57
2.69
2.84
Inches
.120
.125
.138
.144
.149
.198
.204
.211
.250
.259
.312
.366
.376
.378
.380
.388
.392
.428
.433
.490
.508
.530
.531
.535
mm
3.05
3.18
3.51
3.66
3.78
5.03
5.18
5.36
6.35
6.58
7.92
9.30
9.55
9.60
9.65
9.86
9.96
10.87
11.00
12.45
12.90
13.46
13.49
13.59
Inches
.536
.540
.558
.560
.561
.594
.627
.636
.654
.659
.696
.700
.705
.708
.719
.728
.769
.772
.774
.806
.812
.824
.829
.860
mm
13.61
13.72
14.17
14.22
14.25
15.09
15.93
16.15
16.61
16.74
17.68
17.78
17.91
17.98
18.26
19.49
19.53
19.61
19.66
20.47
20.62
20.93
21.06
21.84
Inches
.875
.893
.896
.898
.901
.906
.935
.937
.969
.985
1.002
1.007
1.020
1.025
1.062
1.070
1.108
1.125
1.126
1.127
1.131
1.132
1.156
1.187
mm
22.23
22.68
22.76
22.81
22.89
23.01
23.75
23.80
24.61
25.02
25.45
25.58
25.91
26.04
26.97
27.18
28.14
28.58
28.60
28.63
28.73
28.75
29.36
30.15
Inches
1.233
1.235
1.250
1.251
1.252
1.256
1.257
1.312
1.343
1.375
1.376
1.377
1.381
1.382
1.385
1.437
1.483
1.501
1.506
1.562
1.703
mm
31.32
31.37
31.75
31.78
31.80
31.90
31.93
33.32
34.11
34.93
34.95
34.98
35.08
35.10
35.18
36.50
37.66
38.13
38.25
39.67
43.26
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances are
±
.005 (0.13 mm) for three place decimals,
±
.01 (0.25 mm) for two place decimals and
±
1° for all angles.
4. Rear accessory interchangeability dimensions shall be accordance with SAE-AS85049.
5. The centerline of indicated projection must be located on vertical centerline
±
2°.
6. See table I for contact cavities requiring this dimension.
FIGURE 1. Dimensions and configurations - Continued.
5