Data downloaded from http://www.angliac.com - the website of Anglia - tel: 01945 474747
®
HIGH CURRENT 2LP
Low Profile Power Inductors
Description
• Compact footprint for high density, high current/low
voltage applications
• Foil technology that adds higher reliability factor over the
traditional magnet wire used for higher frequency circuit
designs
• Frequency Range up to 1MHz
Applications
• Next generation microprocessors
• Energy storage applications
• DC-DC converters
• Computers
Environmental Data
• Storage temperature range: -40C to +125C
• Operating ambient temperature range: -40C to +85C
(range is application specific).
• Infrared reflow temperature: +260C for 10 seconds
maximum
Part
Number
HC2LP-R47
HC2LP-R68
HC2LP-1R0
HC2LP-2R2
HC2LP-4R7
HC2LP-6R0
Rated
Inductance
µH
.47
.68
1.0
2.2
4.7
6.0
OCL (1)
µH ± 20%
.52
.63
1.15
2.00
4.55
6.00
Irms (2)
Amperes
(Typ.)
52.9
52.9
33.0
24.3
17.0
17.0
Packaging
• Supplied in tape and reel packaging, 44mm width,
130 parts per 13" reel
• 45 parts per tray, bulk packaging also available
Isat (3)
Amperes
(Typ.)
63.75
50.00
42.50
31.90
21.25
16.50
DCR (4)
Ohms
(Max.)
.0006
.0006
.0013
.0023
.0046
.0046
Volts (5)
µSec
6.87
6.87
10.31
13.75
20.62
20.62
1) Open Circuit Inductance Test Parameters: 300kHz, 0.250 Vrms, 0.0 Adc
2) DC current for an approximate temperature change of 40°C without core loss.
Derating is necessary for AC currents.
PCB layout, trace thickness and width, air-flow and proximity of other heat
generating components will affect the temperature rise.
It is recommended that the temperature of the part not exceed 125°C under
worst case operating conditions verified in the end application.
3) Peak current for approximately 30% roll-off
4) Values @ 20°C
5) Applied Volt-Time product (V-µS) across the inductor. This value represents the
applied V-µS at 300KHz necessary to generate a core loss equal to 10% of the
total losses for 40°C temperature rise.
Mechanical Diagrams
TOP VIEW
19.2
max
RECOMMENDED PCB PAD LAYOUT
FRONT VIEW
10.00
SCHEMATIC
9.5
typ
1
HC2LP-xxx
wwllyy R
19.00
11.18
max
2.8
typ
1
2
2
19.2
max
5.50
5.50
2.3
typ
Packaging Information
1.5Dia +0.10
-0.00
4.0
See Note 1
2.0
See Note 6
1.7
A
20.2
See note 6
19.3
1
HC2LP-xxx
wwllyy R
2
40.4
+/-0.1
44.0
+/-0.3
A
11.3
19.3
32
Dimensions in Millimeters
SECTION A-A
User direction of feed
Parts packaged on 13" Diameter reel,
130 parts per reel.
For the very latest product data and news visit angliac.com
Data downloaded from http://www.angliac.com - the website of Anglia - tel: 01945 474747
®
HIGH CURRENT 2LP
Low Profile Power Inductors
I
DC
DERATING WITH CORE LOSS
0
% of Losses from Irms (maximum)
20
40
50
60
70
80
30
0K
Hz
20
0K
Hz
50
0K
Hz
1M
Hz
90
92
94
95
96
97
98
99
10
20
30
40
50
60
80
100
200
300
400 500 600
800 1000
% of Applied Volt-µ-Seconds
INDUCTANCE VERSUS SATURATION CURRENT
100
90
80
70
% of OCL
60
50
40
30
20
10
0
0
20
40
60
80
100
120
140
160
180
200
% of I
SAT
PM-4114 4/03
© Cooper Electronic
Technologies 2003
Visit us on the Web at www.cooperET.com
3601 Quantum Boulevard Boynton Beach, Florida 33426-8638
Tel: +1-561-752-5000 Toll Free: +1-888-414-2645 Fax: +1-561-742-1178
This bulletin is intended to present product design solutions and technical information that will help the end user with design applications. Cooper
Electronic Technologies reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of
any products. Cooper Electronic Technologies also reserves the right to change or update, without notice, any technical information contained in this
bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
For the very latest product data and news visit angliac.com
10
0K
Hz
NXP MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
