REVISIONS
LTR
A
B
C
D
E
DESCRIPTION
Changes in accordance with NOR 5962-R104-98. - rrp
Add class T requirements. Update boilerplate. Redrawn. - rrp
Made changes to 1.5 and added new RHA designator P in table I. - rrp
Add device type 02. Make changes to 1.2.2, 1.5, table I, figure 1, and
appendix A. - ro
Made changes to figure 3. -rrp
DATE (YR-MO-DA)
98-05-11
98-12-09
99-04-19
99-11-24
00-01-03
APPROVED
R. MONNIN
R. MONNIN
R. MONNIN
R. MONNIN
R. MONNIN
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
E
15
E
16
E
17
E
18
REV
SHEET
PREPARED BY
SANDRA ROONEY
E
19
E
20
E
21
E
1
E
22
E
2
E
23
E
3
E
24
E
4
E
25
E
5
E
26
E
6
E
27
E
7
E
8
E
9
E
10
E
11
E
12
E
13
E
14
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
SANDRA ROONEY
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
APPROVED BY
MICHAEL A. FRYE
MICROCIRCUIT, LINEAR, RADIATION
HARDENED, CMOS, MULTIPLEXER WITH
OVERVOLTAGE PROTECTION, MONOLITHIC
SILICON
SIZE
A
SHEET
CAGE CODE
DRAWING APPROVAL DATE
96-01-10
AMSC N/A
REVISION LEVEL
E
67268
1 OF
27
5962-96742
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
5962-E094-00
1. SCOPE
1.1 Scope. This drawing documents three product assurance class levels consisting of high reliability (device classes Q and
M), space application (device class V) and for appropriate satellite and similar applications (device class T). A choice of case
outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of
Radiation Hardness Assurance (RHA) levels are reflected in the PIN. For device class T, the user is encouraged to review the
manufacturer’s Quality Management (QM ) plan as part of their evaluation of these parts and their acceptability in the intended
application.
1.2 PIN. The PIN is as shown in the following example:
5962
R
96742
01
V
E
X
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
/
\/
Drawing number
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
1.2.1 RHA designator. Device classes Q, T and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and
are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
Generic number
HS-508ARH
HS-508BRH
Circuit function
Radiation hardened DI CMOS single 8-
channel MUX with overvoltage protection
Radiation hardened DI CMOS single 8-
channel MUX with overvoltage protection
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant,
non-JAN class level B microcircuits in accordance with MIL-PRF-38535,
appendix A
Certification and qualification to MIL-PRF-38535
Certification and qualification to MIL-PRF-38535 with performance as specified
in the device manufacturers approved quality management plan.
Q, V
T
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
E
X
Descriptive designator
CDIP2-T16
CDFP4-F16
Terminals
16
16
Package style
Dual-in-line
Flat pack
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q, T and V or MIL-PRF-38535,
appendix A for device class M.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-96742
SHEET
E
2
1.3 Absolute maximum ratings. 1/
Supply voltage between +V and -V ............................................................................ 40 V
Supply voltage between +V and ground..................................................................... +20 V
Supply voltage between -V and ground...................................................................... -20 V
Digital input overvoltage:
+V
EN
, +V
A
............................................................................................................. +V
SUPPLY
+ 4 V
-V
EN
, -V
A
.............................................................................................................. -V
SUPPLY
- 4 V
Analog input overvoltage:
+V
S
........................................................................................................................ +V
SUPPLY
+20 V
-V
S
........................................................................................................................ -V
SUPPLY
-20 V
Peak current, S or D (pulsed at 1 ms, 10 percent duty cycle max)............................. 40 mA
Storage temperature range ........................................................................................ -65
C to +150
C
Maximum package power dissipation at T
A
= +125
C (P
D
): 2/
Case outline E......................................................................................................... 0.67 W
Case outline X......................................................................................................... 0.59 W
Thermal resistance, junction-to-case (
JC
):
Case outline E......................................................................................................... 12
C/W
Case outline X......................................................................................................... 25
C/W
Thermal resistance, junction-to-ambient (
JA
):
Case outline E......................................................................................................... 75
C/W
Case outline X......................................................................................................... 85
C/W
Lead temperature (soldering, 10 seconds)................................................................. +275
C
Junction temperature (T
J
)........................................................................................... +175
C
1.4 Recommended operating conditions.
Operating supply voltage (
V
SUPPLY
)........................................................................
15 V
Logic low level (V
AL
)................................................................................................... +0.8 V
Logic high level (V
AH
)................................................................................................. +4.0 V
Ambient operating temperature range (T
A
) ................................................................ -55
C to +125
C
1.5 Radiation features
SEP effective let no upset:
2
Device type 01 ........................................................................................................ 110 MEV/(cm / mg) 3/
Device type 02 ........................................................................................................ TBD
Maximum total dose available (dose rate = 50 – 300 rads(Si)/s)
Device classes Q and V:
Device type 01 ................................................................................................... 100 Krad (Si)
Device type 02 ................................................................................................... 300 Krad (Si)
Device type class T:
Device type 01 and 02 ....................................................................................... 100 Krad (Si)
Dose rate upset (20 ns pulse):
8
Device type 01 ........................................................................................................ >1 x 10 Rad(Si)/s
Device type 02 ........................................................................................................ Not tested
Latch-up...................................................................................................................... None 3/
1/
2/
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
If device power exceeds package dissipation capability, provide heat sinking or derate linearly (the derating is based on
JA
) at the following rates:
Case outline E.............................................................................13.3 mW/
C
Case outline X.............................................................................11.76 mW/
C
Guaranteed by process or design, not tested.
3/
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-96742
SHEET
E
3
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in
the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the
solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 -
MIL-STD-973 -
MIL-STD-1835 -
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings (SMD's).
Standard Microcircuit Drawings.
Test Method Standard Microcircuits.
Configuration Management.
Interface Standard For Microcircuit Case Outlines.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q, T and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A, as specified herein.
3.1.1 Microcircuit die. For the requirements for microcircuit die, see appendix A to this document.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q, T and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connection(s). The terminal connection(s) shall be as specified on figure 1.
3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 2.
3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figure 3.
3.2.5 Radiation exposure circuit. The radiation exposure circuit shall be as specified in table III.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-96742
SHEET
E
4
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space
limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the
RHA designator shall still be marked. Marking for device classes Q, T and V shall be in accordance with MIL-PRF-38535.
Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q, T and V shall be a "QML" or "Q" as
required in MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix
A.
3.6 Certificate of compliance. For device classes Q, T and V, a certificate of compliance shall be required from a
QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a
certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-
HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of
supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q, T and V, the requirements of
MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q, T and V in MIL-PRF-38535 or
for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
herein) involving devices acquired to this drawing is required for any change as defined in MIL-STD-973.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain
the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 82 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-96742
SHEET
E
5
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
