)......................................... 2.5V to 5.5V
Enable Voltage (V
EN
).............................................. 0V to V
IN
Junction Temperature (T
J
) ........................ –40°C to +125°C
Junction Thermal Resistance
1.6 x1.6 Thin MLF-6 (θ
JA
) ...............................92.4°C/W
Electrical Characteristics
(5)
V
IN
= V
EN
= V
OUT
+ 1V; C
IN
= C
OUT
= 1µF; I
OUT
= 100µA; T
J
= 25°C,
bold
values indicate –40°C to +125°C, unless noted.
Parameter
Output Voltage Accuracy
Line Regulation
Load Regulation
Dropout Voltage
(6)
(7)
Condition
Variation from nominal V
OUT
Variation from nominal V
OUT
; –40°C to +125°C
V
IN
= V
OUT
+1V to 5.5V; I
OUT
= 100µA
I
OUT
= 100µA to 150mA
I
OUT
= 50mA
I
OUT
= 150mA
(8)
Min
–2.0
–3.0
Typ
Max
+2.0
+3.0
Units
%
%
%
%
mV
mV
µA
µA
dB
dB
0.02
0.3
60
180
29
0.05
65
55
200
325
200
30
0.3
1
135
380
39
1
Ground Pin Current
Ripple Rejection
Current Limit
I
OUT
= 0mA
V
EN
≤
0.2V
f = up to 1kHz; C
OUT
= 1µF
f = 1kHz – 10kHz; C
OUT
= 1µF
V
OUT
= 0V
C
OUT
= 1µF, 10Hz to 100kHz
MIC5368 Only; V
EN
= 0V; V
IN
= 3.6V; I
OUT
= –3mA
Ground Pin Current in Shutdown
550
mA
µV
RMS
Ω
Output Voltage Noise
Auto-Discharge NFET
Resistance
Enable Input
Enable Input Voltage
Enable Input Current
Turn-on Time
Logic Low
Logic High
V
IL
≤
0.2V
V
IH
≥
1.2V
C
OUT
= 1µF; I
OUT
= 150mA
1.2
0.01
0.01
50
0.2
1
1
125
V
V
µA
µA
µs
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. The maximum allowable power dissipation of any T
A
(ambient temperature) is P
D(max)
= (T
J(max)
– T
A
) /
θ
JA
. Exceeding the maximum allowable power
dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
4. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF.
5. Specification for packaged product only.
6. Regulation is measured at constant junction temperature using low duty cycle pulse testing; changes in output voltage due to heating effects are
covered by the thermal regulation specification.
7. Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value measured at 1V differential.
For outputs below 2.5V, dropout voltage is the input-to-output differential with the minimum input voltage 2.5V.
8. Ground pin current is the regulator quiescent current. The total current drawn from the supply is the sum of the load current plus the ground pin
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
