All product names are trademarks of their respective companies
Fluke-725 Multifunction Process Calibrators:
The Fluke-700P00 and
P27 Pressure Modules will display correct pressure readings when
used with Fluke-725 Multifunction Process Calibrators at internal
software revision 1.9 and later. To view the software revision, power-on
the calibrator while holding down the 0% key. Read the REV number in
the display. Contact your Fluke Service Center for a free update of
calibrators with lower revision numbers. Reference PCN 4578.
Protecting Yourself from Pressure Releases
To avoid a violent release of pressure in a pressurized system, shut off
the isolation valve and slowly bleed off the pressure before you attach
or remove the pressure module from the pressure line.
Avoiding Overpressure Damage
Applying pressure in excess of the BURST PRESSURE specified on
the pressure module can destroy the pressure module. Burst pressure
is 3X full scale (2X for 700P09, 30X for 700P00).
Box Contents
Pressure module, strap, 1/4 NPT to 1/4 ISO metric adapters, instruction
sheet.
Table 1. Pressure Module Specifications
MODEL
FLUKE-700P00
RANGE
2
1
GAGE OR
DIFFERENTIAL
Differential
ISOLATED OR
NONISOLATED
Nonisolated
REFERENCE
UNCERTAINTY
(23° ± 3°C)
0.300%
STABILITY
(1 YEAR)
0.025%
TEMP
(0° to 50°C)
0.025%
TOTAL UNCERTAINTY
(% of Full Scale) 1 YEAR
0.350%
3
FLUKE-700P01
FLUKE-700P02
FLUKE-700P03
FLUKE-700P04
FLUKE-700P05
FLUKE-700P06
FLUKE-700P27
FLUKE-700P07
FLUKE-700P08
FLUKE-700P09
0 to 1.000 in H
2
O
0 to 0.249 kPa
0 to 0.002 bar
0 to 10.00 in H
2
O
0 to 2.49 kPa
0 to 0.02 bar
0 to 1.0000 psi
0 to 6.8900 kPa
0 to 6.89 E–2 bar
0 to 5.0000 psi
0 to 34.000 kPa
0 to 0.3400 bar
0 to 15.000 psi
0 to 100.00 kPa
0 to 1.0000 bar
0 to 30.000 psi
0 to 200.00 kPa
0 to 2.0000 bar
0 to 100.00 psi
0 to 700.00 kPa
0 to 7.0000 bar
0 to 300.00 psi
0 to 2000.0 kPa
0 to 20.000 bar
0 to 500.00 psi
0 to 3400.0 kPa
0 to 34.000 bar
0 to 1000.0 psi
0 to 7000.0 kPa
0 to 70.000 bar
0 to 1500.0 psi
0 to 10000.0 kPa
0 to 100.000 bar
Differential
Nonisolated
0.200%
0.050%
0.050%
0.300%
Differential
Nonisolated
0.150%
0.070%
0.080%
0.300%
Differential
Nonisolated
0.050%
0.020%
0.030%
0.100%
Differential
Nonisolated
0.025%
0.010%
0.015%
0.050%
Gage
Isolated
0.025%
0.010%
0.015%
0.050%
Gage
Isolated
0.025%
0.010%
0.015%
0.050%
Gage
Isolated
0.025%
0.010%
0.015%
0.050%
Gage
Isolated
0.025%
0.010%
0.015%
0.050%
Gage
Isolated
0.025%
0.010%
0.015%
0.050%
Gage
Isolated
0.025%
0.010%
0.015%
0.050%
1.
2.
3.
4.
5.
6.
Use of pressure zero function is required to achieve these specifications. Contact your Fluke Service Center for upgrade of your Fluke 701 or Fluke 702 V1.0, V1.1, or
V1.2 calibrator.
2
Available pressure units (psi, kPa, bar, inHg, mmHg, inH
2
0, ftH
2
0., kg/cm , mmH
2
0, cmH
2
0) are determined by the calibrator being used.
Accuracy specifications apply for 0 to 100% of full scale, 0 to 50°C. 1% FS typical, -10 to 0°C. On 700P00 only, specification applies from 15 to 35
°
C.
Maximum Non-Destructive Pressure: 3X maximum rated pressure, including common mode pressure. (700P09: 2X, 700P00: 30X)
Maximum Common Mode Pressure: 3X maximum rated pressure. (700P09: 2X, 700P00: 30X)
Specifications reflect a confidence interval of 95%.
Avoiding Mechanical Damage
To avoid mechanically damaging the pressure module, never apply
more than 10 ft.-lbs. of torque between the pressure module fittings or
between the fittings and the body of the module. Always apply
appropriate torque between the pressure module fitting and connecting
fittings or adapters. Figure 2 shows the correct way and incorrect
ways to use a wrench when applying torque to the pressure module
fitting.
Performance Test
If you need to check that the pressure module meets its accuracy
specification, use a dead weight tester or suitable pressure calibrator.
The accuracy of the dead weight tester or pressure calibrator should
be at least 4X better than the 700 Series pressure specification.
Proceed as follows to verify that a pressure module is operating within
specification:
1.
Read the pressure value with no externally applied pressure to
make sure the 0% of scale is correct. When reading the pressure
with a 700 Series, press the ZERO key to remove any zero
offset.
Connect the pressure module to a dead weight tester.
Set the dead weight tester to 20% of the pressure module’s full
scale value.
Make sure the reading agrees with the dead weight tester value
within the Total Uncertainty specification in Table 1.
Set the dead weight tester to 40, 60, 80, and 100% of full scale
and compare the respective readings.
If temperature sensitivity is of concern, repeat steps 1 through 5
at various controlled temperatures.
G
AN
R
E
10
70
04
RE
0P
SU
ES
PR
DU
/G
MO
ID
bar
PS
a 1
15
0 kP
LE
2.
3.
4.
5.
6.
yz2f.eps
Figure 2.
Pressure Calibration Kit
The Fluke-700PCK Pressure Calibration Kit makes it possible to
calibrate pressure modules at ambient temperature with a precision
pressure calibrator or dead weight tester at least 4x better than the
module specification. A 386 or better PC and Windows® 3.1 or better
are required. The kit is an optional accessory available from your
distributor or Fluke.
Avoiding Corrosion Damage
To avoid damaging the pressure module from corrosion, use it only
with specified media as shown below:
•
Isolated modules: any medium that is compatible with type 316
51单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
