Maxim
>
Design Support
>
Technical Documents
>
Subsystem Boards
> APP 5563
Keywords:
Fresno, MAXREFDES11, subsystem reference design, analog front end, AFE, industrial sensors,
isolated power and data, industrial automation, PLC, medical
SUBSYSTEM BOARD 5563
Fresno (MAXREFDES11#): 16-Bit High-Accuracy 0 to
10V Input Isolated Analog Front End (AFE)
Jan 19, 2013
Abstract: This document explains how the Fresno (MAXREFDES11#) subsystem reference design meets the
higher resolution and higher voltage needs of industrial control and industrial automation applications. Hardware
and firmware design files as well as FFTs and histograms from lab measurements are provided.
Introduction
Low resolution and low input voltage
analog-to-digital converters (ADCs) are
integrated in many of today's field
programmable gate arrays (FPGAs) and
microcontrollers. However, they fall short
on meeting the needs of industrial control
More detailed image
(JPG)
and industrial automation applications that
require higher resolutions and higher input
voltages. The Fresno (MAXREFDES11#) subsystem reference design is a 16-bit high-accuracy industrial
analog front end (AFE) that accepts 0 to 10V signals and features isolated power and data—all integrated into a
small form factor. The Fresno design integrates an ultra-precision low-noise buffer (MAX44250); a highly
accurate ADC (MAX11100); an ultra-high-precision 4.096V voltage reference (MAX6126); 600V
RMS
data
isolation (MAX14850); and isolated/regulated +5.5V, +5V, and -3V power rails (MAX256/MAX1659/MAX1735).
This AFE solution can be used in any application that needs high-accuracy analog-to-digital conversion, but it is
mainly targeted for industrial sensors, industrial automation, process control, programmable logic controllers
(PLCs), and medical applications.
Page 1 of 11
Figure 1. The Fresno subsystem design block diagram.
Features
High accuracy
0 to 10V input range
Isolated power and data
Small printed circuit board (PCB) area
Device drivers
Example C source code
Pmod
™
-compatible form factor
Applications
Industrial sensors
Process control
Industrial automation
PLC
Medical
Detailed Description of Hardware
The Pmod specification allows for both 3.3V and 5V modules as well as various pin
assignments. This module is designed only for a supply voltage of 3.3V and uses
the SPI pin assignments as illustrated on the right.
The power requirements are shown in
Table 1.
The currently supported platforms
and ports are shown in
Table 2.
Page 2 of 11
Table 1. Power Options for the Fresno Subsystem Reference Design
Power Type
On-board isolated power
Jumper Shunt
JU1: 1–2
JU2: 2–3
JU3: 1–2
JU1: 2–3
JU2: 1–2
JU3: 2–3
Input Voltage (V)
3.3
6
-5
Input Current (mA, typ)
71
10
2
External power
Table 2. Supported Platforms and Ports
Supported Platforms
Nexys
™
3 platform (Spartan
®
-6)
ZedBoard
™
platform (Zynq
®
-7020)
Port
JB1
JA1
The Fresno hardware design provides isolated power (MAX256) and isolated data (MAX14850) for a high-
accuracy, 0 to 10V signal, analog-to-digital conversion application.
The MAX44250 (U1) op amp input circuit attenuates and buffers a 0 to10V signal to match the input range of
the ADC (MAX11100), which is 0 to 4.096V.
The MAX11100 (U2) is a 16-bit, successive-approximation register (SAR) ADC with AutoShutdown
™
and fast
1.1µs wake-up features. The ADC's reference input is driven by an ultra-high-precision 4.096V voltage
reference, the MAX6126 (U3), with 0.02% initial accuracy and a 3ppm/°C maximum temperature coefficient
(tempco).
The MAX256 (U4) provides an isolated, functional insulation class power solution that accepts 3.3V and
converts it to ±6V using an off-the-shelf TGN-H251NF Halo
®
transformer with a 1:1 primary to secondary turns
ratio plus an external on-board voltage-doubler circuit. Post-regulation is accomplished using the MAX1659 low
dropout (LDO) regulator (for +5V) and the MAX1735 low dropout (LDO) regulator (for -3V). Data isolation is
accomplished using the MAX14850 (U5) digital data isolator. The combined power and data isolation achieved
is 600V
RMS
.
The signal input impedance of the Fresno subsystem is 5kΩ (R19 + R20). Ideally, the input impedance should
be high, but larger resistors induce higher thermal noise and degrade the noise performance. Therefore, the
values of the input resistors R19 and R20 are application dependent. Note that when choosing different values
for the input resistors to properly attenuate a 10V signal to a 4V signal, R19 = 1.5 × R20.
To use the on-board isolated power supplies, move the shunts on jumper JU1 and JU3 to the 1–2 position and
move the shunt on jumper JU2 to the 2–3 position. To use an external power supply, move the shunts on
jumper JU1 and JU3 to the 2–3 position and move the shunt on jumper JU2 to the 1–2 position. Connect the
ground terminal of the external power supply to the GND2 connector, the +6V to +12V supply to the EXT_V+
connector, and the -3.3V to -5V supply to the EXT_V- connector. See Table 1 for the jumper settings and the
input current requirements.
Detailed Description of Firmware for Nexys 3 Platform
The Fresno firmware design was initially released for the Nexys 3 development kit and targeted a Microblaze
™
Page 3 of 11
soft core microcontroller placed inside a Xilinx
®
Spartan-6 FPGA. Support for additional platforms may be
added periodically under
Firmware Files
in the
All Design Files
section. The currently supported platforms and
ports are shown in Table 2.
The firmware is a working example of how to interface to the hardware, collect samples, and save them to
memory. The simple process flow is shown in
Figure 2.
The firmware is written in C using the Xilinx SDK tool,
which is based on the Eclipse
™
open source standard. Custom Fresno-specific design functions were created
utilizing the standard Xilinx XSpi core version 3.03a. The SPI clock frequency is set to 3.125MHz.
Figure 2. The Fresno firmware flowchart for Nexys 3 platform.
The firmware accepts commands, writes status, and is capable of downloading blocks of sampled data to a
standard terminal program via a virtual COM port. The complete source code is provided to speed up customer
development. Code documentation can be found in the corresponding firmware platform files.
Detailed Description of Firmware for ZedBoard Platform
The Fresno firmware design is also developed and tested for the ZedBoard kit and targets an ARM
®
Cortex
®
-
A9 processor placed inside a Xilinx Zynq system-on-chip (SoC). An AXI MAX11100 custom IP core is created
for this reference design to optimize the sampling rate and the SPI timing stability.
The firmware is a working example of how to interface to the hardware, collect samples, and save them to
memory. The simple process flow is shown in Figure 3. The firmware is written in C using the Xilinx SDK tool,
Page 4 of 11
which is based on the Eclipse open source standard. Custom Fresno-specific design functions were created
utilizing the AXI MAX11100 custom IP core. The SPI clock frequency is set to 4.54MHz when a 189.4ksps
sampling rate is selected. The SPI clock frequency is set to 2.5MHz for all other sampling rates.
Figure 3. The Fresno firmware flowchart for ZedBoard platform.
The firmware accepts commands, writes statuses, and is capable of downloading blocks of sampled data to a
standard terminal program via a virtual COM port. The complete source code is provided to speed up customer
development. Code documentation can be found with the corresponding firmware platform files.
Quick Start
Required equipment:
Windows
®
PC with two USB ports
Fresno (MAXREFDES11#) Board
Fresno-supported Platform (i.e., Nexys 3 development kit or ZedBoard kit)
Industrial sensor or signal source
Download, read, and carefully follow each step in the appropriate Fresno Quick Start Guide:
Fresno (MAXREFDES11#) Nexys 3 Quick Start Guide
Page 5 of 11
下载中心专版
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
