Note: In order to connect the programmer easily and quickly, please connect the hardware after installing
the software.
Copyrights
Software
2003-2008 XELTEK
User’s Guide Copyright
2003-2008 XELTEK
Copyrights
©
2003-2008 XELTEK
The distribution and sales of the product are intended for use by the original purchaser under the terms of
the License Agreement. This document may not, in whole or part, be copied, photocopied, reproduced,
translated or reduced to any electronic medium of machine-readable form without prior consent in
writing from XELTEK.
The information in this document is subject to change without notice.
SUPERPRO
®
is the trademark of XELTEK.
1. General Description
1.1 INTRODUCTION
1.1.1 What is Superpro?
The SUPERPRO is a series of cost-effective, reliable, and high-speed universal programmers. They are
designed to communicate through a USB or parallel port (model dependent) and to operate with most
IBM-compatible desktop computers and notebook computers. Their menu-driven software interface
makes them easy to operate.
Programming hardware includes the following items:
·A programming module (including a 40 or 48 pin ZIF)
·An AC adapter w/ dual range switching power supply (model dependent)
·A USB or parallel connecting cable
·Optional socket adapters to accommodate PLCC, TSOP, SOIC, SOP, QFP, TSSOP and BGA package
types are available.
·Software (CD)
Software includes the following features:
·Supports Windows 95/NT/2000/XP
·Programming support for a large number of devices (1500-11000) including PROMs,
PLDs and MCU from more than 100 manufacturers (model dependent).
E/EPROMs,
·Support formats in Binary, Intel (linear & segmented) Hex, Motorola S, Tektronix (linear & segmented),
Jed, POF etc.
·Device insertion test (48 pins or less) to detect defective chip, improper inserted device and loose
contacted pin (model dependent)
·Integrated full screen buffer editors with commands for fill, copy, move, swap, etc.
·Auto-generation of electronic serial numbers (model dependent)
·Project and selecting history
1.1.2 Manual Organization
This booklet consists of five main chapters:
Chapter 1: Provides an introduction to the SUPERPRO series, including system requirements.
Chapter 2: Provides system set up information, such as set-up of the hardware and software as well as
solutions for communication error if encountered.
Chapter 3: Provides pre-programming guidance and device selection, loading and reading data.
Chapter 4: Provides explanation for each software command and its functions.
Chapter 5: Provides guidance for trouble shooting and error messages.
1.1.3 Manual convention
The following conventions are used in this manual:
·The names of all keyboard keys are enclosed in angle brackets,
For example the Enter (or Return) key is shown as <Enter>
the Page Up key is shown as <PgUp>
·The cursor keys are shown as follows:
Left arrow key = <Left arrow>
Right arrow key = <Right arrow>
Up arrow key = <Up arrow>
Down arrow key = <Down arrow>
·Unless stated otherwise, keystrokes are not case-sensitive. e.g.: Both ‘A’ and ‘a’ are acceptable.
1.1.4 System Requirements
The minimum requirements are as follows:
·A Personal Computer, IBM or compatible, desktop or laptop, one USB port (USB 1.0) or one
parallel port (model dependent)
·Windows 98/NT/2000/XP operating system
·CD-ROM driver
·Hard disk of at least 20MB of spare capacity
1.1.5 Programmer Package
Standard package contains the following:
·A programmer module
·A parallel or USB connecting cable (model dependent)
·An AC adapter or a dual range switching power supply (model dependent)
·The installation software CD
·User’s Guide
·Registration card
2. System Setup
Parallel-based programmer’s software installation is straightforward and self-explanatory. If it’s your
first time to use the USB-based programmer of XELTEK, this chapter will help you to properly install
the software and connect the hardware. USB devices are PnP devices. At first installation, Windows will
start with “new hardware wizard” to scan all available INF files, and find out the appropriate driver. In
order to avoid unwanted complication during installation of USB device, we strongly suggest that you
install the software first. The setup program will handle the needed INF files and drivers automatically.
2.1 Software Setup
The content in 2.1.1, 2.1.2, 2.1.3, and 2.1.5 is applicable for both USB-based and Parallel-based
programmers.
2.1.1 Setup from CD-ROM
Insert the CD into a CD-ROM driver and the setup program will start automatically, if not, please run
SETUP.EXE in the root path.
Caution: Each model has its own software, please do not mismatch.
2.1.2 Download software from the Internet
You can download the specific software for a certain model at Xeltek website. It is usually a
self-extracting file. You only need to run this file to setup the software.
2.1.3 Setup Process
The setup procedure goes step by step, you can change the default settings as you needed during setup
process.
First, setup wizard, please read the text carefully.
Click “next” button
Second, select destination fold
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
