IE-iMcV-T1/E1/J1-LineTerm
SFP and 1x9
Operation Manual
Above illustration is representative; different models available
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class A
limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe A
prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Warranty
IMC Networks warrants to the original end-user purchaser that this product, EXCLUSIVE OF SOFTWARE, shall be free
from defects in materials and workmanship under normal and proper use in accordance with IMC Networks' instructions
and directions for a period of six (6) years after the original date of purchase. This warranty is subject to the limitations set
forth below.
At its option, IMC Networks will repair or replace at no charge the product which proves to be defective within such
warranty period. This limited warranty shall not apply if the IMC Networks product has been damaged by unreasonable
use, accident, negligence, service or modification by anyone other than an authorized IMC Networks Service Technician
or by any other causes unrelated to defective materials or workmanship. Any replaced or repaired products or parts carry
a ninety (90) day warranty or the remainder of the initial warranty period, whichever is longer.
To receive in-warranty service, the defective product must be received at IMC Networks no later than the end of the
warranty period. The product must be accompanied by proof of purchase, satisfactory to IMC Networks, denoting
product serial number and purchase date, a written description of the defect and a Return Merchandise Authorization
(RMA) number issued by IMC Networks. No products will be accepted by IMC Networks which do not have an RMA
number. For an RMA number, contact IMC Networks at PHONE: (800) 624-1070 (in the U.S. and Canada) or (949) 465-
3000 or FAX: (949) 465-3020. The end-user shall return the defective product to IMC Networks, freight, customs and
handling charges prepaid. End-user agrees to accept all liability for loss of or damages to the returned product during
shipment. IMC Networks shall repair or replace the returned product, at its option, and return the repaired or new
product to the end-user, freight prepaid, via method to be determined by IMC Networks. IMC Networks shall not be
liable for any costs of procurement of substitute goods, loss of profits, or any incidental, consequential, and/or special
damages of any kind resulting from a breach of any applicable express or implied warranty, breach of any obligation
arising from breach of warranty, or otherwise with respect to the manufacture and sale of any IMC Networks product,
whether or not IMC Networks has been advised of the possibility of such loss or damage.
EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, IMC NETWORKS MAKES NO OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS IMC NETWORKS PRODUCT, INCLUDING WITHOUT
LIMITATION ANY SOFTWARE ASSOCIATED OR INCLUDED. IMC NETWORKS SHALL DISREGARD AND NOT BE
BOUND BY ANY REPRESENTATIONS OR WARRANTIES MADE BY ANY OTHER PERSON, INCLUDING EMPLOYEES,
DISTRIBUTORS, RESELLERS OR DEALERS OF IMC NETWORKS, WHICH ARE INCONSISTENT WITH THE WARRANTY
SET FORTH ABOVE. ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY LIMITED TO THE DURATION OF THE EXPRESS WARRANTY STATED ABOVE.
Every reasonable effort has been made to ensure that IMC Networks product manuals and promotional materials
accurately describe IMC Networks product specifications and capabilities at the time of publication. However, because of
ongoing improvements and updating of IMC Networks products, IMC Networks cannot guarantee the accuracy of printed
materials after the date of publication and disclaims liability for changes, errors or omissions.
ii
Table of Contents
FCC Radio Frequency Interference Statement ....................................................ii
Warranty............................................................................................................ii
About the IE-iMcV-T1/E1/J1-LineTerm................................................................1
Installing an iMcV-Module .................................................................................2
Crossover/Straight-Through Connection..............................................................2
Configuration .....................................................................................................2
Prerequisites ......................................................................................................2
Managed Modules .............................................................................................3
Configuration Control ........................................................................................4
Unmanaged Modules.........................................................................................5
DIP Switches......................................................................................................6
DIP Switch Settings (S2, S3)................................................................................7
Features .............................................................................................................9
LED Operation.................................................................................................13
Loopback Testing .............................................................................................14
Pseudorandom Bit Sequence (PRBS) Testing ....................................................15
Installation Troubleshooting .............................................................................15
Specifications ...................................................................................................17
IMC Networks Technical Support.....................................................................17
Fiber Optic Cleaning Guidelines.......................................................................18
Electrostatic Discharge Precautions...................................................................19
Certifications....................................................................................................20
iii
About the IE-iMcV-T1/E1/J1-LineTerm, TP/SFP
NOTE
Unless noted otherwise, any reference is applicable for both the 1x9 and SFP version of
the
IE-iMcV-T1/E1/J1-LineTerm
in this manual.
IE-iMcV-T1/E1/J1-LineTerm, TP/SFP is an SNMP-Manageable module that converts
standard TDM-based copper transports (T1, E1, J1) to a single-mode or multi-mode
fiber signal. It performs a standard “Line Termination” function as defined in GR-
820-CORE. This function transmits an Alarm Indication Signal (AIS) on the line
whenever the received signal is lost. Line faults can easily be isolated to one line
section and do not propagate over multiple-line sections as they do with normal line
repeaters.
Each module includes one RJ-48 connector, one pair of ST or SC fiber optic
connectors or an SFP port, which can support any fiber type at 155Mbps; dual strand
available in LC connectors, and Single Strand Fiber SFPs available in SC connectors.
IE-iMcV-T1/E1/J1-LineTerm, TP/SFP modules install into any modular, SNMP
manageable iMediaChassis, as well as the MediaChassis series, which is unmanaged.
The IE-iMcV-T1/E1/J1-LineTerm, TP/SFP offers an extended temperature range of
-40°C to +85°C; when installed in an IE-MediaChassis/1 or 2, available in AC and
DC, the module can be installed in challenging heat or cold-related environments.
An IE-iMcV-T1/E1/J1-LineTerm, TP/SFP with SFP Module with Configuration Control,
configured as a Host, allows an SNMP Management Module in a managed chassis to
manage the Remote. All settings are enabled and enforced through the SNMP. The
Host keeps a copy of the Remote’s configuration settings. Each module offers the
feature Configuration Control; please refer to the appropriate section.
When the Host unit is not in a managed chassis, the Host configures the Remote. This
ensures that the Remote’s configuration will not revert to its DIP Switch settings and
potentially disrupt traffic. However, if the user changes the DIP Switch settings on the
Remote, the new configuration of the Remote will be enabled.
When SNMP management is installed at the Host, the following functions at the
Remote are controlled from the Host unit:
•
•
•
•
Loopback
Line Code
Transmit Data Source
Fault Loopback
The IE-iMcV-T1/E1/J1-LineTerm, TP/SFP with SFP Host unit can also display the
DDMI information from the Remote LineTerm module. Please download the latest
SNMP Management Module firmware and iVIew² software to ensure the full support
and functionality of the modules.
1
NOTE
IE-iMcV-T1/E1/J1-LineTerm, TP/SFP
with SFP Module can be installed in an iMediaChassis
and MediaChassis series.
Installing an iMcV-Module
iMcV-Modules install in IMC Networks’ SNMP manageable iMediaChassis series or in
any MediaChassis/IE-MediaChassis series.
To install an iMcV-Module:
1.
2.
3.
4.
Remove the blank bracket covering the slot where the module is to be installed
by removing the screws on the outside edges of the bracket.
Slide the iMcV-Module into the chassis, via the cardguides, until the module is
seated securely in the connector.
Secure the module to the chassis by tightening the captive screw.
Save any “blanks” removed during installation for future use if the configuration
requirements change.
NOTE
All modules are hot-swappable
Crossover/Straight-Through Connection
IE-iMcV-T1/E1/J1-LineTerm, TP/SFP comes with an RJ-48 UTP connector that features
a push-button switch, located next to the port, for selecting a crossover connection,
push-button IN. A straight-through connection is selected when the push-button is
OUT. When unsure what type of connection is needed, set the push button to the
position that turns the LOS LED off.
Configuration
Proper configuration of the IE-iMcV-T1/E1/J1-LineTerm, TP/SFP is required for
maximum performance and reliability. The following sections describe the
prerequisites and the configurations available for both managed and unmanaged
modules.
Prerequisites
The IE-iMcV-T1/E1/J1-LineTerm, TP/SFP conforms to any T1/E1/J1-based
environment. Ensure all of the relevant information about the expected installation
environment is available before configuring the module. This information includes:
•
Line Type T1 or E1
•
Line Coding used on T1: either AMI or B8ZS
•
Distance of the copper run for DSX1 lines (655 feet MAX)
2
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
