TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-095
REV.
USB PRODUCT SPECIFICATION
1
OF
17
AUTHORIZED BY
DATE
K
09/11/2014
JOHN HAN
1.0 OBJECTIVE
THIS SPECIFICATION DEFINES THE PERFORMANCE, TEST, QUALITY AND
RELIABILITY REQUIREMENTS OF THE USB (UNIVERSAL SERIAL BUS) INCLUDING
THE FOLLOWING:
SERIES “A” RIGHT ANGLE SINGLE DECK
SERIES “A” RIGHT ANGLE SINGLE DECK WITH SENSOR PIN
SERIES “A” RIGHT ANGLE DOUBLE DECK
SERIES “A” SMT SINGLE DECK
SERIES “A” PLUG
2.0 SCOPE
THIS SPECIFICATION IS APPLICABLE TO THE TERMINATION CHARACTERISTICS
OF THE USB FAMILY OF PRODUCTS WHICH PROVIDES INTERCONNECTION OF
COMPUTER PERIPHERALS
3.0 GENERAL:
THIS DOCUMENT IS COMPOSED OF THE FOLLOWING SECTIONS:
PARAGRAPH
1.
2.
3.
4.
5.
5.1
5.2
5.3
5.4
5.5
6.
7.
8.
9.
9.1
TITLE
OBJECTIVE
SCOPE
GENERAL
APPLICABLE DOCUMENTS
REQUIREMENTS
QUALIFICATION
PRODUCT EXAMINATION
MATERIAL
FINISH
DESIGN AND CONSTRUCTION
ELECTRICAL CHARACTERISTICS
MECHANICAL CHARACTERISTICS
ENVIRONMENTAL CHARACTERISTICS
QUALITY ASSURANCE PROVISIONS
EQUIPMENT CALIBRATION
NOTE: THIS DOCUMENT IS THE PROPERTY OF AND EMBODIES PROPRIETARY INFORMATION OF THE FCI ELECTRONICS COMPANY. NO PART OF THE INFORMATION
SHOWN ON THIS DOCUMENT MAY BE USED IN ANY WAY WITHOUT THE WRITTEN CONSENT OF FCI ELECTRONICS.
E-3005
04/14/99
GES-01-001
PDS: Rev :K
STATUS:Released
Printed: Sep 19, 2014
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-095
REV.
USB PRODUCT SPECIFICATION
2
OF
17
AUTHORIZED BY
DATE
K
09/11/2014
JOHN HAN
9.2
9.3
9.4
9.5
9.6
INSPECTION CONDITIONS
SAMPLES QUANTITY AND DESCRIPTION
ACCEPTANCE
QUALIFICATION TESTING
RE-QUALIFICATION TESTING
CONTACT RESISTANCE MEASUREMENT POINTS TYPICAL
VIBRATIONS AND PHYSICAL SHOCK MOUNTING FIXTURE
QUALIFICATION TESTING AND SEQUENCE MATRIX
FIGURE 1
FIGURE 2
TABLE
1
4.0 APPLICABLE DOCUMENTS
4.1
SPECIFICATIONS:
4.1.1 ENGINEERING DRAWINGS
SERIES “A”
87520
87583
72313
72367
72507
73725
SINGLE DECK RECEPTACLES:
THROUGH HOLE
SURFACE MOUNT W/THROUGH HOLE CLAWS
SENSOR PIN THROUGH HOLE
SENSOR PIN SURFACE MOUNT W/THROUGH HOLE CLAWS
SENSOR PIN SURFACE MOUNT W/SURFACE MOUNT TABS
SIDE MOUNT
74612/56434/52369 SMT SPECIAL SHIELD
74552
74626
74510
61819
74056
52469
THROUGH HOLE REVERSED
SURFACE MOUNT REVERSED
SMT WITH TOP SCREW MOUNT
STAND SOLDED TAIL THROUGH HOLE WITH TOP SCREW MOUNT
SHORT SOLDED TAIL THROUGH HOLE WITH TOP SCREW MOUNT
SIDE MOUNT SHORT BODY
52319/57422/57423,
54006/54026
SERIES “A”
72309
SERIES”A” PLUG
74033
74032
FULLY RATED
SUB-CHANNEL
SIDE MOUNT SHORT BODY
DOUBLE DECK RECEPTACLES:
THROUGH HOLE
NOTE: THIS DOCUMENT IS THE PROPERTY OF AND EMBODIES PROPRIETARY INFORMATION OF THE FCI ELECTRONICS COMPANY. NO PART OF THE INFORMATION
SHOWN ON THIS DOCUMENT MAY BE USED IN ANY WAY WITHOUT THE WRITTEN CONSENT OF FCI ELECTRONICS.
E-3005
04/14/99
GES-01-001
PDS: Rev :K
STATUS:Released
Printed: Sep 19, 2014
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-095
REV.
USB PRODUCT SPECIFICATION
3
OF
17
AUTHORIZED BY
DATE
K
09/11/2014
JOHN HAN
4.2
MILITARY STANDARDS
4.2.1.
4.2.2.
4.2.3.
MIL-STD-202F:
MIL-STD-1344A:
MIL-C-45662:
TEST METHODS FOR ELECTRONIC COMPONENT PARTS
TEST METHODS FOR ELECTRICAL CONNECTORS
EQUIPMENT CALIBRATION
4.3
FEDERAL SPECIFICATIONS
4.3.1.
4.3.2.
4.3.3.
QQ-N-290:
QQ-B-750:
QQ-S-571
NICKEL PLATING (ELECTRODEPOSITED)
PHOSPHOR BRONZE ALLOY STRIP
SOLDER
4.4 OTHER STANDARDS AND SPECIFICATIONS
4.4.1
4.4.2
4.4.3
4.4.4
UL94:
ASTM B-103:
ISO 9000:
EIA 364:
FLAMMABILITY
PHOSPHOR BRONZE
ELECTRICAL CONNECTOR/SOCKET TEST
PROCEDURES INCLUDING ENVIRONMENTAL
CLASSIFICATIONS
4.4.5
ASTM-D-4565:
PHYSICAL AND ENVIRONMENTAL PERFORMANCE
PROPERTIES OF INSULATION AND JACKET FOR
TELECOMMUNICATIONS WIRE AND CABLE, TEST
STANDARD METHOD
4.4.6 ASTM-D-4566:
ELECTRICAL PERFORMANCE PROPERTIES OF
ISULATION AND JECKET FOR TELECOMMUNICATION
WIRE AND CABLE
TEST STANDARD METHOD
4.4.7 USB UNIVERSAL SERIAL BUS SPECIFICATION
4.5 FCI SPECIFICATIONS
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
4.5.6
4.5.7
4.5.8
BUS-03-114:
BUS-03-404:
BUS-03-405:
BUS-03-601:
BUS-16-016:
BUS-16-074:
BUS-19-002:
BUS-19-020:
CAPACITANCE MEASUREMENT
NORMAL FORCE MEASUREMENT
INSERTION/WITHDRAWAL FORCE MEASUREMENT
CURRENT RATING/30 DEGREES TEMPERATURE RISE
PHOSPHOR BRONZE STRIP
PCT, 30% GLASS
SOLDERABILITY
POROSITY
NOTE: THIS DOCUMENT IS THE PROPERTY OF AND EMBODIES PROPRIETARY INFORMATION OF THE FCI ELECTRONICS COMPANY. NO PART OF THE INFORMATION
SHOWN ON THIS DOCUMENT MAY BE USED IN ANY WAY WITHOUT THE WRITTEN CONSENT OF FCI ELECTRONICS.
E-3005
04/14/99
GES-01-001
PDS: Rev :K
STATUS:Released
Printed: Sep 19, 2014
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-095
REV.
USB PRODUCT SPECIFICATION
4
OF
17
AUTHORIZED BY
DATE
K
09/11/2014
JOHN HAN
4.5.9
4.6.0
4.6.1
BUS-19-040:
BUS-19-002:
BUS-19-122:
PLATING ADHESION
SURFACE MOUNT SOLDER JOINT RELIABILITY
SOLDER JOINT RELIABILITY TEST PROCEDURE FOR
SURFACE MOUNT CONNECTORS
5.0 REQUIREMENTS
5.1 QUALIFICATION
CONNECTORS FURNISHED UNDER THIS SPECIFICATION SHALL BE CAPABLE
OF MEETING THE QUALIFICATION TEST REQUIREMENTS SPECIFIED HEREIN.
5.2 PRODUCT EXAMINATION
PRODUCT WILL BE EXAMINED PER EIA-364-18 VERIFYING VISUALLY
PARAGRAPHS 5.3, 5.4 AND 5.5. DIMENSIONAL EXAMINATION IS NOT REQUIRED.
5.3 MATERIAL
MATERIAL FOR EACH PART SHALL BE SPECIFIED HEREIN, OR EQUIVALENT,
SUBSTITUTE MATERIAL SHALL MEET THE PERFORMANCE REQUIREMENTS
OF THIS SPECIFICATION.
5.3.1 RECEPTACLE TERMINAL; THE BASE MATERIAL SHALL BE PHOSPHOR-
BRONZE STRIP
5.3.2 RECEPTACLE INSULATOR HOUSINGS; CONNECTORS SHALL BE MOLDED
OF PLASTIC THAT IS RATED UL94-V-0 OR BETTER IN ACCORDANCE.
WITH UL-94.
5.3.3 RECEPTACLE SHELL; THE BASE MATERIAL SHALL BE PHOSPHOR-
BRONZE STRIP.
5.3.4 INSULATOR HOUSINGS AND COVERS OF LEAD FREE PART
- THE INSULATOR
HOUSINGS AND COVERS OF LEAD FREE PART WILL WITHSTAND EXPOSURE TO
260℃ PEAK TEMPERATURE FOR 40 SECONDS IN A CONVECTION, INFRA-RED OR
VAPOUR PHASE REFLOW OVEN.
NOTE: THIS DOCUMENT IS THE PROPERTY OF AND EMBODIES PROPRIETARY INFORMATION OF THE FCI ELECTRONICS COMPANY. NO PART OF THE INFORMATION
SHOWN ON THIS DOCUMENT MAY BE USED IN ANY WAY WITHOUT THE WRITTEN CONSENT OF FCI ELECTRONICS.
E-3005
04/14/99
GES-01-001
PDS: Rev :K
STATUS:Released
Printed: Sep 19, 2014
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-095
REV.
USB PRODUCT SPECIFICATION
5
OF
17
AUTHORIZED BY
DATE
K
09/11/2014
JOHN HAN
5.3.5 LEAD FREE PART – ALL LEAD FREE PARTS ARE COMPATIBLE WITH ROHS.
5.4 FINISH
5.4.1 RECEPTACLE TERMINAL SHALL BE PLATED IN THE CONTACT AREA
WITH 0.76um (30u”INCHES) PALLADIUM NICKEL WITH GOLD FLASH MINIMUM OR 0.76um
(30u”INCHES) GOLD OVER 1,27um (50u” INCHES) MINIMUM NICKEL. THE RECEPTACLE TERMINAL
SOLDER TAIL SECTIONS SHALL BE PLATED WITH 2,54um (100u”INCHES) 90/10 TIN-LEAD MINIMUM
or 2,54um (100u” INCHES) MINIMUM MATTED TIN FOR LEAD FREE PART OVER 1,27um
(50u”INCHES) MINIMUM NICKEL. THE TERMINAL AREAS OUTSIDE OF THE CONTACT AREAS AND THE
SOLDER TAIL AREAS SHALL BE PLATED WITH 1,27um (50u”INCHES) NICKEL MINIMUM.
5.4.2 OUTSIDE SEHLL OF THE RECEPTACLE SHALL BE PLATED WITH 2.54um
(100u”INCHES) 90/10 TIN-LEAD MINIMUM OR 2.54um (100u”INCHES) MINIMUM
PURE TIN OVER 1,27um (50u”INCHES) MINIMUM NICKEL UNDERPLATE.
5.4.3 Lead free plating - ALL PLATING BATH FOR COMPONENTS OF LEAD FREE
PART ARE QUALIFIED BY FCI. FCI QUALIFICATION INCLUDES SOLDERABILITY,
WHISKERING, SOLDER JOINT RELIABILITY AND TARNISHING EFFECTS.
5.5 DESIGN AND CONSTRUCTION
5.5.1.SINGLE DECK: THE RECEPTACLE CONNECTOR SHALL BE A MULTIPLE PIECE
ASSEMBLY HAVING A SINGLE ROWS OF CONTACTS.SPACE ON DISSIMILAR
CENTER LINE (THE TWO INNER CONTACTS ARE SPACED 2.0mm APART AND THE
TERMINALS ADJACENT TO THESE TERMINALS ARE SPECED 2.5mm AWAY) IN THE
INTERFACE AREA. EACH TERMINAL TRANSITION WILL BE A 90 DEGREES BEND
TO ALLOW FOR TERMINATION TO THE PC BOARD BY EITHER A THROUGH HOLE
LEG OR A SMT LEG. THE OUTSIDE SHELL HAS FOUR RESILIENT CONTACT ARMS
(TWO ON TOP AND TOW ON THE BOTTOM) THAT ACT AS ESD GROUNDING AS
WELL AS CABLE PLUG RETENTION FEATURES. TWO ADDITIONAL ARMS ON THE
SIDE OF THE SHELL ASSURE THAT THERE IS CONSTANT CONTACT BETWEEN THE
SHELL AND THE SHELL OF THE CABLE ASSEMBLY PLUG WHILE THE CONNECTORS
NOTE: THIS DOCUMENT IS THE PROPERTY OF AND EMBODIES PROPRIETARY INFORMATION OF THE FCI ELECTRONICS COMPANY. NO PART OF THE INFORMATION
SHOWN ON THIS DOCUMENT MAY BE USED IN ANY WAY WITHOUT THE WRITTEN CONSENT OF FCI ELECTRONICS.
E-3005
04/14/99
GES-01-001
PDS: Rev :K
STATUS:Released
Printed: Sep 19, 2014
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
