DOCUMENT : RT440000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
1
OF
10
RS4NXXXXJX Resistor Network
1. Scope
This specification applies to 1.0mm x 2.0mm (0804) size resistor network
(8P4R) with 4 isolated resistor for use in electronic equipment.
2. Type Designation
RS4N – XXXX – J – X
(1)
(2)
(3)
(4)
Where (1) Series No :
0804 Size & 8 Pin 4 Resistor
(2) Nominal resistance value :
For example –-
56R0 = 56
1001 = 1k
(3) Resistance tolerance :
J =
5.0%
(4) Outline type :
1 = Rectangular corner
2 = Flat
3. Electrical Specifications
Power Rating*
Resistance Values
Resistance Tolerance
T.C.R.
(Temperature Coefficient of Resistance)
Operating Temperature Range
Maximum Operating Voltage**
63mW/each element
10 to 1M in E-24 series
5.0%
250ppm/
-55 to 125
25V
DOCUMENT : RT440000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
2
OF
10
Note: *Package Power Temperature Derating Curve
Note: **Resistors shall have a rated DC or AC(rms) continuous operating voltage
corresponding to the power rating, as calculated from the following formula
Where V : Rated voltage (V)
V=
PxR
P : Rated power (W)
R : Nominal resistance ()
If the voltage so obtained exceeds the maximum operating voltage, this
maximum voltage shall be the rated voltage.
4. Outline dimensions and marking
4-1 Rectangular corner
Three Digits:
102
4-2 Flat type
560 = 56
102 = 1k
102
2.0
0.1
P
0.5 typical
W 1.0
0.1
C
0.22
0.1
A
0.35
0.1
D
0.35 max.
T
0.4
0.1
Unit : mm
L
DOCUMENT : RT440000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
3
OF
10
5. Schematics
8
5
R1
R2
R3
R4
1
R1=R2=R3=R4
6. Life test
6-1 Electrical
Item
Short Time
Overload
4
Specification and Requirement
Test Method
(1) Applied voltage:
R:
(2.0%+ 0.1)
Without damage by flashover,
2.5 x rated voltage or
spark, arcing, burning or
2 x maximum operating
breakdown
voltage which ever is less
(2)Test time : 5 seconds
Over 100 M on Overcoat
layer face up
Over 1,000 M on Substrate
side face up
R:
(1.0%+ 0.05)
Without damage by flashover,
spark, arcing, burning or
breakdown
(1)Setup as figure 2
(2)Test voltage: 100 V DC
(3)Test time:
60 + 10 / -0 seconds
(1)Setup as figure 2
(2)Test voltage: 100 V AC(rms)
(3)Test time:
60 +10 / -0 seconds
Insulation
Resistance
Voltage Proof
DOCUMENT : RT440000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
4
OF
10
6-2 Mechanical
Item
Solderability
Specification and Requirement
The surface of terminal
immersed shall be minimum
of 95% covered with a new
coating of solder
Test Method
Resistance to
Solder Heat
Vibration
Shock
Solder bath:
After immersing in flux,
dip in 235
5 molten
solder bath for 2
0.5
seconds
(1) Pre-heat: 100~110 for
R:
(1.0%+ 0.05)
30 seconds
Without distinct deformation in
(2) Immersed at solder bath
appearance
of 260
5 for
10
1 seconds
(3) Measuring resistance
1 hour after test
(1) Vibration frequency:
R:
(0.5%+ 0.05)
Without mechanical damage
( 10Hz to 55Hz to10Hz )
such as break
in 60 seconds as a period
(2) Vibration time:
period cycled for 2 hours
in each of 3 mutual
perpendicular directions
(3) Amplitude: 1.5mm
(1) Peak value: 490N
R:
(0.25%+ 0.05)
Without mechanical damage (2) Duration of pulse: 11ms
(3) 3 times in each positive
such as break
and negative direction of
3 mutual perpendicular
directions
DOCUMENT : RT440000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
5
OF
10
6-2 Mechanical
Item
Bending Test
Specification and Requirement
Test Method
Solvent
Resistance
Bending value: 3 mm for
R:
(1.0%+ 0.05)
Without mechanical damage 30
1 seconds
such as break
Marking should be legible
(1)Solvent:
Without mechanical and
Trichloroethane
distinct damage in appearance
or Isopropyl alcohol
(2)Immersed in solvent at
room temperature for
90 seconds
6-3 Endurance
Item
Specification and Requirement
Test Method
(1)Repeat 5 cycle as
follow:
(-55
3,30minutes)
→(Room
temperature,
2~3 minutes)
→(+125
2,30minutes)
→(Room
temperature,
2~3 minutes)
(2)Measuring resistance
1 hour after test
(1) Environment condition:
40
2,90~95% RH
(2)Applied Voltage:
rated voltage
(3)Test period: (1.5 hour
ON)→(0.5 hour OFF)
cycled for total 1,000
+ 48 / - 0 hours
(4)Measuring resistance
1 hour after test
Rapid change of
R:
(1.0%+ 0.05)
Temperature
Without distinct damage in
appearance
Moisture with
Load
R:
(3.0%+ 0.1)
Without distinct damage in
appearance
Marking should be legible
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
