Form No.: QF-1274
Edition: 2
SPECIFICATION FOR APPROVAL
Customer：
Customer P/N:
Drawing No：
Quantity：
Chilisin P/N：
0
Pcs.
Date：
ACTW Series
2021/7/7
Automotive Grade Resistor
Halogen Free
RoHS Compliant
REACH Compliant
Lead Free Solders
AEC-Q200
奇力新電子股½有限公司
Chilisin Electronics Corp
No. 29, Alley 301, Tehhsin Rd., Hukou,Hsinchu
303, Taiwan
TEL：+886-3- 599-2646
FAX：+886-3- 599-9176
E-mail：sales@chilisin.com
http：//www.chilisin.com
東莞奇力新電子(東莞廠)有限公司
Chilisin Electronics (Dongguan) Co., Ltd.
No. 78, Puxing Rd., Yuliangwei Administration Area,
Qingxi Town, Dongguan City, Guangdong,China
TEL：+86-769-8773-0251~3
FAX： +86-769-8773-0232
E-mail：cect@chilisin.com
奇力新電子(越南廠)有限公司
Chilisin Electronics (Vietnam) Limited
No 143 - 145, Road No 10, VSIP Hai Phong,
Lap Le Commune, Thuy Nguyen Dist,
Haiphong City, Vietnam
奇力新電子(湖南廠)有限公司
HuNan Chilisin Electronics Technology Co., Ltd
No. 8, Shaziao Liangshuijing Town, Yuanling County,
Huaihua City, Hunan Province 419601, China
Tel：86-745-867-5882
Drawn by
Checked by
Approved by
Desmond.Wu
Cf.Hsieh
Wl.Liu
ACTW Series Specification
1 Scope:
1-1 This specification is applicable to lead free and halogen free of RoHS directive for
ACTW series wide terminal thick film chip resistors
1-2 This product is for automotive electronic application
1-3 AEC-Q200 qualified , grade 0.
2 Part Numbering:
A
C
Series
ACTW:
Wide Terminal Thick Film Chip
Resistors for Automotive
Grade
T
W
0
0
0 6 1 2
Dimension
(inch)
0508
0612
1218
1020
1225
-
1 0 0 2
Resistance Value
J Tol: (3 digit + X)
Ex. 10Ω = 100
4.7Ω = 4R7
Jumper = 000
F/D/B Tol: (4 digit)
Ex. 10.2 Ω = 10R2
10KΩ = 1002
F
Tolerance
D=± 0.5%
F=± 1%
J=± 5%
TP
Taping Code
TP ( 5,000 pcs/reel) : 0612, 0508
TE (4,000 pcs/reel): 1218, 1020, 1225
Internal
Code
3 SPECIFICATIONS:
≧1Ω&0Ω
3.1 Resistance Range:＜1Ω
JUMPER
(0Ω)
Rated Power
J
(±5%)
F
(±1%)
Type
Rated
Power
at
70℃
Max.
Working
Voltage
Max.
Overload
Voltage
Resistance Range
T.C.R
(ppm/℃)
D(±0.5%)、F(±1%)
E-24、E-96
J(±5%)
E-24
JUMPER
(0Ω)
Resistance
Value
J
(±5%)
F
(±1%)
0508
0612
1218
1020
1225
1/3W
3/4W
150V
200V
200V
400V
±200
±100
±200
±100
±200
±100
±200
±100
±200
±100
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
1Ω≦R＜10Ω
10Ω≦R≦1MΩ
2.5A
3A
4.0A
5A
50mΩ 20mΩ
MAX. MAX
50mΩ 20mΩ
MAX.
MAX.
1W
250V
500V
2A
7A
50mΩ 20mΩ
MAX.
MAX.
1W
200V
400V
2A
7A
50mΩ 20mΩ
MAX.
MAX.
2W
200
400
2A
8.5A
50mΩ 20mΩ
MAX.
MAX.
Operating Temperature Range
-55℃ ~ +155℃
ACTW Series Specification
3.2 Power Derating Curve:
Operating Temperature Range：- 55½155
℃
For resistors operated in ambient temperatures above 70℃, power rating shall be derated in
accordance with figure below。
3.3 Voltage Rating:
3.3.1 Resistance Range:≧1Ω
Rated Voltage: DC voltage or AC voltage (rms) based on the rated power.
The voltage can be calculated by the following formula. If the calculated value
exceeds the Max.voltage specified in the Table 3, the Max. voltage rating is set as the
voltage rating.
E
½
R×P
E= Rated voltage (v)
P= Power rating (w)
R= Nominal resistance(Ω)
ACTW Series Specification
6 Reliability Test:
No
Item
Exposure (Storage)
Conditions
Put the specimens in the chamber with temperature of
155±3℃ for 1000 hours. Then take them out to stabilize
in room temperature for 24±4hr or more, and measure of
its resistance variance rate.
Experiment evidence: AEC-Q200
Specifications
Resistors
0.5%、1%:△R=±1.0%
5%:△R=±2.0%
Jumper
Refer to
item 3.
general
specifications
1-1-1
High Temperature
1-1-2
Temperature
Cycling
Put the specimens in the High & low temperature test
chamber with temperature varies from -55℃ to 125℃
for 15 minutes and total 1000 cycles. Take them out to
stabilize in room temperature for 24±4hr or more,
and measure of its resistance variance rate.
Experiment evidence: AEC-Q200
0508/0612/1218/1020/1225 applied 2.5 times rated voltage
for 5 seconds ,RAW25 applied 2.5 times
rated voltage for 2 seconds, release the load for
about 30 minutes, then measure its resistance
variance rate. (Rated voltage refer to
item 3. general specifications)
0.5%、1%:△R=±1.0%
5%:△R=±2.0%
Refer to
item 3.
general
specifications
1-1-3
Short Time
Overload
0.5%、1%:△R=±1.0%
5%:△R=±2.0%
Refer to
item 3.
general
specifications
Refer to JIS-C5201-1 4.13
1-1-4
Biased Humidity
Solder the specimens on the test PCB and put them
into the constant temperature humidity chamber with
85±2℃ and 85±5%RH. Then apply the test voltage
that calculates based on the 10% of rated power
for 1000hrs. Then take them out to stabilize
in room temperature for 24±4hr or more,
and measure of its resistance variance rate.
Experiment evidence: AEC-Q200
1.R≧1Ω:
0.5%、1%:△ R=±2.0%
5%:△R=±3.0%
Refer to
item 3.
general
specifications
1-1-5
Operational
Life
Solder the specimens on the test PCB and put them
in the chamber with temperature of 125±3℃ and load
the rated power for 1000 hours. Then take them out to
stabilize in room temperature for 24±4hr or more,
and measure of its resistance variance rate.
Note: The input voltage shall refer to the power
derating curve (referring to page 2,No.3.2)
0.5%、1%:△R=± 2.0%
5%:△R=± 3.0%
Refer to item
3.general
specifications
1-1-6
Resistance to SolderingHeat
Experiment evidence: AEC-Q200
The specimens are fully immersed into the Pb-free
solder pot, then take them out to stabilize for 1 hour
or more and measure of its resistance variance rate.
Temp of solder pot：260±5℃.
Soldering duration：10±1sec.
Experiment evidence AEC-Q200
0.5%、1%:△R=± 2.0%
5%:△R=± 3.0%
Refer to item
3.general
specifications
电源技术
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
