DOCUMENT : RC000000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
1
OF 11
0805 Series Thin Film Chip Resistor
1. Scope
This specification applies to 1.25mm x 2.0mm (0805) size, fixed metal chip
resistors rectangular type for use in electronic equipment.
2. Type Designation
RR1220
X – XXX – X
(1)
(2)
(3)
(4)
Where (1) Series No.
(2) Tolerance of TCR :
P =
25ppm/
Q =
50ppm/
R =
100ppm/
(3) Nominal resistance value :
For example –-
Three digits of number (E-24 Series)
100 = 10
102 = 1k
Four digits of number (E-96 Series)
11R3 = 11.3
1131 =1.13k
(4) Resistance tolerance :
B =
0.1%
D =
0.5%
DOCUMENT : RC000000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
2
OF 11
3. Electrical Specifications
Power Rating*
1/10 W
Resistance Values
E-24 series,E-96 series
Resistance Tolerance
0.1%(B)
0.5%(D)
100100k 1091 100100k 110k1M
Resistance Range
T.C.R. (Temperature
Coefficient of
25ppm
50ppm
25ppm
100ppm
Resistance)
Operating Temperature
-55 to 125
Range
Max. Operating
100V
Voltage**
Note: *Package Power Temperature Derating Curve
Note: **Resistors shall have a rated DC or AC(rms) continuous operating voltage
corresponding to the power rating, as calculated from the following formula
Where V : Rated voltage (V)
V=
PxR
P : Rated power (W)
R : Nominal resistance ()
If the voltage so obtained exceeds the maximum operating voltage, this
maximum voltage shall be the rated voltage.
DOCUMENT : RC000000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
3
OF 11
4. Outline dimensions
Code
Letter
L
W
t
a
Dimension
2.00
1.25
0.40
0.40
0.2
0.2
0.1
0.2
Unit : mm
5. Marking
5-1 Marking in E-24 Series :
A rated resistance shall be marked on the protect coating with three
digits of number.
Example :
3.9k39 X 10
2
392
5-2 Marking in E-96 Series :
A Manufacturing date code shall be marked on the protect coating.
Example :
10.2102 X 10
-1
10R2
10.2k102 X 10
2
1022
DOCUMENT : RC000000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
4
OF 11
6. Life Tests
6-1 Electrical
Item
Short Time
Overload
Specification and Requirement Test Method
(1) Applied voltage:
R:
(0.5%+ 0.05)
Without damage by flashover,
2.5 x rated voltage or
spark, arcing, burning or
2 x maximum operating
breakdown
voltage which ever is less
(2)Test time : 5 seconds
Over 100 M on Overcoat
layer face up
Over 1,000 M on Substrate
side face up
R:
(0.5%+ 0.05)
Without damage by flashover,
spark, arcing, burning or
breakdown
(1)Setup as figure 2
(2)Test voltage: 100 V DC
(3)Test time:
60 + 10 / -0 seconds
(1)Setup as figure 2
(2)Test voltage: 100 V AC(rms)
(3)Test time: 60 +10 / -0
seconds
Insulation
Resistance
Voltage Proof
DOCUMENT : RC000000
CYNTEC CO., LTD.
REVISION
: B0
PAGE
:
5
OF 11
6-2 Mechanical
Item
Solderability
Specification and Requirement Test Method
The surface of terminal
Solder bath:
immersed shall be minimum of
After immersing in flux, dip
95% covered with a new
in 235
5 molten
coating of solder
solder bath for
2
0.5 seconds
(1) Pre-heat: 100~110 for
R:
(0.5%+ 0.05)
30 seconds
Without distinct deformation in
(2) Immersed at solder bath
appearance
of 260
5 for
10
1 seconds
(3) Measuring resistance
1 hour after test
(1) Vibration frequency:
R:
(0.5%+ 0.05)
Without mechanical damage
10Hz to 55Hz to10Hz in 60
such as break
seconds as a period
(2) Vibration time: period
cycled for 2 hours in each
of 3 mutual perpendicular
directions
(3) Amplitude: 1.5mm
(1) Peak value: 490N
R:
(0.25%+ 0.05)
Without mechanical damage (2) Duration of pulse: 11ms
(3) 3 times in each positive
such as break
and negative direction of 3
mutual perpendicular
directions
Resistance to
Solder Heat
Vibration
Shock
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
