LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* Low power consumption.
* High efficiency.
* Versatile mounting on p.c. board or panel.
* I.C. compatible/low current requirement.
* Popular T-1 diameter.
Package Dimensions
Part No.
LTW-42NC5-DL
Lens Color
Water Clear
Emitted Color
InGaN White
NOTES:
1. All dimensions are in millimeters (inches).
2. Tolerance is
±0.25mm(.010")
unless otherwise noted.
3. Protruded resin under flange is 1.0mm(.04") max.
4. Lead spacing is measured where the leads emerge from the package.
5. Specifications are subject to change without notice.
Part No. : LTW-42NC5-DL
BNS-OD-C131/A4
Page :
1
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Absolute Maximum Ratings at T
a
=25
℃
PARAMETER
Power Dissipation
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
DC Forward Current
Reverse Voltage
Operating Temperature Range
Storage Temperature Range
Lead Soldering Temperature
[1.6mm(.063") From Body]
100
30
5
-25℃ to + 80℃
-30℃ to + 100℃
260℃ for 5 Seconds
mA
mA
V
MAXIMUM RATING
120
UNIT
mW
Part No. : LTW-42NC5-DL
BNS-OD-C131/A4
Page :
2
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Electrical / Optical Characteristics at Ta=25
℃
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
TEST CONDITION
Luminous Intensity
Viewing Angle
Iv
2θ
1/2
x
400
1100
45
0.30
0.30
3.5
4.0
100
mcd
deg
I
F
= 20mA
Note 1,2,3
Iv Spec. Table
Note 4
I
F
= 20mA
Note 5
Hue Spec. Table &
Chromaticity Diagram
Chromaticity Coordinates
y
Forward Voltage
Reverse Current
V
F
I
R
V
μA
I
F
= 20mA
V
R
= 5V
NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
eye-response curve.
2. The Iv guarantee should be added
±15﹪tolerance.
3. Iv classification code is marked on each packing bag.
4.
θ
1/2
is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
5. The chromaticity coordinates (x, y) is derived from the 1931 CIE chromaticity diagram.
6. Precautions in handling:
‧
When soldering, leave 2mm of minimum clearance from the resin to the soldering point.
‧
Dipping the resin to solder must be avoided.
‧
Correcting the soldered position after soldering must be avoided.
‧
In soldering, do not apply any stress to the lead frame particularly when heated.
‧
Lead forming must be done before soldering.
‧
It is necessary to cut the lead frame at normal temperature.
7. Caution in ESD:
Static Electricity and surge damages the LED. It is recommend to use a wrist band or
anti-electrostatic glove when handling the LED. All devices, equipment and machinery
must be properly grounded.
Part No. : LTW-42NC5-DL
BNS-OD-C131/A4
Page :
3
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Typical Electrical / Optical Characteristics Curves
(25℃ Ambient Temperature Unless Otherwise Noted)
Part No. : LTW-42NC5-DL
BNS-OD-C131/A4
Page :
4
of
9
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Packing Spec
1,000 pcs per packing bag
10 packing bags per inner carton
Total 10,000 pcs per inner carton
8 Inner cartons per outer carton
Total 80,000 pcs per outer carton
Part No. : LTW-42NC5-DL
BNS-OD-C131/A4
Page :
5
of
9
MicroPython开源版块
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
