PL-2515PRO
Advanced Hi-Speed USB Flash Disk Controller
Product Datasheet
Document Revision: 1.4D
Document Release: October 14, 2005
Prolific Technology Inc.
7F, No. 48, Sec. 3, Nan Kang Rd.
Nan Kang, Taipei 115, Taiwan, R.O.C.
Tel: 886-2-2654-6363
Fax: 886-2-2654-6161
Email:
sales@prolific.com.tw
URL:
http://www.prolific.com.tw
Tech:
http://tech.prolific.com.tw
Release Date
October 14, 2005
ds_pl2515PRO_v14D.doc
Disclaimer
All the information in this document is subject to change without prior notice. Prolific Technology Inc.
does not make any representations or any warranties (implied or otherwise) regarding the accuracy
and completeness of this document and shall in no event be liable for any loss of profit or any other
commercial damage, including but not limited to special, incidental, consequential, or other damages.
Trademarks
The Prolific logo is a registered trademark of Prolific Technology Inc. All brand names and product
names used in this document are trademarks or registered trademarks of their respective holders.
Copyrights
Copyright © 2005 Prolific Technology Inc. All rights reserved.
No part of this document may be reproduced or transmitted in any form by any means without the
express written permission of Prolific Technology Inc.
PL-2515PRO Product Datasheet
-2-
Document Version 1.4D
Release Date
October 14, 2005
ds_pl2515PRO_v14D.doc
Revision History
Revision
1.4D
1.4C
1.4B
1.4
1.3
Description
Section 3.0: Modify Pin Description for pin RPU
Correct the Outline Diagram for LQFP64 (10x10mm).
Add Lead (Pb) Free Ordering Information.
Remove watermark on Outline Diagram.
Modify Pin Diagram, Pin Assignment and Outline
Diagram for new IC packaging.
Revised Datasheet for Single Channel Mode controller
IC only.
Modified Features section on page 5:
o
Single Mode max performance can reach up to
11MB/s Read and 8MB/s Write.
o
Add support for 8Gbit NAND Flash.
o
Total maximum capacity can be up to 16Gbyte (for 2A
chip and later versions).
o
Add S/W write-protect feature.
o
Add CD-ROM Emulation (for 2A chip and later).
Edit the Overview and Chip Configuration section.
Correct Page 9 - Pin Assignment Table: LCD (LCD
Indicator) to LED (LED Indicator).
Added Disclaimer, Trademarks, Copyrights section.
Added List of Figures and List of Tables section.
Added Ordering Information.
Change pin 59 CLOCK_SEL to NC – the operation clock
of internal MCU 8032 is always 60MHz.
Product Datasheet – Initial Release.
Date
October 14, 2005
March 15, 2005
March 1, 2005
July 27, 2004
July 15, 2004
1.2
June 11, 2004
1.1
1.0
May 28, 2004
April 1, 2004
PL-2515PRO Product Datasheet
-3-
Document Version 1.4D
Release Date
October 14, 2005
ds_pl2515PRO_v14D.doc
Table of Contents
1.0 FEATURES ......................................................................................................... 6
2.0 OVERVIEW......................................................................................................... 7
2.1 Chip Configuration .................................................................................................... 8
3.0 PIN ASSIGNMENT AND DESCRIPTION ......................................................... 10
3.1 Pin Assignment and Description of PL-2515PRO LQFP64..................................... 10
3.2 Pin Assignment and Description of PL-2515PRO LQFP48..................................... 12
4.0 USB PORT DESCRIPTOR ............................................................................... 14
4.1 USB Descriptor of Embedded Hub.......................................................................... 14
4.2 USB Descriptor of Auxiliary Mass Storage Device .................................................. 16
4.3 USB Descriptor of Primary Mass Storage Device ................................................... 18
5.0 DC CHARACTERISTICS.................................................................................. 21
5.1 Absolute Maximum Ratings .................................................................................... 21
5.2 Recommended Operation Conditions ..................................................................... 21
5.3 General DC Characteristics..................................................................................... 21
5.4 DC Electrical Characteristics for 3.3 V Operation ................................................... 22
6.0 ORDERING INFORMATION............................................................................. 22
7.0 OUTLINE DIAGRAM ........................................................................................ 23
7.1 PL-2515PRO LQFP64pin (10mm x 10mm x 1.4mm) Outline Diagram................... 23
7.2 PL-2515PRO LQFP48pin (7mm x 7mm x 1.4mm) Outline Diagram....................... 24
PL-2515PRO Product Datasheet
-4-
Document Version 1.4D
Release Date
October 14, 2005
ds_pl2515PRO_v14D.doc
List of Figures
Figure 1-1 Block Diagram of PL-2515PRO............................................................................. 6
Figure 3-1 Pin Assignment of PL-2515PRO LQFP64 (10x10) .............................................. 10
Figure 3-2 Pin Assignment of PL-2515PRO LQFP48 (7x7) .................................................. 12
Figure 7-1 Outline Diagram of PL-2515PRO LQFP64 (10x10mm)....................................... 23
Figure 7-2 Outline Diagram of PL-2515PRO LQFP48 (7x7mm)........................................... 24
List of Tables
Table 2-1 PL-2515PRO Partition Configurations .................................................................... 8
Table 3-1 Pin Descriptions of PL-2515PRO LQFP64 ............................................................11
Table 3-2 Pin Descriptions of PL-2515PRO LQFP48 ........................................................... 13
Table 4.1.1 Device Descriptor of Embedded Hub ................................................................. 14
Table 4.1.2 Configuration Descriptor of Embedded Hub....................................................... 15
Table 4.1.3 Interface Descriptor of Embedded Hub .............................................................. 15
Table 4.1.4 Interrupt Endpoint Descriptor ............................................................................. 15
Table 4.1.5 Hub Descriptor of Embedded Hub ..................................................................... 16
Table 4.2.1 Device Descriptor of Auxiliary Mass Storage Device.......................................... 16
Table 4.2.2 Configuration Descriptor of Auxiliary Mass Storage Device ............................... 17
Table 4.2.3 Interface Descriptor of Auxiliary Mass Storage Device....................................... 17
Table 4.2.4 Bulk Out Endpoint Descriptor (Endpoint 1)......................................................... 18
Table 4.2.5 Bulk In Endpoint Descriptor (Endpoint 2) ........................................................... 18
Table 4.3.1 Device Descriptor of Primary Mass Storage Device........................................... 19
Table 4.3.2 Configuration Descriptor of Primary Mass Storage Device ................................ 19
Table 4.3.3 Interface Descriptor of Primary Mass Storage Device........................................ 20
Table 4.3.4 Bulk Out Endpoint Descriptor (Endpoint 1)......................................................... 20
Table 4.3.5 Bulk In Endpoint Descriptor (Endpoint 2) ........................................................... 20
Table 5.1 Absolute Maximum Ratings................................................................................... 21
Table 5.2 Recommended Operation Conditions ................................................................... 21
Table 5.3 General DC Characteristics................................................................................... 21
Table 5.4 DC Electrical Characteristics for 3.3V Operation .................................................. 22
Table 6.1 Ordering Information ............................................................................................. 22
PL-2515PRO Product Datasheet
-5-
Document Version 1.4D