Anti-Sulfurated Thick Film Chip Resistors
Document No.
TRMS-XX0S001J
Revise Date
page number
2016/06/14
4/13
( RMS series standard )
Halogen-Free
AEC-Q200 qualified
5.1
Derating Curve :
For resistors operated at ambient temperature over 70℃ , power rating shall be derated in
accordance with figure 1.
P max.
Power ratio (%)
125
RMS02
RMS04/06/10
RMS12/13/20/25
Ambient
Temp. (
°C
)
Figure 1
5.2
Rated Voltage:
The rated voltage is calculated by the following formula:
E=
P*R
E=
Rated Voltage(V)
P=
Rated Power(W)
R=
Resistance Value
(Ω)
E.G. : What is RMS06JT102 the rated voltage ?
RMS06JT102
E=
P:1/10W
;
R:102 = 1KΩ = 1000Ω
0.1(W) * 1000(Ω)
= 10 (V)
TA-I TECHNOLOGY CO., LTD
Anti-Sulfurated Thick Film Chip Resistors
Document No.
TRMS-XX0S001J
Revise Date
page number
2016/06/14
5/13
( RMS series standard )
Halogen-Free
AEC-Q200 qualified
6. Reliability Tests:
Test Items
Reference standard
-At
Condition of Test
+25/–55 °C and +25/+125 °C
Test Limits
△R
Refer 5.0
±(1%
+ 0.05Ω )
Remarks :
0201:
±(3%
+ 0.1Ω )
0402 :
±(2%
+ 0.1Ω )
0Ω : 50mΩ or less
0.5%,1%:±(1.0%+0.05Ω)
2%,5%:±(2.0%+0.1Ω)
0201 :
±(3%
+ 0.1Ω )
0Ω : 50mΩ or less
Temperature Coefficient
IEC 60115-1 4.8
of Resistance
Short Time Overload
IEC60115-1 4.13
2.5 X rated voltage
for
5 sec
High Temperature
Exposure (Storage)
AEC-Q200-REV C-Test 3
MIL-STD-202 Method 108
1000 hrs. @ T=125°C. Unpowered.
Measurement at 24±2 hours after test
conclusion.
Moisture Resistance
AEC-Q200-REV C-Test 6
MIL-STD-202 Method 106
0.5%,1%:±(1.0%+0.05Ω)
T=24 hours / Cycle ,10Cycles . Notes : 2%,5%:±(2.0%+0.1Ω)
Steps 7a& 7b not required. Unpowered . 0201 :
±(3%
+ 0.1Ω )
0Ω : 50mΩ or less
1000 hours 85°C/85%RH. Note: Specified
±(3%
+ 0.1Ω )
conditions: 10% of operating power(not
0201 :
±(5%
+ 0.1Ω )
exceeding max working voltage).
Measurement at 24±2 hours after test
0Ω : 100mΩ or less
conclusion.
1000 hours TA=70°C at rated power.
Measurement at 24±2 hours after test
conclusion.
Electrical test not required.
Inspect device construction, marking and
workmanship.
Verify physical dimensions to the
applicable device detail specification. Note:
User(s) and Suppliers spec. Electrical test
not required.
a:Isopropyl Alcohol：Mineral Spirits= 1：3
b:Terpene Defluxer (Bioact EC-7R)
Marking and protective layer
c:Deionized water
：Propylene
Glycol
can not be detached
Monomethyl Ether：monoethanolamine =
42：1：1
Wave Form : Tolerance for half sine shock
±(1%
+ 0.1Ω )
pluse.
Peak value is 100g’s. Normal
0Ω : 50mΩ or less
duration(D) is 6(ms)
5 g's for 20 min., 12 cycles each of 3
orientations. Note: Test from 10-2000 Hz.
±(1%
+ 0.1Ω )
0Ω : 50mΩ or less
0.5%,1%:
±(1%
+ 0.1Ω )
2%.5% :
±(3%
+ 0.1Ω )
0201 :
±(5%
+ 0.1Ω )
0Ω : 100mΩ or less
Biased Humidity
AEC-Q200-REV C-Test 7
MIL-STD-202 Method 103
Operational Life
AEC-Q200-REV C-Test 8
MIL-STD-202 Method 108
External Visual
Physical
Dimension
AEC-Q200-REV C-Test 9
MIL-STD-883 Method 2009
AEC-Q200-REV C-Test 10
JESD22 Method JB-100
Resistance to
Solvents
AEC-Q200-REV C-Test 12
MIL-STD-202 Method 215
Mechanical Shock
AEC-Q200-REV C-Test 13
MIL-STD-202 Method 213
AEC-Q200-REV C-Test 14
MIL-STD-202 Method 204
Vibration
Resistance to Soldering
AEC-Q200-REV C-Test 15
MIL-STD-202 Method 210
Heat
0.5%,1% :
±(0.5%
+ 0.05Ω )
Condition B :
2%.5% :
±(1%
+ 0.1Ω )
Immerse the specimens in and eutectic
0201 :
±(2%
+ 0.1Ω )
solder at 260±5℃ for 10±1S .
0Ω : 50mΩ or less
Thermal Shock
AEC-Q200-REV C-Test 16
MIL-STD-202 Method 107
-
55°C/+155°C. Note: Number of cycles
required-300, Maximum transfer time-20
seconds, Dwell time-15 minutes. Air-Air.
±(1%
+ 0.1Ω )
0201 :
±(2%
+ 0.1Ω )
0Ω : 50mΩ or less
TA-I TECHNOLOGY CO., LTD
stm32/stm8
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
