(
)
HAOYU (HONG KONG) LIMITED
SPECIFICATION
SERIES
DRAWN
1
2
RATING
6.35 PHONE JACK (DIP) 6.35
LI JIAN
DC50V 1A
B-2
TYPE
APVD
CONSTRUCTION DIMENSION
HY-WI-32
2008-07-23
1
3
Apply to the appended drawing.
OPERATING TEMPERATURE RANGE
-20 ~70
PRESERVATIVE TEMPERATURE RANGE
15
~35
ITEM
3
TEST CONDITIONS
SPECIFICATIONS
ELECTRICAL PERFORMANCE
MEASURED BY THE CONTACT RESISTANCE APPARATUS OR m
CONTACT
METER AT 0.1A DC5V .THE RESULT IS THE AVERAGE OF5
SUCCESSIVE MEASUREMENTS.
5V
5
A VOLTAGE OF 250V DC SHALL BE APPLIED
FOR 1 MIN. AFTER WHICH MEASUREMENT SHALL BE MADE.
INSULATION
BETWEEN TERMINALS
BETWEEN INDIVIDUAL TERMINALS AND FRAME
250V DC
(1)
(2)
1
,
100M
100
min
.
0.1A
70m
70
max
3A
RESISTANCE
3B
RESISTANCE
A VOLTAGE OF250V AC SHALL BE APPLIED
FOR 1 MIN. AFTER WHICH MEASUREMENT SHALL BE MADE.
DIELECTRIC
3C
STRENGTH
BETWEEN TERMINALS
BETWEEN INDIVIDUAL TERMINALS AND FRAME
250V AC
(3)
(4)
4.MECHANICAL PERFORMANCE(
INSERTION
AND
WITHDRAW
FORCE
)
Insertion and extraction force
3-40N
3-40
1
,
WITHOUT DAMAGE
TO PARTS ARCING
OR BREAKDOWN ETC
.
Being measure at across spring piece and across matching plug for ergometer
(
)
4A
ELECTRICAL
SHALL
BE
CHARACTERISTICS
SATISFIED.WITHOUT
TERMINAL
4B
STRENGTH
A STATIC LOAD OF 10 N(1000gf) SHALL BE APPLIED TO THE TIP OF
THE TERMINALS FOR 60 SEC. IN ANY DIRECTION
10N(1000gf)60
DAMAGE OR EXCESSIVE LOOSEN-ESS
OF ACTUATOR
\
.
UNLESS OTHERWISE SPECIFIED. THE STANDRD RANGE
STANDARD
4C
ATMOSPHEIC
CONDITIONS
OF ATMOSPHERIC CONDITIONS FOR MAKING MEASUREMENTS
AND TESTS ARE AS FOLLOWS:
AMDIENT TEMPERATURE: 15
RELATIVE HUMIDITY
AIR PRESSURE
TO 35
1
2
3
15
~35
:25% TO 75%RH
25% ~ 75%RH
80Kpa ~106Kpa
:80Kpa TO 106Kpa
(
)
HAOYU (HONG KONG) LIMITED
SPECIFICATION
B-2
HY-WI-32
2008-07-23
2
3
5 DURABILITY
WITHOUT DEFORMATION OF CASE
RESISTANCE
TO
5A
SOLDERING
HEAT
TEST
OR
THE TOP OF THE TERMINALS SHALL BEDIPPED 2mm .
THE PLASTIC BODY IS 1.6mm ABOVE THE TIN LIGUID.
2mm ,
1.6mm
Wave-soldering is to be performed within 3seconds at 260 +/-5
260 +/-5
3
Hand weilding to be performed within 3 seconds at 380
or
below.
380
3 0.5
EXCESSIVE
TERMINALS
ELECTRICAL
SHALL
BE SATISFIED.
CHARACTERISTICS
LOOSENESS
OF
5B
LIFE TEST.
WITHOUT LOAD
IT IS TESTED BY MACHINE
ACTING FORCE MUST BE PARALLED TO THE WAY OF
PUSHING
AN ACTUATOR SHALL BE SUBIECT TO 5000 CYCLES
AT A SPEED OF30 CYCLES FOR 1 MIN
30
5000
1
2
1
2
CONTACT
RESISTANCE
SHALLBE 200m max
MECHANICAL
AND
ELECTRICAL
CHARACTERISTICS SHALL
BESATISFIED
200m
85 2
5C
HEAT TEST.
FOR 48 HOURS AFTER TEST KEEP IN NORMAL
CONDITION FOR 30 MINUTES.
85 2
48
,
30
THERE SHALL BE NO DAMAGE ON
40
2
90-96%RH FOR 48 HOURS, TEST AFTER
APPEARANCE
MECHANICAL AND ELECTRICAL
CHARACTERISTICS
SATISFIED
FOR 48 HRS. AFTER TEST KEEP IN
SHALL
BE
5D
HUMIDITY TEST.
KEEPING IN NORMAL CONDITION FOR 30 MIN.
40 2
30
AT –40 2
90
96
RH
48
5E
COLD TEST.
NORMAL CONDITION FOR 30 MIN.
-40 2
48
,
30
SALT SPRAY TEST
5F
AT 5% NACL LIQUOR FOR 24HOURS, AFTER WASHING,
KEEP IN NORMAL CONDITION FOR 30 MIN.
5% Nacl
24
30
WITHOUT EXCESSIVE CORROSION
OR CRACK IN APPEARANCE
6
APPLICATION NOTES:
(
)
HAOYU (HONG KONG) LIMITED
SPECIFICATION
B-2
HY-WI-32
2008-07-23
3
3
,
ROSIN AND OTHER INSULATING AND CAUSTIC MATERIAL CAN NOT BE DIPPED INTO THE ROCKET DURING
SOLDERING.
2
PRODUCTS CAN NOT BE BLOWN WITH AIR GUN OR CLEANED WITH A SOLVENT AFTER SOLDERING.)
3
ALL PARTS OF THE PRODUCTS CAN NOT BE DISSOLVED BEFORE SOLDERING.
4
AVOID STORING THE PRODUCTS IN A PLACE AT HIGH TEMPERATURE, HIGH HUMIDITY AND
IN CORROSIVE GASES.)
5
:
,
180
.
,
,
SHELF LIFE IS LESS THAN 180 DAYS SINCE THE GOODS WARE SENT OUT FROM OUR FACTORY. OUR COMPANY
DOESN’T ACCEPT RESPONSIBILITY FOR REJECTS IF THE SHELF LIFE OF GOODS EXCEEDS 180 DAYS.
6
PLEASE FEEL FREE TO REPORT TO US IF YOU DISCOVER THE INFERIOR GOODS, SO THAT WE CAN TAKE NOTE,
CHECK, TRACK AND IMPROVE THEM. THANKS.
(
)
HAOYU (HONG KONG) LIMITED
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
