(
)
B-2
XLR
LIU FAZHAN
TYPE
APVD
HY-WI-32
2008-07-23
1
3
HAOYU (HONG KONG) LIMITED
SPECIFICATION
SERIES
DRAWN
1A.
RATED LOAD
SURFACE:
AS
DC 50V 3A
SHOWN
IN
THE
CONSTRUCTION DIMENSION
ZHOU ZHIQUAN
Apply to the appended drawing.
APPLICABLE DRAWING
2
OPERATING TEMPERATURE RANGE
-20 ~70
PRESERVATIVE TEMPERATURE RANGE
20 ~70
ITEM
3
TEST CONDITIONS
SPECIFICATIONS
ELECTRICAL PERFORMANCE
TO BE MEASURED AT 1kHz AND 100m A MAX. WHEN THE
CONTACT
MEASUREMENT SHALL BE MADE BY A MATING PLUG,
OXIDATION
FILM
ON
THE
SURFACE
MUST BE
WIPED.
50m
50
max
3A
RESISTANCE
RESISTANCE OF A PLUG CODE SHALL NOT BE INCLUDED AS A
MEASUREMENT VALUE.
1kHz 100mA
TO BE MEASURED BETWEEN ADJACENT TERMINALS AT 500V
INSULATION
3B
RESISTANCE
DC
DC500V
100M
100
min
.
DIELECTRIC
3C
STRENGTH
A VOLTAGE OF AC 1500VSHALL BE APPLIED BETWEEN
ADJACENT TERMINALS FOR 1 MIN. AT 50~60Hz
AC1500V 50~60Hz 1
WITHOUT DAMAGE
TO PARTS ARCING
OR BREAKDOWN ETC
.
4.MECHANICAL PERFORMANCE(
INSERTION
AND
WITHDRAW
FORCE
)
Insertion and extraction force
4~40N
4~40N
WITHOUT
LOOSING
AND
4A
THE FORCE WHEN A JACK SHALL BE INSERTED AND
EXTRACTED SLOWLY AFTER FIXING A MATING PLUG AS
SHOWN IN SECTION 1B TO THE PUSH-PULL SCALE.
TERMINAL
4B
STRENGTH
THE FORCE OF 4.9N SHALL BE APPLIED TO THE TERMINAL FOR
10 SEC(3 DIRECTION)
4.9N
10
BREAKDOWN.
TERMINAL
BEND SHALL BE ACCEPTED
UNLESS OTHERWISE SPECIFIED. THE STANDRD RANGE
STANDARD
4C
ATMOSPHEIC
CONDITIONS
OF ATMOSPHERIC CONDITIONS FOR MAKING MEASUREMENTS
AND TESTS ARE AS FOLLOWS:
AMDIENT TEMPERATURE: 15
RELATIVE HUMIDITY
AIR PRESSURE
TO 35
1
2
3
15
~35
:25%TO75%RH
25%~75%RH
80Kpa ~106Kpa
:80Kpa TO 106Kpa
(
)
B-2
HY-WI-32
2008-07-23
2
3
HAOYU (HONG KONG) LIMITED
SPECIFICATION
5
DURABILITY
WITHOUT DEFORMATION OF CASE
THE TOP OF THE TERMINALS SHALL BEDIPPED 2mm .
THE PLASTIC BODY IS 1.6mm ABOVE THE TIN LIGUID.
2mm ,
1.6mm
Wave-soldering is to be performed within 3seconds at 260 +/-5
260 +/-5
3
Hand weilding to be performed within 3 seconds at 380 or
below.
380
3 0.5
OREXCESSIVE
LOOSENESS
OF
RESISTANCE
TO
5A
SOLDERING
HEAT
TEST
TERMINALSELECTRICAL
CHARACTERISTICS SHALL
BE SATISFIED.
1
WITHOUT LOAD INSERTIONS AND EXTRACTIONS OF
5000 CYCLES SHALL BE MADE AT RATE OF 10 TO 20
CYCLES PER MINUTE
10~20/
5000
2
5B
LIFE TEST.
1
2
85 2
5C
HEAT TEST.
FOR 96 HOURS AFTER TEST KEEP IN NORMAL
1
CONTACT
RESISTANCE
SHALLBE 200m max
MECHANICAL
AND
ELECTRICAL
CHARACTERISTICS SHALL
BESATISFIED
200m
CONDITION FOR 1 HOUR.
85 2
96
,
40
2
90~96%RH FOR 96 HOURS, TEST AFTER
THERE SHALL BE NO DAMAGE ON
APPEARANCE
MECHANICAL AND ELECTRICAL
CHARACTERISTICS
SATISFIED
SHALL
BE
5D
HUMIDITY TEST.
KEEPING IN NORMAL CONDITION FOR 1 HOUR.
40 2
1
At –40 2
for 96 HRS. AFTER TEST KEEP IN NORMAL
90~96 RH
96
CONDITION FOR 1 HOUR.
5E
COLD TEST.
-40 2
96
,
1
SALT SPRAY TEST
5F
AT 5% NACL LIQUOR FOR 12HOURS, AFTER WASHING,
KEEP IN NORMAL CONDITION FOR 30 MIN.
5% Nacl
12
30
WITHOUT EXCESSIVE CORROSION
OR CRACK IN APPEARANCE
(
)
B-2
HY-WI-32
2008-07-23
3
3
HAOYU (HONG KONG) LIMITED
SPECIFICATION
6
APPLICATION NOTES:
,
ROSIN AND OTHER INSULATING AND CAUSTIC MATERIAL CAN NOT BE DIPPED INTO THE ROCKET DURING
SOLDERING.
2
PRODUCTS CAN NOT BE BLOWN WITH AIR GUN OR CLEANED WITH A SOLVENT AFTER SOLDERING.)
3
ALL PARTS OF THE PRODUCTS CAN NOT BE DISSOLVED BEFORE SOLDERING.
4
AVOID STORING THE PRODUCTS IN A PLACE AT HIGH TEMPERATURE, HIGH HUMIDITY AND
IN CORROSIVE GASES.)
5
:
,
180
.
,
,
SHELF LIFE IS LESS THAN 180 DAYS SINCE THE GOODS WARE SENT OUT FROM OUR FACTORY. OUR COMPANY
DOESN’T ACCEPT RESPONSIBILITY FOR REJECTS IF THE SHELF LIFE OF GOODS EXCEEDS 180 DAYS.
6
PLEASE FEEL FREE TO REPORT TO US IF YOU DISCOVER THE INFERIOR GOODS, SO THAT WE CAN TAKE NOTE,
CHECK, TRACK AND IMPROVE THEM. THANKS.
(
)
HAOYU (HONG KONG) LIMITED
stm32/stm8
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
