Doc. No.
Rev.
Sheet
SPEC-USB-001
A
1/7
USB C TYPE
This specification covers the requirements for product performance and test methods of HAOYU HONG KONG
LIMITED Manufacturing Center’s
USB
C TYPE plug and receptacle Connectors.
2-1 IEC512
2-2 MIL-STD 202
2-3 EIA-364
: 3A 30V AC/DC max
Rated : 3A 30V AC/DC max
3-2
:
:-20 + 60
Temperature Range: storage : -20
:-30 + 80
operating : -30
to +80
: +20
Nominal : +20
3-1
to +60
;
,
All tests shall be performed as bellow conditions unless otherwise specified.
4-2
:+ 15 + 35
Temperature range : +15 to +35
4-3
:25% - 85%
Humidity range: 25% to 85%
4-1
Doc. No.
Rev.
Sheet
SPEC-USB-001
A
2/7
5.
ITEM
Description
Test Methods
EIA364-18
Test Specification
5-1
Examination
of
Product Appearance
EIA364-18
Shall be confirmed with eyes in
accordance with each drawing.
Outward appearance shall be good
without such injurious problem and
structure shall be meet the design and
dimension requirement of drawing
ITEM
Description
Test Methods
EIA 364-13
12.5mm /min.
,
Test Specification
5N-20 N
The connector insertion force shall be
the range from 5N to 20N
6-1
Insertion force
EIA 364-13
Measure force at maximum rate of
12.5mm
(0.492")
per minute
EIA 364-13
EIA 364-13
,
12.5 mm /min.
8N-20 N
The connector extraction force shall be
the range from 8N to 20N
6-2
Measure force at maximum rate of
12.5mm(0.492") per minute
Extraction force
:
(40 m ,
10 m (Max)
6-3
Durability
EIA 364-09
10000
,
200
/
.
)
(5
(8
20N)
20 N)
Doc. No.
Rev.
Sheet
SPEC-USB-001
A
3/7
EIA 364-09
Type C :10000 cycles cycle
rate of 200cycles per
manually
Must meet the following criteria after
the cycle test is completed:
hour
- Contact resistance (40m
10m (Max) after test)
- Insertion force (5N to 20N)
- Extraction force (8N to 20N)
delta
- Visual inspection (no exposed base
metal on contacts)
6-4
Cable
Cable Flexing
EIA 364-41
X=
120
100
3.7
1ms
No discontinuity over 1 microsecond
EIA 364-41
100 cycles in each of 2 planes 120
degree.
Dimension x=3.7x cable diameter
6-5
Cable
Cable Pull-Out
EIA-364-38
40 N
1
During flexing or physical damage
allowed
EIA-364-38
40N steady state axial load for 1 minute
No discontinuity or physical damage
allowed
6-6
4-axes continuity
test
8N
10
;
0° 90° 180° 270°
1us,
8N tensile force for a period of 10
seconds Min; The specimen must
subject to
No discontinuity greater than 1us and
no physical damage to the specimen(one
cable per test)
EIA364-18
105
105
Visual inspection,Test shall be done
in sequences defined in
EIA364-1000.01
Doc. No.
Rev.
Sheet
SPEC-USB-001
A
4/7
ITEM
Description
Test Methods
EIA 364-21C
100V DC
.
100M
Test Specification
7-1
Insulation
Resistance
EIA 364-21C
Unmated connectors, apply 100Volts
DC between adjacent terminal or
ground.
EIA 364-23b
100M minimum(unmated)between
adjacent contacts and contacts and
shell
(40 m ,
Low Level
Contact
10
7-2
:20mV max.;
: 100m A max..
EIA 364-23b
20mV Max. open circuit at 100mA
Max.
EIA 364-20
m (Max))
40m (Max) initial for VBUS and GND
contacts and all other contacts; delta
10m (Max) after test
Resistance
100V AC
1
.
7-3
Dielectric
withstanding Voltage
EIA 364-20
Subjected to 100VAC (RMS) for 1
minute between adjacent terminals.
There shall be no breakdown
5.0 A
1.25 A
VCONN
A
VBUS
GND
0.25
30
USB
-C
25
7-4
Contact current
rating
EIA364-70
5.0A shall be applied collectively to
VBUS pins and 1.25 A applied to the
VCONN pin and 0.25 A the other
contacts.
When the currents are applied to the
contacts, the temperature rise shall
not exceed 30 °C at any point on the
USB Type-C mated plug and
receptacle under test, when measured
at an ambient temperature of 25 °C.
Doc. No.
Rev.
Sheet
SPEC-USB-001
A
5/7
ITEM
Description
EIA 364-17
Test Methods
105
72
120
105
:
Test Specification
;
: 40m
8-1
Temperature Life
EIA 364-17
105º C without applied voltage for 120 hours.
105º C without applied voltage for 72 hours
when used as preconditioning in EIA
364-1000.01.
EIA 364-32
Visual inspection, Test shall be
done in sequences defined in
EIA 364-1000.01.
10
8-2
Thermal Shock
-55 + -55
USB 3.0
EIA 364-32
10 Cycles 55
and +85
. The USB 3.0
There shall be no evidence of
any physical damage.
connectors under test must be mated.
MIL-STD-202F 101d
:
:
5±1%,
,
.
8-3
Salt Spray
B
: 35±2
: 48
,
.
MIL-STD-202F, Method 101D, Test Condition B
Subject mated connectors to 48 hours at 35
with 5%-Salt-solution concentration.
1).Shall meet visual
requirement, show no physical
damage.
2).Shall meet requirements of
additional tests as specified in
test sequence in Section 5
EIA 364-31
25
3
65
3
50% 3%
0.5
24
80%
,
3%
0.5
,
EIA 364 - 1000.01
FPGA/CPLD
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
