PRODUCT SPECIFICATION
SPEC. NO:
T-0621-005A
新弘智
CUSTOMER'S PRODUCT NAME:
EMTEK PRODUCT NAME:
HQC1008-36NJ-T1
DATE: Nov.27,2018
THIS SPECIFICATION IS:
□ FULLY ACCEPTED
□ DENIED
□ ACCEPTED UNDER THE FOLLOWING CONDITIONS
SIGNATURE:
NAME(PRINT):
TITLE:
DATE:
FACTORY:
本文件內容全部或部½,未經兆欣科技股½有限公
司同意不得以任½½式複½或其他用途
All rights reserved.This document or parts thereof,may
not be reproduced by any means or used in any manner
witout written permission of EMTEK CO.,LTD.
39,Chingao Rd.,(305)Hsinpu,
Hsinchu Hsien,Taiwan,R.O.C
TEL: 03-5894-433
FAX: 03-5894-523
1/7
SPEC. NO.
PRODUCT SPECIFICATION
1. Scope
This specification applies Ceramic Chip Inductance HQC1008-36N□-T1
to be delivered to user.
T-0621-005A
2. Product Identification
HQC 1008 - 36N
□
- T1
(1) (2) (3) (4) (5)
(1) Product name
(2) Shapes and dimensions
(3) Inductance
36N : 36 nH
(4) Tolerance
s=±0.3% , G=±2% , J=±5% , K=±10%
(5) Taping Type
3. Shapes and Dimensions
C
D
E
A
B
A max. : 2.90 mm
B max. : 2.54 mm
C max. : 2.03 mm
D ref.
E :
: 1.30 mm
0.45 ± 0.1 mm
Equivalent circuit
No Polarity
Drawn by
Checked by
Approved by
2/7
SPEC. NO.
PRODUCT SPECIFICATION
4. Electrical Characteristics
Customer
Part Number
Our Product
Part Number
HQC1008-36N□-T1
Inductance
(nH)/MHz
36/50
Inductance
Tolerance
G
J
K
75/350
1500
Q/MHz
Min.
SRF(Min.)
(MHz)
Rdc±20%
(Ω)
Irms Max.
(mA)
1300
T-0621-005A
Color Coding
1st
2nd
3rd
0.09
Orange Blue
Black
1. When ordering, please specify tolerance and packaging codes. Ex: HQC1008-36NJ-T1
Tolerance : s=±0.3% , G = ±2% , J = ±5% , K = ±10%
Packaging : Clear tape and reel { standard }.
2. L , Q、SRF : Agilent/HP E4991A+ Agilent/HP16197A
(The electrical specification test by the smallest gap position) or HP16193A
3. Rdc : Chroma Milliohmmeter 16502, or equivalent.
4. Irms for a 15℃ rise above 25℃ ambient.
5. Operating temperature range from -40℃ to 125℃.
6. Color coding is not necessarily same position.
5. Material list
Item
Core
Wire
Epoxy
Material
Al2O3 96%
Copper wire
UV Eopxy
3/7
PRODUCT SPECIFICATION
6.Reliability Test
Specifications
Item
Solderability
The metalized area must have 90%
minimum solder coverage.
SPEC. NO.
T-0621-005A
Test conditions
Dip pads in flux and dip in solder pot( 96.5 Sn/3.5 Ag
solder) at 255°C ±5°C.
Resistance
to
soldering
heat
There must be no case deformation or Inductors shall be reflowed onto a PC board using
change in dimensions.
the stated tolerance.
96.5 Sn/3.5 Ag solder paste.
of 260°C.
For 96.5 Sn/3.5 Ag solder paste:>217°C for 90 seconds
Inductance must not change more than Solder process shall be at a maximum temperature
Vibration
There must be no case deformation or Solder specimen inductor on the test printed circuit
board. Apply vibrations in each of the x,y and z
change in dimensions.
Inductance must not change more than directions for 2 hours for a total of 6 hours.
the stated tolerance.
Frequency : 10~50 Hz
Amplitude
: 1.5mm
There must be no case deformation or Inductors shall be subjected to temperature 125±2℃
High
for 50±12 hours.
temperature
change in dimensions.
resistance
Inductance must not change more thanMeasure the test items after leaving the inductors at
the stated tolerance.
room temperature and humidity for 2 hours.
Static
Humidity
Inductors must not have a shorted or Inductors shall be subjected to temperature 85±2℃
and 90 to 95%RH. for ten 24-hours.
openwinding.
Measure the test items after leaving the inductors
at room temperature and humidity for 2 hours.
Component
Inductors shall be subjected to 1.8Kg Inductors shall be reflow soldered (255°C ±5°C for
10 seconds) to a tinned copper substrate.
adhesion
A force gauge shall be applied to the side of the
(push test)
component.
The device must withstand the stated force
without a failure of the termination.
4/7
PRODUCT SPECIFICATION
SPEC. NO.
T-0621-005A
Specifications
Test conditions
Item
There must be no case deformation or Inductors shall be subjected to temperature
Low
-40±2℃ for 48±12 hours.
temperature
change in dimensions.
Measure the test items after leaving the inductors
resistance
Inductance must not change more
than the stated tolerance.
at room temperature and humidity for 1 to 2
hours.
Resistance
to
solvent
There must be no case deformation,
change in dimensions, or obliteration
of marking.
Inductors must withstand 6 minutes of alcohol or water.
Thermal
shock
There must be no case deformation or Inductors shall be subjected to 10 cycles to the
the following temperature cycle:
change in dimensions.
Inductance must not change more
than the stated tolerance.
1 cycle
+125℃
30 min.
30 sec
-40℃
30 min.
Measure the test items after leaving the inductors
at room temperature and humidity for 2 hours.
消费电子
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
