PRODUCT SPECIFICATION
SPEC. NO:
T-0622-063
新弘智
CUSTOMER'S PRODUCT NAME:
EMTEK PRODUCT NAME:
LCF1206-Series
DATE:Jul.26,2018
THIS SPECIFICATION IS:
□ FULLY ACCEPTED
□ DENIED
□ ACCEPTED UNDER THE FOLLOWING CONDITIONS
SIGNATURE:
NAME(PRINT):
TITLE:
DATE:
本文件內容全部或部½,未經兆欣科技股½有限公
司同意不得以任½½式複½或其他用途
All rights reserved.This document or parts thereof,may
not be reproduced by any means or used in any manner
witout written permission of EMTEK CO.,LTD.
FACTORY:
39,Chingao Rd.,(305)Hsinpu,
Hsinchu Hsien,Taiwan,R.O.C
TEL: 03-5894-433
FAX: 03-5894-523
2/8
PRODUCT SPECIFICATION
4. Electrical Characteristics
Customer
Part Number
Our Product
Part Number
LCF1206-3R3□-T
Q
Inductance
Inductance
/MHz
(nH)/MHz
Tolerance
Min.
3300/7.9
J,K
25/7.9
SRF
(MHz)
Min.
240
SPEC. NO.
T-0622-063
Rdc
(Ω)
Max.
1.32
Idc
(mA)
Min.
400
Irms
(mA)
Min.
450
Color Coding
1st
2nd
3rd
Red
Orange Orange
1. All specifications are calibrated with Coilcraft 1206 series
2. When ordering, please specify tolerance and packaging codes. Ex: LCF1206-3R3J-T
Tolerance :J = ±5%，K=±10%
Packaging : Clear tape and reel { standard }. *
3. L , Q , SRF: Agilent E4991A RF Impedance/Material Analyzer+ Agilent 16197A Test Fixtures
(The electrical specification test by the smallest gap position), or equivalent
4. Rdc : Chroma 16502 Milliohm meter, or equivalent.
5. Irms for a 25℃ rise above 25℃ ambient.
6. Operating temperature range from -40℃ to 125℃.
* Parts/Reel: 7” 2,000 Tape Width: 8mm
7. Idc for Inductance drop 10% from its value without current.
4/8
PRODUCT SPECIFICATION
6. Reliability Test
Item
Solderability
SPEC. NO.
T-0622-063
Specifications
The metalized area must have 90%
minimum solder coverage.
Test conditions
Dip pads in flux and dip in solder pot( 96.5 Sn/3.5 Ag
solder) at 255°C ±5°C.
Resistance to
soldering heat
There must be no case deformation or
change in dimensions.
Inductance must not change more than
the stated tolerance.
Inductors shall be reflowed onto a PC board using
96.5 Sn/3.5 Ag solder paste.
Solder process shall be at a maximum temperature
of 260°C.
For 96.5 Sn/3.5 Ag solder paste:>217°C for 90 seconds
Vibration
There must be no case deformation or
change in dimensions.
Inductance must not change more than
the stated tolerance.
Solder specimen inductor on the test printed circuit
board. Apply vibrations in each of the x,y and z
directions for 2 hours for a total of 6 hours.
Frequency : 10~50 Hz
Amplitude : 1.5mm
High
temperature
resistance
There must be no case deformation or
change in dimensions.
Inductance must not change more than
the stated tolerance.
Inductors shall be subjected to temperature 125±2℃
for 50±12 hours.
Measure the test items after leaving the inductors at
room temperature and humidity for 2 hours.
Static
Humidity
Inductors must not have a shorted or
openwinding.
Inductors shall be subjected to temperature 85±2℃
and 90 to 95%RH. for ten 24-hours.
Measure the test items after leaving the inductors
at room temperature and humidity for 2 hours.
Component
adhesion
(push test)
Inductors shall be subjected to 1.0Kg
Inductors shall be reflow soldered (255°C ±5°C for
10 seconds) to a tinned copper substrate.
A force gauge shall be applied to the side of the
component.
The device must withstand the stated force
without a failure of the termination.
单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
