BK16 SERIES
Positive Temperature Coefficient (PTC) Data Sheet
Features
■
■
■
■
■
■
■
Radial leaded devices.
Over-current protection
Faster tripping, typical application in micro-motors for automobiles.
Flame retardant epoxy polymer insulating material meets UL94 V-0 requirement.
Available in lead-free version.
Meets MSL level 1, per J-STD-020
Safety certification: UL: E244500
Dimensions (Unit: mm)
Part
Number
BK16-300
BK16-400
BK16-500
BK16-600
BK16-700
BK16-800
BK16-900
BK16-1000
BK16-1100
BK16-1200
BK16-1400
A
Max.
9.0
10.0
10.7
13.5
13.5
14.5
15.0
18.0
18.0
22.5
24.0
B
Max.
12.0
13.0
15.0
15.0
18.0
20.0
23.0
24.5
24.5
25.0
28.0
C
±0.6
5.1
5.1
5.1
5.1
5.1
5.1
5.1
10.5
10.5
10.5
10.5
D
Max.
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
E
Typ.
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
F
Min.
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6
Revision：05-Jun-15
www.brightking.com
BK16 SERIES
Electrical Characteristics
Part
Number
BK16-300
BK16-400
BK16-500
BK16-600
BK16-700
BK16-800
BK16-900
BK16-1000
BK16-1100
BK16-1200
BK16-1400
I
H
(A)
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
11.0
12.0
14.0
I
T
(A)
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
28.0
V
MAX
(V
DC
)
16
16
16
16
16
16
16
16
16
16
16
I
MAX
(A)
100
100
100
100
100
100
100
100
100
100
100
R
MAX
(Ω)
0.072
0.043
0.030
0.025
0.019
0.0145
0.012
0.011
0.010
0.009
0.008
R
MIN
(Ω)
0.020
0.018
0.014
0.009
0.008
0.006
0.004
0.004
0.003
0.003
0.003
Pd
typ.
(W)
2.3
2.4
2.6
2.8
3.0
3.0
3.3
3.7
3.7
4.2
4.2
·I
H
= Hold current: maximum current device will pass without tripping in 25℃ still air.
·I
T
= Trip current: minimum current at which the device will trip in 25℃ still air.
·V
MAX
= Maximum voltage device can withstand without damage at rated current.
·I
MAX
= Maximum fault current device can withstand without damage at rated voltage.
·R
MAX
= Maximum resistance of device in initial (un-soldered) state.
·R
MIN
= Minimum resistance of device in initial (un-soldered) state.
·Pd
typ.
= Typical power dissipation from device when in the tripped state at 25℃ still air.
Thermal Derating Chart – I
H
(A)
Part
Number
BK16-300
BK16-400
BK16-500
BK16-600
BK16-700
BK16-800
BK16-900
BK16-1000
BK16-1100
BK16-1200
BK16-1400
Maximum Ambient Operating Temperatures (
℃
)
-20
3.96
5.28
6.60
7.92
9.24
10.56
11.88
13.20
14.52
15.84
18.48
0
3.60
4.80
6.00
7.20
8.40
9.60
10.80
12.00
13.20
14.40
16.80
25
3.00
4.00
5.00
6.00
7.00
8.00
9.00
10.00
11.00
12.00
14.00
30
2.88
3.84
4.80
5.76
6.72
7.68
8.64
9.60
10.56
11.52
13.44
40
2.64
3.52
4.40
5.28
6.16
7.04
7.92
8.80
9.68
10.56
12.32
50
2.40
3.20
4.00
4.80
5.60
6.40
7.20
8.00
8.80
9.60
11.20
60
2.13
2.84
3.55
4.26
4.97
5.68
6.39
7.10
7.81
8.52
9.94
70
1.83
2.44
3.05
3.66
4.27
4.88
5.49
6.10
6.71
7.32
8.54
85
1.56
2.08
2.60
3.12
3.64
4.16
4.68
5.20
5.72
6.24
7.28
Revision：05-Jun-15
www.brightking.com
BK16 SERIES
Test Procedures and Requirement
Items
Resistance
Time to Trip
Hold Current
Trip Cycle Life
Trip Endurance
Test Conditions
In still air @25℃
Specified current, V
max
, 25℃
30 min, at I
H
V
max
, I
max
, 100 cycles
V
max
, 24hours
Accept/Reject Criteria
R
min
≤
R
≤
R
max
T
≤
max. Time to trip (T
trip
)
No trip
No arcing or burning
No arcing or burning
Typical Time-to-Trip Charts @25℃
Storage Recommendations
■
■
■
■
Storage Temperature: -10
℃
~+40
℃
Relative Humidity:
≤80%RH
Keep away from corrosive atmosphere and sunlight.
Period of Storage: 1 year.
Revision：05-Jun-15
Time to Trip (s)
www.brightking.com
BK16 SERIES
Wave Soldering Recommendation Parameters
300
3~5s
Soldering
250
200
150
100
50
0
0
245℃~260℃
100℃~130℃
Cooling
50
100
Time (s)
150
200
250
Items
Pre-Heating Zone
Soldering Zone
Cooling Zone
Conditions
Refer to the condition recommended by the flux manufacturer.
Maximum ramping rate should not exceed 4
℃
/sec.
Maximum solder temperature should not exceed 260℃
Forced cooling
Manual Soldering Recommendation Parameters
Items
Soldering condition
Soldering time
Soldering position
Conditions
The highest power of the manual soldering iron should be 30W or less, soldering
temperature should not be higher than 280℃.
The soldering time should be kept within 3 seconds, otherwise it might cause
insulation layer cracking, and increased part resistance.
The distance on the leads between the soldering point and bottom of the PPTC
body should be equal or greater than 4mm.
The soldering iron should not contact the PPTC body except the leads. If the
soldering conditions are kept to lower temperature, less time and larger distance,
the outcome of the soldering will be better.
Other
Notes: 1. Before using the device must be stored in the original bags, if the storage conditions do not guarantee,
the device may not be able to meet the given value.
2. The devices can’t used for reflow soldering.
Revision：05-Jun-15
www.brightking.com
BK16 SERIES
Mechanical Characteristics
Items
Tensile strength
Bending strength
Vibration
Specifications
No visible damage
No visible damage
No visible damage
Test Conditions/Methods
1.0Kgf, 10 seconds
0.5Kgf, 90°, 3 times
Freq: 10-55Hz, Amp: 0.75mm, 1min
Reliability Test
Items
Solder ability
Resistance to
soldering heat
Damp heat,
steady state
Temperature
cycling
Specifications
No visible damage，Solder OK,
Solder area
≥95%
No visible damage,
Electrical OK,
│△R/R0│≦50%
No visible damage, Electrical OK,
│△R/R0│≦20%
No visible damage, Electrical OK,
│△R/R0│≦20%
Test Conditions/Methods
245±5℃, 2±1s, dipping depth=0.5inch max
from the body
260±5℃, 10+2/-0s
40±2℃, 90~95 % RH, total 48Hrs, after 4Hrs
test electrical parameter
Ta＝-10+0/-1℃ 30min, Ta＝70+1/-0℃ 30min,
5cycles, after 1hr test electrical parameter
Packaging
Bag
Part
Number
BK16-300
150×200
BK16-400
BK16-500
120×150
BK16-600
Inner Box
BK16-700
BK16-800
BK16-900
BK16-1000
BK16-1100
BK16-1200
BK16-1400
150×200
200pcs/bag
800pcs/box
150×200
500pcs/bag
2000pcs/box
Dimension
A×B (mm)
Quantity
1000pcs/bag
4000pcs/box
500pcs/bag
2000pcs/box
Revision：05-Jun-15
www.brightking.com
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
