承
客戶名稱及編號:
CUSTOMER:
産品名稱:
DESCRIPION:
産品型號:
MODEL NO:
本司料號:
OUR PART NO:
客戶料號:
CUSTOMER PART NO:
承認書編號:
SPECIFICATION NO:
日期:
DATE:
WRITTEN
制定:
雷艳平
承認書附頁：圖紙,規格書
認
書
K4625
SPECIFICATION FOR APPROVAL
TOGGLE SWITCH
MT-1-102-A001-M200-RS
SM00751ZUR
C312274
YF-ENG-F-30113
2019-3-11
APPROVAL
審核:
客户承認欄
CUSTOMER APPROVAL SIGNATURE
MODEL NO.:
PART NO.:
APPROVED NO.:
DATE:
深圳市寶安區福永鎮第一工業區
24
棟
Tel:0755-33809280~3Fax:0755-33809285
YuenFung Electrnoic(shenzhen)Co.ltd
源丰电子(深圳）有限公司
承认书编号
YF-ENG-F-30113
A/0
第1页 共3页
2018-9-11
SPECIFICATION
规格书
WRITTEN
制定
版
页
本
次
发布日期
审
核
邓颖恒
APP'D审批
MODELSERIESNAME系列名称:
MODEL NO
产品型号:
1.RATING
额定值:
2.FFUNCTION
接触型式:
3.CIRCUITRY TRAIT:
TOGGLE SWITCH
MT-1-102-A001-M200-RS
2A 250VAC 5A 125VAC
SPDT 3P
ON-ON
4.ELECTRICAL CHARACTERISTICS
电气性½规格:
ITEM项目
4.1
CONTACT
RESISTANCE
接触电阻
TEST CONDITIONS
测试条件
MEASURED AT SMALL CURRENT(100mA OR LESS)1000Hz
在微小电流(100mA)以下测试.
APPLY A VOL TAGE OF 500V DC FOR 1 MIN.TO
FOLLOWING PORTIONS AFTER WHICH MEASUREMENT
SHALL BE MADE:
(1)BETWEEN BODY AND CONDUCTOR.
(2)BETWEEN CONDUCTORS NOT TO BE CONTACT.
输入500V
DC电压1分钟,按以下接触方法测试:
(1)接触端子之间.
(2)塑胶½与端子之间.
AC1500V ims(50-60Hz)FOR 1 MIN
：
(1)BETWEEN TERMINALS.
(2)BETWEEN INDIVDUAL TERMINALS AND FRAME.
输入AC1500V
(50-60Hz)电压1分钟,按以下接触方法测试:
(1)接触端子之间.(2)塑胶½与端子之间.
A-16℃~+85℃
在-16℃~+85℃温度内½用
UNLESS OTHERWISE SPECIFIED. THE STANDARD RANGE
OF ATMOSPHERIC CONDITIONS FOR MAKING
MEASUREMENTS AS FOLLOWS:
(1)AMBIENT TEMPERATURE:5℃TO35℃.
(2)RELATIVE HUMIDITY:45%TO85%.
在没有指定的情况下测试温度,湿度如下:
(1)温度为5℃-35℃.( 2)湿度为45%-85%.
TEMPERATUER：0℃½30℃
温度：0℃½30℃
DEGREE OF HUMIDITY
湿度40％½70％
PERFORMANCE 表现
50mΩMAX
50毫欧以下
4.2
INSULATION
RESISTANCE
绝缘电阻
100MΩ MIN
100兆欧以上
4.3
DIELECTRIC
STRENGTH
耐电压
PRACTICAL
TEMPERATURE
RANGE
½用温度范围
NO DAMAGE TO PARTS
ARCING,OR BREAKDOWN ETC.
没有绝缘破坏等异常.
5
6
STANDARD
ATMOSPHEIC
CONDITIONS
测试标准状态
6.1
STORE
THE
PERIOD
储存期
THREE MONTH
三个月
YuenFung Electrnoic(shenzhen)Co.ltd
源丰电子(深圳）有限公司
承认书编号
YF-ENG-F-30113
A/0
第2页 共3页
2018-9-11
SPECIFICATION
规格书
WRITTEN
制定
版
页
本
次
发布日期
审
核
邓颖恒
APP'D审批
7.MECHANICAL CHARACTERISTICS
机械性½规格:
ITEM项目
7.1
OPERATION
FORCE
½动力
TEST CONDITIONS
测试条件
PERFORMANCE
表现
250±80gf
7.2
TERMINAL
STRENGTH
端子强度
A STATIC LOAD OF1Kgf SHALL BE APPLIED TO THE
TIP OF THE TERMINAL FOF 15 SEC IN ANY DIRECTION
在任意一个方向的先端加上1Kgf力度测试,时间为15秒.
ELECTRICAL
CHARACTERISTICS SHALL BESATISFIED
WITHOUT DAMAGEOR EXCESSIVE
LOOSENESS OF TERMINALS
在排脚中没有裂开,松动等异常,满足于
机械,电器性½.
7.3
LIFE TEST
寿½测试
1.ENDURANCE WITHOUT LOADING:THE TEST SHOULD BE
TAKEN
AT A SPEED OF 6-8 CYCLES FOR 1 MIN;1.5 TIMES OF THE
STANDARD FORCE
无负荷:每分钟6-8回速度测试压力不得超过标准力度1.5倍.进行测试
2.ENDURANCE WITH LOADING:
THE TEST SHOULD BE TAKEN ATA SPEED OF 6-8 CYCLES FOR 1
MIN;
OPERATE PRESSURE SHOULD BE UNDER THE1.5 TIMES OF THE
STANDARD FORCE
负荷:在负荷的条件下以每分钟6-8回的速度压力不得超过标准力度1.5
倍.进行测试
(1).20,000CYCLESCONTACT AT
WITHOUT LOADING.
在无负荷下20,000次接触
(2).10,000 CYCLESMECHANECAL AND
ELECTRICAL CHARACTERISTICS SHALL
BE SATISFIED10,000次满足于机械，电器
性½；
8.DURABILITY
耐久性:
ITEM项目
TEST CONDITIONS
测试条件
PERFORMANCE
表现
THE AREA OF SOLDERING,
SHOULD BE OVER75%.
焊接面积要有75%以上.
THE TOP OF THE TERMINALS SHALL BE DIPPED
SOLDERABILITY 2mmINTHE SOLDER BATH OF 230+10℃ FOR 3+0.5
SECONDS.
TEST
8.1
端子顶部被浸入锡焊池中2mm深,浓度为230+10℃,时间为3+0.5
可焊性试验
秒.
SOLDER BATH METHOD:SOLDER
TEMPERATURE260+5℃,IMMERSION
TIME3+0.5SEC,IMMERSION DEPTH UP TO THE SURFACE
RESISTANCE TO
OF THE BOARD,DIMENSIONS OF COMPONENT HOLES IN
SOLDERING
THE PRINTED WIRING BOARD SHALL BEING
8.2
HEAT TEST
ACCORDANCE WITH THOSE SPECIFIED IN THIS
耐焊性试验
SPECIFICATION.
焊炉焊接的时候温度控制在260+5℃,过炉时间3+0.5秒.
手焊接的时候温度控制在360℃±5℃，时间为3±0.5秒.
WITHOUT DEFORMATION OF CASE
OR EXCESSIVE
LOOSENESS OF TEMINALS
ELECTRICAL CHARACTERISTICS
SHALL BE SATISFIED.
本½无变½,½满足于机械,电器性½.
YuenFung Electrnoic(shenzhen)Co.ltd
源丰电子(深圳）有限公司
承认书编号
YF-ENG-F-30113
A/0
第3页 共3页
2018-9-11
SPECIFICATION
规格书
版
页
本
次
发布日期
审
WRITTEN
制定
核
邓颖恒
APP'D审批
ITEM项目
TEST CONDITIONS
测试条件
PERFORMANCE
表现
8.3
HEAT TEST
耐热试验
THE SWTICH SHALL BE STORED AT A TEMPERATURE OF
85+2℃ FOR 96 HOURS.THEN THE SWITCH SHALLBE
MAINTAINED AT STANDARD ATMOSPHERICCONDITION
FOR 1 HOUR AFTER WHICHMEASUREMENT SHALL BE
MADE.
放½在温度85+2℃中测试96小时后,再放½正常室温中1小时来
测定.
8.4
COLD TEST
耐冷试验
THERE SHALL BE NO
THE SWITCH SHALL BE STORED AT A TEMPERATURE OF DEFORMATION OR
-20+3℃ FOR 96 HOURS,THEN THE SWITCH SHALL BE
CRACKSINMOLDED PART
MAINTAINED AT STANDARD ATMOSPHERIC CONDITION
外观无异常,满足于机械,电器性½.
FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE
MADE.
放½在温度-20+3℃中96小时后,再放½常温中1小时来进行测
试.
THE SWITCH SHALL BE STORED AT A TEMPERATURE OF
40+2℃ AND A HUMIDITY OF 90%TO95% FOR 96
HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT
HUMIDITY TEST
STANDARD ATMOSPHERE CONDITION FOR 1 HOUR
8.5
½湿试验
AFTER WHICH MEASUREMENT SHALL BE MADE.
放½40+2℃试验的相对湿度为90%-95%环境中96小时后,再将
样板放在正常环境1小时后进行测试.
电源技术
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
