深圳市首韩科技有限公司
SHENZHEN SHOUHAN TECHNOLOGYCO.,LTD
Tel: 0755-27597601 Fax: 0755-27597491
承
SPECIFICATION
认
书
FOR APPROVAL
客
户 Customer：
产品名称 Project：
规格型号 Part No：
½触开关
TS35CA
贵公司承认印 Approal slgnatures
料 号/Part No.
签
章/Signatures
日期 Date:
拟制/Drawn
审核/Check
批准/Approved
李春风
刘学
½孝金
1
深圳市首韩科技有限公司
SHENZHEN SHOUHAN TECHNOLOGYCO.,LTD
Page
MODEL
1/8
Tel: 0755-27597601 Fax: 0755-27597491
1、 概述
GENERAL
1.1 适用范围
APPLICATION
此规格书适用于机械式½触开关的相关要求
TS35CA
This specification is applied to the requirements for TACTILE SWITCH (MECHANICAL CONTACT)
1.2 工½温度范围
Operating Temperature Range
－20℃½70℃(在标准大气压、标准湿度条件下)
-20℃½70℃（Normal humidity, normal air pressure）
1.3 贮藏温度范围
Storage Temperature Range
-30℃½80℃(在标准大气压、标准湿度条件下)
-30℃½80℃（Normal humidity, normal air pressure）
1.4
测试条件
Test Conditions
在没有其它特定的条件下，应该在以下的条件下进行测试和测量：
Unless otherwise specified, tests and measurement shall be made in
the following standard conditions:
常温…………………………………5℃½35℃
Normal temperature………………5℃½35℃
标准湿度……………………………相对湿度 25%½85%
Normal humidity…………………relative humidity 25%½85%
标准大气压…………………………86KPa½106Kpa
Normal air pressure…………………86Kpa½106Kpa
在制造过程中，测试和测量应该在以下的条件下进行：
If any doubt arise from the judgment, tests shall be conducted
at the following conditions:
温度…………………………………20℃±2℃
Temperature………………………20℃±2℃
相对湿度……………………………65%±5%
Relative humidity………………65%±5%
环境气压…………………………86KPa½106Kpa
Air pressure…………………………86KPa½106Kpa
深圳市首韩科技有限公司
SHENZHEN SHOUHAN TECHNOLOGYCO.,LTD
Page
2/8
MODEL
Tel: 0755-27597601 Fax: 0755-27597491
2、 详细说明
Detailed specification
2.1 外观：应无½响、降½产品性½的缺陷；
TS35CA
Appearance: There should be no defects that affect the serviceability of product.
2.2
结构尺寸和安装尺寸：应符合装配图要求
Style and dimension: shall conform to the assemble drawings.
2.3
操½½式：有触觉反应的操½
Type of actuating: Tactile feedback.
2.4
开关结构：单回路单输出(具½的触点结构在装配图中已绘出)；
Contact arrangement: 1 pole, 1 throw
(Details of contact arrangement are given in the assembly drawings.)
2.5
开关工½额定值：DC 12V，50mA（有效值）
Ratings: 12V DC, 50mA (effective value)
3、
电气性½：
ELECTRICAL SPECIFICATION
NO.
项目
ITEM
试验条件
TEST CONDITIONS
要求
REQUIREMENTS
3.1
接触电阻
Contact Resistance
在以 5V 10mA 的直流电源或不½于 1KHz 的交
流 电源的电路中，以一个等于 2 倍按力的静负荷
½ 加于手柄中心
Applying a static load of 2 times
≤100mΩ
operating force to the center of the stem,
measurements shall be made by 5V DC 10mA
or more than 1KHZ AC small-current contact
resistance meter.
3.2
绝缘电阻
Insulation
Resistance
在端子之间½加 DC 100V /1min 的条件下,测量
端 子之间底座、盖板的电阻值
Measurement shall be made following
≥100MΩ
application of 100V DC potential, across
terminals, and across terminals and cover,
for one minute.
3.3
介质耐压
Dielectric
voltage proof
在端子之间½加 250V AC(50HZ 或
60HZ)/1min 250V AC (50HZ or 60HZ)
shall be applied across terminals, for
one minute.
无击穿、无飞弧
There should be no breakdown
and flashover
深圳市首韩科技有限公司
SHENZHEN SHOUHAN TECHNOLOGYCO.,LTD
Page
MODEL
3/8
Tel: 0755-27597601 Fax: 0755-27597491
NO.
项目
ITEM
试验条件
TEST CONDITIONS
按照正常½用时的力度½按手柄中心（每秒 3½4
次），
在导通和断开过程中测试开关抖动
Lightly striking the center of the stem at
a rate encountered in normal use (3 to 4
times per second), and bounce shall be
tested at “ON” and “OFF”
开关
Switch
10K¦ Έ
TS35CA
要求
REQUIREMENTS
3.4
触点抖动 Bounce
10V DC
示波器
Oscillograph
ON-3msec.max
OFF-8msec.max
"导通"
"ON"
"断开"
"OFF"
4、
机械性½：
MECHANICAL SPECIFICATION
开关垂直于操½方向放½，在开关驱动件顶端中
心逐渐½力，测量开关导通所需的最大力度
refer to chart 3 按力：
Placing the switch such that the direction
160±50gf
of switch operation is vertical and then
gradually increasing the load applied to
Operating Force:160±50gf
the center of the stem, the maximum load
required for the switch to come to a stop
shall be measured
4.1
按力
Operating Force
4.2
最大行程
Full Travel
开关垂直于操½方向放½，以一个等于 2 倍按
力 的静负荷½加在开关驱动件顶端中心，测量顶
端 移动的距离。
Placing the switch such that the direction
0.2±0.1mm
of switch operation is vertical and then
applying static load of 2times operating
force to the center of the stem; the
travel distance for the switch to come to
a stop shall be measured.
深圳市首韩科技有限公司
SHENZHEN SHOUHAN TECHNOLOGYCO.,LTD
Page
4/8
MODEL
Tel: 0755-27597601 Fax: 0755-27597491
NO.
项目
ITEM
试验条件
TEST CONDITIONS
TS35CA
要求
REQUIREMENTS
4.3
回弹力
Return Force
开关垂直于操½方向放½，在开关驱动件顶端中
心下降至全行程后，测量顶端向自由½½½换的
力度。
refer to chart 3
The sample switch is installed such that
回弹力
the direction of switch operation is
Return Force:50gf min
vertical and upon depressing the stem in
its center to the whole travel distance,
the force of the stem to return to its
free position shall be measured.
4.4
停止强度
Stop Strength
开关垂直于操½方向放½，从操½方向向驱动件
½加 20N 的静负荷持续 1min。
Placing the switch such that the direction
of switch operation is vertical, and then
a static load of 20N shall be applied in
the direction of stem operation for a
period of 1 min.
无机械和电气损坏
There shall be no sign of
damage mechanically and
electrically.
4.5
手柄拔出强度
Stem
Strength
开关垂直于操½方向放½，反方向实½最大操½
力，并测量手柄的行程范围。
Placing the switch such that the direction
of switch operation is vertical, and then 20N.min.
the maximum force to withstand a pull
applied opposite to the direction of stem
operation shall be measured.
4.6
在以下设定条件下进行测量:
Measurements shall be made following the
test set forth below:
(1) 焊接温度:245±5℃
Solder temperature : 245±5℃
可焊性 Solderability (2) 浸入时间:2s±0.5s
Immersion time: 2s±0.5s
对于其它步骤参考《GB 5095.6—86》试验
12a The other steps please refer to《GB
5095.6-86》TEST 12a
除边缘外涂层应均匀覆盖 90%以上
Except for the edge, the
coating should cover a
minimum 90%
PCB设计
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
