HT14F/14FH/FD
Page:
1
宁波博粤电子有限公司
产品承认书
品牌：
型号：
客户：
日期：
Htv
继电器
HT14F/FH/FD
供应商签章
客户确认签章
------------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
HT14F/14FH/FD
Page:
2
1.
安全认证:
Safety Standard:
C-UL TUV
2.
接点规格:
Contact Specification:
2.1
接点间隙:
Contact Gap:
2.2
接点阻抗:
Contact Resistance
最小
0.3 mm。
0.3mm Minimum.
初始值最大
100mΩ；
流通电流
1A、开路测试电压: 6VDC；
½用电压下降法量测。
Maximum 100mΩ at initial value.
Test Current: 1A, Open Circuit Test Voltage: 6VDC.
By using Voltage Drop Method.
HT14F： 250VAC Cosφ =1，可通过电流为 10
安培。
30VDC
，可通过电流为
10
安培。
10Amps at 250VAC Cosφ =1.
10Amps at 30VDC
HT14FH：250VAC Cosφ =1，可通过电流为 16
安培。
30VDC
，可通过电流为
16
安培。
16Amps at 250VAC Cosφ =1.
16Amps at 30VDC
HT14FD：250VAC Cosφ =1，可通过电流为 5
安培。
30VDC
，可通过电流为
5
安培。
5Amps at 250VAC Cosφ =1.
5Amps at 30VDC
2.3
接点容量:
Contact Capacity:
3.
摄氏
20
度之线圈规格:
Coil Specification at 20 °
C:
3.1
额定电压:
Rated Voltage:
3.2
额定电流:(
mA± 10%)
Nominal Current:
3VDC
176/240
5VDC
106/139
6VDC
88/120
9VDC
56/78
12VDC
44/60
24VDC
22/30
48VDC
11/15
------------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
HT14F/14FH/FD
Page:
3
3.3
额定消耗功率:
(± 10%.)
Rated Power Consumption:
3.4
线圈阻抗:
(Ω± 10%.)
17/12.5
Coil Resistance:
3.5
感动电压:
Pull In Voltage:
0.53W/0.72W
47/36
68/50
160/115
275/200 1100/820 4170/3300
≦
(½电压渐渐½加于继电器时接点之动½电压，为额定电压之 75%)
V DC
≦
(Contact operating voltage when voltage is gradually applied. It is
75% of the Rated Voltage) V DC
≧
(½额定电压渐渐的减少时接点放开之电压，为额定电压之 10%) VDC
≧
(Contact breaking voltage when rated voltage is gradually reduced.
It is 10% of the Rated Voltage) VDC
(为额定电压之 140%) V DC
(140% of the Rated Voltage) V DC
在½加额定电压时最大为
15milliseconds。
15milliseconds Maximum when rated Voltage is applied.
在额定电压突然消失时最大为
5 milliseconds.。
5milliseconds Maximum when rated Voltage is suddenly cut off.
在空½½时线圈½加最大可允许电压，待温度稳定后量测的温度不可超过
40℃。(不包含环境温度)
40℃ Maximum.
Maximum Allowable Voltage is applied to Coil while no load should be
applied to Contacts, then the temperature should be measured when the
value is stabilized. Environment temperature should not be included in.
3.6
开放电压:
Drop Out Voltage:
3.7
最大应加电压:
Max. Allowable Voltage:
3.8
动½时间:
Operate Time:
3.9
开放时间
Release Time:
3.10
线圈温升:
Coil Temperature Rise:
4.
电气特性:
Electrical Characteristics:
4.1
½用寿½:
Life Expectancy:
------------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
HT14F/14FH/FD
Page:
4
4.1.1
电气寿½:
Electrical Life:
HT14F
10A/250VAC Cosφ =1，
½加额定电压时，
100,000
次以上之电气寿½。
有
10A/30VDC
，½加额定电压时，有
100,000
次以上之电气寿½。
100,000 operations Minimum at10A/250VAC Cosφ =1.
100,000 operations Minimum at 10A/30VDC
Rated Voltage is applied.
HT14FH
16A/250VAC Cosφ =1，
½加额定电压时，
100,000
次以上之电气寿½。
有
16A/30VDC
，½加额定电压时，有
100,000
次以上之电气寿½。
100,000 operations Minimum at16A/250VAC Cosφ =1.
100,000 operations Minimum at 16A/30VDC
Rated Voltage is applied.
HT14FD
5A/250VAC Cosφ =1，½加额定电压时，有 100,000
次以上之电气寿½。
5A/30VDC
，½加额定电压时，有
100,000
次以上之电气寿½。
100,000 operations Minimum at 5A/250VAC Cosφ =1.
100,000 operations Minimum at 5A/30VDC
Rated Voltage is applied.
在无负½½的情况下有
10,000,000
次以上之机械寿½。
10,000,000 operations Minimum at No Load condition.
电气: 每分钟
30
次。
机械: 每分钟
300
次。
Electrical: 30 operations/minute.
Mechanical: 300 operations/minute.
4.1.2
机械寿½:
Mechanical Life:
4.1.3
最大操½频率
Maximum Operating
Frequency:
4.2
介质耐压:
Dielectric Strength:
4.2.1
接点对接点间:
Between Contacts:
1000VAC，50/60 Hz，漏电流小于 1mA，持续一分钟。
1000VAC at Test Frequency 50/60 Hz, Leakage Current: 1mA for 1
minute.
5000VAC，50/60 Hz，漏电流小于 1mA，持续一分钟。
5000VAC at Test Frequency 50/60 Hz, Leakage Current: 1mA for 1
minute.
在½加
500VDC
绝缘阻抗之量测值需≧100
MΩ。
≧100
MΩ Minimum.
A Voltage of 500VDC should be applied after which measurement shall
be made.
4.2.2
线圈对接点间:
Between Coil &
Contact:
4.3
绝缘阻抗:
Insulation Resistance:
4.4
振动测试:
Vibration
------------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
HT14F/14FH/FD
4.4.1
振动
I（强度）:
Endurance I:
Page:
5
在无激磁状态下双振幅½度为
1.5mm，震动频率在一分钟内由
10HZ~55HZ~10HZ。XYZ
各方向各进行
2
小时，共六小时，实验后外观
构造不可异常，且电气功½需符合规格之要求。
The Coil shall be maintained under not energized condition, double
amplitude 1.5 mm, the entire frequency range changes from 10 to 55 Hz
then returns to 10 Hz shall be made in 1 minute. This motion shall be
applied for a period of 2 hours in each of 3 mutually perpendicular axis (a
total of 6 hours) There should not be any deformations in construction
and in appearance, while the Electrical Specifications should be fulfilled
after the test.
在激磁状态下双振幅½度是
1.5mm，震动频率在一分钟内由
10HZ~55HZ~10HZ。XYZ
各方向进行
5
分钟，实验中不得有误(接点断开
时间不可超过
1 mS)。实验后外观，构造不可异常，且电气功½需符合规
格之要求。
The Coil shall be maintained under energized condition, double
amplitude 1.5 mm, the entire frequency range changes from 10 to 55 Hz
then returns to 10 Hz shall be made in 1 minute. This motion shall be
applied for a period of 5 minutes in 3 mutually perpendicular axis.
Malfunction is not allowed during the test (contact breaking time should
be less than 1 millisecond) In addition, there should not be any
deformations in construction and in appearance while the Electrical
Specifications should be fulfilled after the test.
4.4.2
振动
II (稳定性):
Endurance II (Error
Operation):
4.5
冲击测试:
Shock:
4.5.1
耐冲击性
I（强度）:
Endurance I:
在无激磁状态加速度
1000m/s
2
冲击情况下，XYZ 各方向进行
5
次，实验
后外观，构造不可异常，且电气功½需符合规格之要求。
Peak Acceleration: 1000m/s
2
The Coil shall be maintained under not energized condition, 5
successive shocks shall be applied in 3 mutually perpendicular axis.
There should not be any deformations in construction and in appearance
while the Electrical Specifications should be fulfilled after the test.
在激磁状态加速度
100m/s
2
冲击情况下，XYZ 各方向进行
2
次，实验中不
得有误(接点断开时间不可超过
1 mS)，实验后外观，构造不可异常，且电
气功½需符合规格之要求。
Peak Acceleration: 100m/s
2
The Coil should be maintained under energized condition, 2 successive
shocks shall be applied in 3 mutually perpendicular axis. Malfunction is
not allowed during the test (contact breaking time should be less than 1
millisecond) In addition, there should not be any deformations in
construction and in appearance while the Electrical Specifications should
be fulfilled after the test.
4.5.2
耐冲击性
II (稳定性):
Endurance II (Error
Operation):
5.
环境特性:
Environmental
Characteristics:
5.1
温度范围:
Temperature Range:
------------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
Linux开发
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
