HT90-SC(SCP)-30A
Page:
1
宁波博粤电子有限公司
产品承认书
品牌：
型号：
客户：
日期：
Htv
继电器
HT90-SCP (30A)
供应商签章
客户确认签章
---------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
HT90-SC(SCP)-30A
Page:
2
.
1.
安全认证:
Safety Standard:
C-UL TUV
、CQC
2.
接点规格:
Contact Specification:
2.1
接点间隙:
Contact Gap:
2.2
接点阻抗:
Contact Resistance
1A、1B、1C
最小
0.3 mm。
0.3mm Minimum.
初始值最大
100mΩ；
流通电流
1A、开路测试电压: 6VDC；
½用电压下降法量测。
Maximum 100mΩ at initial value.
Test Current: 1A, Open Circuit Test Voltage: 6VDC.
By using Voltage Drop Method.
HT90-A/AP
125VAC Cosφ =1，可通过电流为 40
安培。
30VDC
，可通过电流为
40
安培。
277VAC Cosφ =1，可通过电流为 30
安培。
30VDC
，可通过电流为
30
安培
40 Amps at125VAC Cosφ =1.
40 Amps at 30VDC
30 Amps at277VAC Cosφ =1.
30 Amps at 30VDC
HT90-B/BP
125VAC Cosφ =1，可通过电流为 30
安培。
30VDC
，可通过电流为
30
安培。
277VAC Cosφ =1，可通过电流为 20
安培。
30VDC
，可通过电流为
30
安培
20 Amps at 277VAC Cosφ =1.
20Amps at 30VDC
HT90-C/CP
250VAC Cosφ =1，30VDC
可通过电流
NO:30A 250VAC/30VDC NC: 20A 250VAC/30VDC
at 240VAC Cosφ =1 at 30VDC
NO:30A 250VAC/30VDC NC: 20A 250VAC/30VDC
2.3
接点容量:
Contact Capacity:
---------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
HT90-SC(SCP)-30A
Page:
3
3.
摄氏
20
度之线圈规格:
Coil Specification at 20 °
C:
3.1
额定电压:
Rated Voltage:
3.2
额定电流:(±
10%)
Nominal Current:
3.3
额定消耗功率:
(± 10%.)
Rated Power Consumption:
3.4
线圈阻抗:
(± 10%.)
Coil Resistance:
3.5
感动电压:
Pull In Voltage:
5VDC
185mA
6VDC
150mA
9VDC
93mA
12VDC
77mA
0.9W
27
40
97
155
660
2560
13450
24VDC
36mA
48VDC
18mA
110VDC
8.2mA
≦
(½电压渐渐½加于继电器时接点之动½电压，为额定电压之 75%)
V DC
≦
(Contact operating voltage when voltage is gradually applied. It is
75% of the Rated Voltage) V DC
≧
(½额定电压渐渐的减少时接点放开之电压，为额定电压之 10%) VDC
≧
(Contact breaking voltage when rated voltage is gradually reduced. It
is 10% of the Rated Voltage) VDC
(为额定电压之 130%) V DC
(130% of the Rated Voltage) V DC
在½加额定电压时最大为
15milliseconds。
15milliseconds Maximum when rated Voltage is applied.
在额定电压突然消失时最大为
10 milliseconds.。
10milliseconds Maximum when rated Voltage is suddenly cut off.
在空½½时线圈½加最大可允许电压，待温度稳定后量测的温度不可超过
50℃。(不包含环境温度)
50℃ Maximum.
Maximum Allowable Voltage is applied to Coil while no load should be
applied to Contacts, then the temperature should be measured when the
value is stabilized. Environment temperature should not be included in.
3.6
开放电压:
Drop Out Voltage:
3.7
最大过½½电压:
Max. Allowable Voltage:
3.8
动½时间:
Operate Time:
3.9
开放时间
Release Time:
3.10
线圈温升:
Coil Temperature Rise:
4.
电气特性:
Electrical Characteristics:
4.1
½用寿½:
Life Expectancy:
---------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
HT90-SC(SCP)-30A
Page:
4
4.1.1
电气寿½:
Electrical Life:
HT90-A/AP
40A/125VAC Cosφ =1，½加额定电压时，有 100,000
次以上之电气寿½。
40A/30VDC
，½加额定电压时，有
100,000
次以上之电气寿½。
30A/277VAC Cosφ =1，½加额定电压时，有 100,000
次以上之电气寿½。
30A/30VDC
，½加额定电压时，有
100,000
次以上之电气寿½
100,000 operations Minimum at 40A/125VAC Cosφ =1.
100,000 operations Minimum at 40A/30VDC
100,000 operations Minimum at 30A/277VAC Cosφ =1.
100,000 operations Minimum at 30A/30VDC
Rated Voltage is applied.
HT90-B/BP
30A/125VAC Cosφ =1，½加额定电压时，有 100,000
次以上之电气寿½。
30A/30VDC
，½加额定电压时，有
100,000
次以上之电气寿½。
20A/277VAC Cosφ =1，½加额定电压时，有 100,000
次以上之电气寿½。
20A/30VDC
，½加额定电压时，有
100,000
次以上之电气寿½
100,000 operations Minimum at 30A/125VAC Cosφ =1.
100,000 operations Minimum at 30A/30VDC
100,000 operations Minimum at 20A/277VAC Cosφ =1.
100,000 operations Minimum at 20A/30VDC
Rated Voltage is applied.
HT90-C/CP
NO:30A 250VAC (Cosφ =1)/30VDC NC: 20A 250VAC(Cosφ =1)/30VDC
有
100,000
次以上之电气寿½。
100,000 operations Minimum at NO:30A 250VAC (Cosφ =1)/30VDC
NC: 20A 250VAC(Cosφ =1)/30VDC
Rated Voltage is applied.
4.1.2
机械寿½:
Mechanical Life:
4.1.3
最大操½频率
Maximum Operating
Frequency:
4.2
介质耐压:
Dielectric Strength:
4.2.1
接点对接点间:
Between Contacts:
4.2.2
线圈对接点间:
Between Coil &
Contact:
4.3
绝缘阻抗:
Insulation Resistance:
1500VAC，50/60 Hz，漏电流小于 1mA，持续一分钟。
1500VAC at Test Frequency 50/60 Hz, Leakage Current: 1mA for 1
minute.
1500VAC，50/60 Hz，漏电流小于 1mA，持续一分钟。
1500VAC at Test Frequency 50/60 Hz, Leakage Current: 1mA for 1
minute.
在½加
500VDC
绝缘阻抗之量测值需≧100
MΩ。
≧100
MΩ Minimum.
A Voltage of 500VDC should be applied after which measurement shall be
made.
在无负½½的情况下有
10,000,000
次以上之机械寿½。
10,000,000 operations Minimum at No Load condition.
电气: 每分钟
30
次。
机械: 每分钟
300
次。
Electrical: 30 operations/minute.
Mechanical: 300 operations/minute.
4.4
振动测试:
Vibration
---------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
HT90-SC(SCP)-30A
4.4.1
振动
I（强度）:
Endurance I:
Page:
5
在无激磁状态下双振幅½度为
1.5mm，震动频率在一分钟内由
10HZ~55HZ~10HZ。XYZ
各方向各进行
2
小时，共六小时，实验后外观构
造不可异常，且电气功½需符合规格之要求。
The Coil shall be maintained under not energized condition, double
amplitude 1.5 mm, the entire frequency range changes from 10 to 55 Hz
then returns to 10 Hz shall be made in 1 minute. This motion shall be
applied for a period of 2 hours in each of 3 mutually perpendicular axis (a
total of 6 hours) There should not be any deformations in construction and
in appearance, while the Electrical Specifications should be fulfilled after
the test.
在激磁状态下双振幅½度是
1.5mm，震动频率在一分钟内由
10HZ~55HZ~10HZ。XYZ
各方向进行
5
分钟，实验中不得有误(接点断开
时间不可超过
1 mS)。实验后外观，构造不可异常，且电气功½需符合规格
之要求。
The Coil shall be maintained under energized condition, double amplitude
1.5 mm, the entire frequency range changes from 10 to 55 Hz then
returns to 10 Hz shall be made in 1 minute. This motion shall be applied
for a period of 5 minutes in 3 mutually perpendicular axis. Malfunction is
not allowed during the test (contact breaking time should be less than 1
millisecond) In addition, there should not be any deformations in
construction and in appearance while the Electrical Specifications should
be fulfilled after the test.
4.4.2
振动
II (稳定性):
Endurance II (Error
Operation):
4.5
冲击测试:
Shock:
4.5.1
耐冲击性
I（强度）:
Endurance I:
4.5.2
耐冲击性
II (稳定性):
Endurance II (Error
Operation):
在无激磁状态加速度
1000m/s
2
冲击情况下，XYZ 各方向进行
5
次，实验后
外观，构造不可异常，且电气功½需符合规格之要求。
Peak Acceleration: 1000m/s
2
The Coil shall be maintained under not energized condition, 5 successive
shocks shall be applied in 3 mutually perpendicular axis. There should
not be any deformations in construction and in appearance while the
Electrical Specifications should be fulfilled after the test.
在激磁状态加速度
100m/s
2
冲击情况下，XYZ 各方向进行
2
次，实验中不
得有误(接点断开时间不可超过
1 mS)，实验后外观，构造不可异常，且电
气功½需符合规格之要求。
Peak Acceleration: 100m/s
2
The Coil should be maintained under energized condition, 2 successive
shocks shall be applied in 3 mutually perpendicular axis. Malfunction is
not allowed during the test (contact breaking time should be less than 1
millisecond) In addition, there should not be any deformations in
construction and in appearance while the Electrical Specifications should
be fulfilled after the test.
5.
环境特性:
Environmental
Characteristics:
5.1
温度范围:
Temperature Range:
---------------------------------------------------------------------------------------------------------------------------
宁波博粤电子有限公司
宁波市鄞州区四明中路688号 TEL:0574-88120933 FAX:0574-88120533
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
